DTC Chart: IPMB - 2 Camera System

WARNING: This page is about a different car, the 2018 Ford F-550 Super Duty, 2018 Ford F-450 Super Duty, 2018 Ford F-350 Super Duty, and 2018 Ford F-250 Super Duty. However, it is still accessible from the selected car via links, so may be relevant.

DTC	Description	Action
B115E:08	Camera Module: Bus Signal/Message Failure	GO to Pinpoint Test E
B115E:49	Camera Module: Internal Electronic Failure	Sets in continuous memory and on-demand in the IPMB when an internal fault is detected in the rear parking aid camera. CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the IPMB self-test. If DTC B115E:49 returns, INSTALL a new rear parking aid camera. Refer to: Rear Parking Aid Camera .
B115E:55	Camera Module: Not Configured	NOTE: A LIN circuit fault may prevent the front or rear parking aid camera from being configured properly. VERIFY the integrity of the LIN circuit wiring, terminals and connectors when diagnosing a camera configuration concern. Sets in continuous memory and on-demand in the IPMB when the rear parking aid camera is not configured.VERIFY the battery voltage and condition.PERFORM the rear parking aid camera configuration using a diagnostic scan tool under Electrical>Service Functions>LIN New Module Initialization.
B148E:08	Front Camera: Bus Signal/Message Failure	GO to Pinpoint Test F
B148E:49	Front Camera: Internal Electronic Failure	Sets in continuous memory and on-demand in the IPMB when an internal fault is detected in the CHMSL parking aid camera. CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the IPMB self-test. If DTC B148E:49 returns, INSTALL a new CHMSL parking aid camera. Refer to: High Mounted Stoplamp .
B148E:55	Front Camera: Not Configured	NOTE: A LIN circuit fault may prevent the front or rear parking aid camera from being configured properly. VERIFY the integrity of the LIN circuit wiring, terminals and connectors when diagnosing a camera configuration concern. Sets in continuous memory and on-demand in the IPMB when the CHMSL camera is not configured.VERIFY the battery voltage and condition.PERFORM the front camera configuration using a diagnostic scan tool under Electrical>Service Functions>LIN New Module Initialization.
B14A5:11	Multi-Camera View Switch: Circuit Short To Ground	GO to Pinpoint Test R
U0121:87	Lost Communication With Anti-Lock Brake System (ABS) Control Module: Missing Message	GO to Pinpoint Test S
U0415:00	Invalid Data Received From Anti-Lock Brake System (ABS) Control Module: No Sub Type Information	RETRIEVE and FOLLOW non-network Diagnostic Trouble Codes (DTCs) from the ABS module. See the ABS module DTC Chart. Refer to: Anti-Lock Brake System (ABS) and Stability Control . If no Diagnostic Trouble Codes (DTCs) are present in the ABS module, DIAGNOSE the observable symptom.
U201A:55	Control Module Main Calibration Data: Not Configured	VERIFY the battery voltage and condition. CHECK the vehicle service history for recent service actions related to this module. This continuous memory DTC can set due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, INSTALL As-Built data from Professional Technician Society (PTS), following the diagnostic scan tool instructions under Module Programming>As-Built. Refer to: Module Configuration - System Operation and Component Description . If there have not been recent service actions with this module, INSTALL a new IPMB to correct the failure to retain configuration data. Refer to: Image Processing Module B (IPMB) .
U2100:00	Initial Configuration Not Complete: No Sub Type Information	VERIFY the battery voltage and condition. CHECK the vehicle service history for recent service actions related to this module. This continuous memory DTC can set due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, INSTALL As-Built data from Professional Technician Society (PTS), following the diagnostic scan tool instructions under Module Programming>As-Built. Refer to: Module Configuration - System Operation and Component Description . If there have not been recent service actions with this module, INSTALL a new IPMB to correct the failure to retain configuration data. Refer to: Image Processing Module B (IPMB) .
U3000:42	Control Module: General Memory Failure	RETRIEVE and REPAIR all other IPMB Diagnostic Trouble Codes (DTCS) and TEST the system for normal operation. If DTC U3000:42 is still present after all other Diagnostic Trouble Codes (DTCs) have been repaired, INSTALL a new IPMB. Refer to: Image Processing Module B (IPMB) .