LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2023 >> Escape Platinum >> Repair and Diagnosis >> External Pages >> Different car >> Section 1338 (Fuel System - General Information - 1.5L ECOBOOST (132KW/180PS) - I3 (Y1)) >> General Procedures >> Quick Release Coupling

Quick Release Coupling

WARNING: This page is about a different car, the 2022 Ford Bronco Sport. However, it is still accessible from the selected car via links, so may be relevant.

For information on Ford Color Coded Illustrations refer to OEM COLOR CODING

Disconnect 

NOTE: When reusing liquid or vapor tube connections, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 1 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release .
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
  3. GFD691929Courtesy of FORD MOTOR COMPANY
  4. GFD691930Courtesy of FORD MOTOR COMPANY

Connect 

  1. Push the quick release coupling onto the tube.
    GFD691931Courtesy of FORD MOTOR COMPANY
  2. NOTE: Make sure the retainer clip is fully seated and locked onto the tube by pulling on the quick connect coupling.

    Press the retainer clip into the quick release coupling body until flush and the tabs are locked in place.

    GFD691932Courtesy of FORD MOTOR COMPANY
  3. Connect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid or vapor tube connections, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 2 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release .
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
  3. GFD691933Courtesy of FORD MOTOR COMPANY
  4. GFD691934Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD691935Courtesy of FORD MOTOR COMPANY
  2. GFD691936Courtesy of FORD MOTOR COMPANY
  3. Connect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid or vapor tube connections, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 3 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release .
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
  3. GFD691937Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD691938Courtesy of FORD MOTOR COMPANY
  2. GFD691939Courtesy of FORD MOTOR COMPANY
  3. Connect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid or vapor tube connections, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 4 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release .
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
  3. GFD691940Courtesy of FORD MOTOR COMPANY
  4. GFD691941Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD691942Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 5 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release .
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
  3. GFD691943Courtesy of FORD MOTOR COMPANY
  4. GFD691944Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD691945Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 6 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release .
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
  3. Press the tabs of the rear retainer clip and pull it to the outward position.
    GFD691946Courtesy of FORD MOTOR COMPANY
  4. GFD691947Courtesy of FORD MOTOR COMPANY

Connect 

  1. Pull on the quick release coupling to make sure it is securely fastened.
    GFD691948Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 7 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release .
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
  3. GFD691949Courtesy of FORD MOTOR COMPANY
  4. GFD691950Courtesy of FORD MOTOR COMPANY

Connect 

  1. Pull on the quick connect coupling to make sure it is securely fastened.
    GFD691951Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 8 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release .
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
  3. GFD691943Courtesy of FORD MOTOR COMPANY
  4. GFD691944Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD691945Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 9 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release .
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
    1. Release the secondary locking tab.
    2. Depress the primary locking tab.
    3. Separate the quick release coupling from the tube.
    GFD691952Courtesy of FORD MOTOR COMPANY

Connect 

    1. Push the quick release coupling onto the tube.
    2. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Lock the secondary locking tab.

    GFD691953Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 10 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release .
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
    1. Push on the locking tab.
    2. Lift the clip.
    GFD691954Courtesy of FORD MOTOR COMPANY
    1. Depress the tabs inward.
    2. Push the clip downward.
    3. Separate the quick release coupling from the fuel line.
    GFD691955Courtesy of FORD MOTOR COMPANY

Connect 

    1. Push the quick release coupling onto the tube.
    2. Push the clip down into the quick release coupling.
    3. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

    GFD691956Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 11 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release .
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
  3. GFD691957Courtesy of FORD MOTOR COMPANY

Connect 

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

    GFD691957Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 12 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release .
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
  3. GFD691958Courtesy of FORD MOTOR COMPANY
  4. GFD691959Courtesy of FORD MOTOR COMPANY

Connect 

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

    GFD691960Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 13 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release .
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
  3. GFD691961Courtesy of FORD MOTOR COMPANY

Connect 

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

    GFD691962Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 14 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release .
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
  3. GFD691963Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD691964Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid or vapor tube connections, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 15 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Press both retaining tabs inward and remove quick release coupling from fuel tube.
    GFD691965Courtesy of FORD MOTOR COMPANY

Connect 

  1. NOTE: Inspect and clean both quick release coupling ends.

    Install the quick release coupling onto the tube until it is fully seated.

    GFD691966Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 16 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release .
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
  3. GFD691967Courtesy of FORD MOTOR COMPANY

Connect 

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

    GFD691967Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 17 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release .
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
  3. GFD691968Courtesy of FORD MOTOR COMPANY

Connect 

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

    GFD691969Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 18 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release .
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
  3. GFD691970Courtesy of FORD MOTOR COMPANY

Connect 

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

    GFD691971Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 19 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release .
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
  3. GFD691972Courtesy of FORD MOTOR COMPANY

Connect 

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

    GFD691973Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 20 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release .
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
  3. GFD691974Courtesy of FORD MOTOR COMPANY

Connect 

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

    GFD691975Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 21 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release .
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
  3. GFD691976Courtesy of FORD MOTOR COMPANY

Connect 

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

    GFD691977Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 22 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release .
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
  3. GFD691978Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD691979Courtesy of FORD MOTOR COMPANY
  2. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

    Snap the locking tab into place.

    GFD691980Courtesy of FORD MOTOR COMPANY
  3. NOTE: Make sure that all fuel connections are checked for leaks.
    NOTE: This step is only necessary if a new component is installed.

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

    GFD691981Courtesy of FORD MOTOR COMPANY
  4. Connect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 23 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release .
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
  3. GFD691982Courtesy of FORD MOTOR COMPANY

Connect 

  1. NOTE: Make sure the retainer clip is fully seated and locked onto the tube by pulling on the quick connect coupling.

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

    GFD691983Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 24 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release .
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
  3. GFD691984Courtesy of FORD MOTOR COMPANY

Connect 

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

    GFD691985Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 25 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release .
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
    1. Depress the clip into the quick release coupling.
    2. Separate the quick release coupling from the tube.
    GFD691986Courtesy of FORD MOTOR COMPANY

Connect 

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

    GFD691987Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 26 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release .
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
    1. Remove the quick release coupling from the tube.
    GFD691988Courtesy of FORD MOTOR COMPANY

Connect 

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

    GFD691989Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid or vapor tube connections, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 27 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release .
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
  3. GFD691990Courtesy of FORD MOTOR COMPANY
  4. Remove the quick release coupling from the tube.
    GFD691991Courtesy of FORD MOTOR COMPANY

Connect 

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

    GFD691992Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to: Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
scientia non olet · About LEMON Manuals