LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2022 >> Transit Connect Titanium, Gas/Ethanol >> Repair and Diagnosis >> External Pages >> Different car >> Section 716 (Side And Rear Vision) >> Diagnosis And Testing >> Blind Spot Information System >> Pinpoint Tests >> Pinpoint Test U: DTC (Diagnostic Trouble Code) U3000:41, U3000:42, U3000:44 Or U3000:49

Pinpoint Test U: DTC (Diagnostic Trouble Code) U3000:41, U3000:42, U3000:44 Or U3000:49

WARNING: This page is about a different car, the 2021 Ford F-150. However, it is still accessible from the selected car via links, so may be relevant.
  1. Normal Operation and Fault Conditions 

    REFER to: Blind Spot Information System - System Operation and Component Description .

    DTC Fault Trigger Conditions 

    DTC Description Fault Trigger Condition
    SODCMC U3000:41 Control Module: General Checksum Failure This continuous memory DTC sets when the SODCMC start operation and all preconditions in test run / pass fail criteria are met and invalid checksum values are calculated.
    SODCMD U3000:41 Control Module: General Checksum Failure This continuous memory DTC sets when the SODCMD start operation and all preconditions in test run / pass fail criteria are met and invalid checksum values are calculated.
    SODL U3000:41 Control Module: General Checksum Failure This continuous memory DTC sets when the SODL start operation and all preconditions in test run / pass fail criteria are met and invalid checksum values are calculated.
    SODR U3000:41 Control Module: General Checksum Failure This continuous memory DTC sets when the SODR start operation and all preconditions in test run / pass fail criteria are met and invalid checksum values are calculated.
    SODCMC U3000:42 Control Module: General Memory Failure This continuous memory DTC sets when the SODCMC start operation and all preconditions in test run / pass fail criteria are met and detects an internal memory failure.
    SODCMD U3000:42 Control Module: General Memory Failure This continuous memory DTC sets when the SODCMD start operation and all preconditions in test run / pass fail criteria are met and detects an internal memory failure.
    SODL U3000:42 Control Module: General Memory Failure This continuous memory DTC sets when the SODL start operation and all preconditions in test run / pass fail criteria are met and detects an internal memory failure.
    SODR U3000:42 Control Module: General Memory Failure This continuous memory DTC sets when the SODR start operation and all preconditions in test run / pass fail criteria are met and detects an internal memory failure.
    SODCMC U3000:44 Control Module: Data Memory Failure This continuous memory DTC sets when the SODCMC start operation and all preconditions in test run / pass fail criteria are met and detects a RAM memory failure.
    SODCMD U3000:44 Control Module: Data Memory Failure This continuous memory DTC sets when the SODCMD start operation and all preconditions in test run / pass fail criteria are met and detects a RAM memory failure.
    SODL U3000:44 Control Module: Data Memory Failure This continuous memory DTC sets when the SODL start operation and all preconditions in test run / pass fail criteria are met and detects a RAM memory failure.
    SODR U3000:44 Control Module: Data Memory Failure This continuous memory DTC sets when the SODR start operation and all preconditions in test run / pass fail criteria are met and detects a RAM memory failure.
    SODCMC U3000:49 Control Module: Internal Electronic Failure This continuous memory DTC sets when the SODCMC start operation and all preconditions in test run / pass fail criteria are met and detects an internal electronic failure.
    SODCMD U3000:49 Control Module: Internal Electronic Failure This continuous memory DTC sets when the SODCMD start operation and all preconditions in test run / pass fail criteria are met and detects an internal electronic failure.
    SODL U3000:49 Control Module: Internal Electronic Failure This continuous memory DTC sets when the SODL start operation and all preconditions in test run / pass fail criteria are met and detects an internal electronic failure.
    SODR U3000:49 Control Module: Internal Electronic Failure This continuous memory DTC sets when the SODR start operation and all preconditions in test run / pass fail criteria are met and detects an internal electronic failure.

    Possible Sources 

    • SODCMC
    • SODCMD
    • SODL
    • SODR

  2. Diagnostic steps are not provided for this symptom or DTC. REFER to: Diagnostic Methods 

scientia non olet · About LEMON Manuals