Pinpoint Test Z: DTC (Diagnostic Trouble Code) B15ED:14, DTC (Diagnostic Trouble Code) B15ED:15

WARNING: This page is about a different car, the 2021 Ford F-150. However, it is still accessible from the selected car via links, so may be relevant.

Refer to VEHICLE EMERGENCY MESSAGING SYSTEM for schematic and connector information.

Normal Operation and Fault Conditions

REFER to: Blind Spot Information System - System Operation and Component Description .

DTC Fault Trigger Conditions

DTC	Description	Fault Trigger Condition
IPMA B15ED:14	Side Obstacle Detector "B": Circuit Short To Ground Or Open	An continuous memory DTC that sets in the IPMA if an excessive current draw is detected on the SODR output circuit.
IPMA B15ED:15	Side Obstacle Detector "B": Circuit Short To Battery Or Open	An continuous memory DTC that sets in the IPMA when an open circuit is detected on the SODR output circuit.

Possible Sources

Wiring, terminals or connectors
SODR
IPMA

NOTE: Use the correct probe adapter(s) when making measurements. Failure to use the correct probe adapter(s) may cause damage to the connector. Use only Rotunda Flex Probes (NUD105-R025D)

Z1 CHECK THE IPMA (IMAGE PROCESSING MODULE A) DIAGNOSTIC TROUBLE CODES (DTCS)

Ignition ON.

Using a diagnostic scan tool, perform the IPMA self-test.

Is DTC B15ED:14 or DTC B15ED:15 present?

Yes	For DTC B15ED:14, GO to Z2 For DTC B15ED:15, GO to Z5

No	The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.

Z2 CHECK FOR SHORT TO GROUND WITH THE SODR (SIDE OBSTACLE DETECTION CONTROL MODULE RH) DISCONNECTED
- Ignition OFF.
- For Incandescent rear lamps.
- Disconnect: SODR C415B.
- For LED rear lamps.
- Disconnect: SODR C4484.
- Ignition ON.
- Using a diagnostic scan tool, clear the IPMA Diagnostic Trouble Codes (DTCs).
- NOTE: DTC B15ED:15 may be present during this step and can be disregarded at this time.
  
  Perform the IPMA self-test.
Is DTC B15ED:14 present?

Yes INSTALL a new SODR. REFER to: Side Obstacle Detection Control Module .

No GO to Z3

Z3 CHECK THE IPMA (IMAGE PROCESSING MODULE A) OUTPUT CIRCUIT FOR A SHORT TO GROUND

Ignition OFF.

Disconnect: IPMA C242B.

For Incandescent rear lamps, measure:

Positive Lead	Measurement / Action	Negative Lead
C242B-11	Courtesy of FORD MOTOR COMPANY	Ground

For LED rear lamps, measure:

Positive Lead	Measurement / Action	Negative Lead
C242B-11	Courtesy of FORD MOTOR COMPANY	Ground

Is the resistance greater than 10, 000 ohms?

Yes

GO to Z4

No	REPAIR the circuit. After the repair, CLEAR the DTC, CYCLE the ignition, and RUN the IPMA on-demand self-test to re-enable the circuit.

Z4 CHECK IPMA (IMAGE PROCESSING MODULE A) CIRCUITS FOR A SHORT TOGETHER

For Incandescent rear lamps, measure:

Positive Lead	Measurement / Action	Negative Lead
C242B-11	Courtesy of FORD MOTOR COMPANY	C242B-2

For LED rear lamps, measure:

Positive Lead	Measurement / Action	Negative Lead
C242B-11	Courtesy of FORD MOTOR COMPANY	C242B-2

Is the resistance greater than 10, 000 ohms?

Yes

GO to Z7

No	REPAIR the circuits.

Z5 CHECK FOR DTC (DIAGNOSTIC TROUBLE CODE) B15ED:15 WITH THE SODR (SIDE OBSTACLE DETECTION CONTROL MODULE RH) CIRCUITS JUMPERED TOGETHER

Ignition OFF.

For Incandescent rear lamps.

Disconnect: SODR C415B.

For LED rear lamps.

Disconnect: SODR C4484.

For Incandescent rear lamps, Connect:

Lead 1	Measurement / Action	Lead 2
C415B-1	Courtesy of FORD MOTOR COMPANY	C415B-2

For LED rear lamps, Connect:

Lead 1	Measurement / Action	Lead 2
C4484-8	Courtesy of FORD MOTOR COMPANY	C4484-5

Ignition ON.

Using a diagnostic scan tool, clear the IPMA Diagnostic Trouble Codes (DTCs).

Perform the IPMA self-test.

Is DTC B15ED:14 present?

Yes	REMOVE the fused jumper wire. INSTALL a new SODR. REFER to: Side Obstacle Detection Control Module .

No	REMOVE the fused jumper wire. GO to Z6

Z6 CHECK THE IPMA (IMAGE PROCESSING MODULE A) SODR (SIDE OBSTACLE DETECTION CONTROL MODULE RH) CIRCUITS FOR AN OPEN

Ignition OFF.

Disconnect: IPMA C242B.

For Incandescent rear lamps, measure:

Positive Lead	Measurement / Action	Negative Lead
C242B-11	Courtesy of FORD MOTOR COMPANY	C415B-1
C242B-2	Courtesy of FORD MOTOR COMPANY	C415B-2

For LED rear lamps, measure:

Positive Lead	Measurement / Action	Negative Lead
C242B-11	Courtesy of FORD MOTOR COMPANY	C4484-8
C242B-2	Courtesy of FORD MOTOR COMPANY	C4484-5

Are the resistances less than 3 ohms?

Yes

GO to Z7

No	REPAIR the affected circuit.

Z7 CHECK FOR CORRECT IPMA (IMAGE PROCESSING MODULE A) OPERATION

Disconnect and inspect IPMA connector.

Repair:
- corrosion (install new connector or terminals - clean module pins)
- damaged or bent pins - install new terminals/pins
- pushed-out pins - install new pins as necessary

Reconnect the IPMA connector. Make sure it seats and latches correctly.

Operate the system to determine if the concern is still present.

Is the concern still present?

Yes	CHECK OASIS for any applicable service articles: TSB, GSB, SSM or FSA. If a service article exists for this concern, DISCONTINUE this test and FOLLOW the service article instructions. If no service articles address this concern, INSTALL a new IPMA REFER to: Image Processing Module A (IPMA) .

No	The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.