Pinpoint Test F: B1B44:08

WARNING: This page is about a different car, the 2021 Ford F-150. However, it is still accessible from the selected car via links, so may be relevant.

NOTE: Before disconnecting the IPMA or any of the parking aid sensors, verify the connectors are properly seated and latched.

Refer to PARKING AID for schematic and connector information.

Normal Operation and Fault Conditions

REFER to: Parking Aid - System Operation and Component Description .

DTC Fault Trigger Conditions

DTC	Description	Fault Trigger Condition
IPMA B1B44:08	Right Rear Outer Sensor: Bus Signal/Message Failures	A continuous and on-demand DTC that sets in the IPMA when there is a message failure on the LIN for the RHR outer parking aid sensor.

Possible Sources

Wiring, terminals or connectors
RHR outer parking aid sensor
IPMA

F1 CHECK THE DIAGNOSTIC TROUBLE CODES (DTCS) FROM THE IPMA (IMAGE PROCESSING MODULE A) SELF-TEST
- Ignition ON.
- Using a diagnostic scan tool, carry out the IPMA self-test.
- Check the parking aid Diagnostic Trouble Codes (DTCs) from the self-test.
Are Diagnostic Trouble Codes (DTCs) for multiple rear parking aid sensors recorded?

Yes GO to F2

No * For DTC B1B44:08 GO to F3
* For all other IPMA Diagnostic Trouble Codes (DTCs), REFER to the IPMA DTC Chart.

F2 CHECK THE REAR BUMPER WIRING HARNESS
- Inspect the rear bumper wiring harness for opens, shorts, grounds or corrosion.
Is the rear bumper wiring harness OK?

Yes GO to F3

No REPAIR or INSTALL a new rear bumper wiring harness.

F3 CHECK FOR VOLTAGE TO THE SENSOR

Ignition OFF.

Disconnect RHR outer parking aid sensor C4011.

Ignition ON.

Measure:

Positive Lead	Measurement / Action	Negative Lead
C4011-1	Courtesy of FORD MOTOR COMPANY	Ground

Is the voltage greater than 9 volts?

Yes

GO to F4

No	REPAIR the circuit.

F4 CHECK FOR GROUND AT THE SENSOR

Measure:

Positive Lead	Measurement / Action	Negative Lead
C4011-1	Courtesy of FORD MOTOR COMPANY	C4011-3

Is the voltage greater than 9 volts?

Yes

GO to F5

No	REPAIR the circuit.

F5 CHECK THE SENSOR FOR A SHORT TO POWER

Disconnect IPMA C242A.

Ignition ON.

Measure:

Positive Lead	Measurement / Action	Negative Lead
C4011-2	Courtesy of FORD MOTOR COMPANY	Ground

Is any voltage present?

Yes	REPAIR the affected circuits.

GO to F6

F6 CHECK THE SENSOR FOR A SHORT TO GROUND

Ignition OFF.

Measure:

Positive Lead	Measurement / Action	Negative Lead
C4011-2	Courtesy of FORD MOTOR COMPANY	Ground

Is the resistance greater than 10, 000 ohms?

Yes

GO to F7

No	REPAIR the circuit.

F7 CHECK THE SENSOR FOR A SHORT TO VREF OR SIGNAL RETURN CIRCUITS

Ignition OFF.

Measure:

Positive Lead	Measurement / Action	Negative Lead
C4011-2	Courtesy of FORD MOTOR COMPANY	C4011-1
C4011-2	Courtesy of FORD MOTOR COMPANY	C4011-3

Are the resistances greater than 10, 000 ohms?

Yes

GO to F8

No	REPAIR the affected circuits.

F8 CHECK THE SENSOR CIRCUITS FOR AN OPEN

Ignition OFF.

Measure:

Positive Lead	Measurement / Action	Negative Lead
C4011-1	Courtesy of FORD MOTOR COMPANY	C242A-15
C4011-2	Courtesy of FORD MOTOR COMPANY	C242A-6
C4011-3	Courtesy of FORD MOTOR COMPANY	C242A-4

Are the resistances less than 3 ohms?

Yes

GO to F9

No	REPAIR the affected circuit.

F9 INSTALL A KNOWN GOOD SENSOR
- Connect IPMA C242A.
- Install a known good sensor for the suspect RHR outer parking aid sensor. REFER to: Rear Parking Aid Sensor .
- Ignition ON.
- Using a diagnostic scan tool, clear the IPMA Diagnostic Trouble Codes (DTCs) and repeat the self-test.
Is DTC B1B44:08 still present?

Yes GO to F10

No INSTALL a new RHR outer parking aid sensor. REFER to: Rear Parking Aid Sensor .

F10 CHECK FOR CORRECT IPMA (IMAGE PROCESSING MODULE A) OPERATION

Ignition OFF.

Disconnect and inspect all IPMA connectors.

Repair:
- corrosion (install new connector or terminals - clean module pins)
- damaged or bent pins - install new terminals/pins
- pushed-out pins - install new pins as necessary

Reconnect the IPMA connectors. Make sure they seat and latch correctly.

Operate the system and determine if the concern is still present.

Is the concern still present?

Yes	CHECK OASIS for any applicable service articles: TSB, GSB, SSM or FSA. If a service article exists for this concern, DISCONTINUE this test and FOLLOW the service article instructions. If no service articles address this concern, INSTALL a new IPMA. REFER to: Image Processing Module A (IPMA) .

No	The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector. ADDRESS the root cause of any connector or pin issues.