Pinpoint Test AO: P0C5F

WARNING: This page is about a different car, the 2021 Ford F-150. However, it is still accessible from the selected car via links, so may be relevant.

Normal Operation and Fault Conditions

REFER to: Electric Powertrain Control - Component Location .

DTC Fault Trigger Conditions

DTC	Description	Fault Trigger Condition
SOBDMC P0C5F:00	Drive Motor "B" Position Sensor Circuit "B": No Sub Type Information	This DTC sets when an open circuit is detected in the generator resolver circuit.

Possible Sources

Wiring, terminals or connectors
Inverter System Controller (ISC) calibration

AO1 CHECK THE INVERTER SYSTEM CONTROLLER (ISC) CALIBRATION LEVEL

NOTE: Wiring overlays or repinning of circuits are NOT appropriate for DTC P0C5F due to risk of hardware damage.
- Verify the Inverter System Controller (ISC) is at the latest calibration level.
Is the Inverter System Controller (ISC) at the latest calibration level?

Yes GO to AO2

No UPDATE the Inverter System Controller (ISC) to the latest calibration level.

AO2 CHECK FOR DTC (DIAGNOSTIC TROUBLE CODE) P0C5F

Ignition ON.

Using a diagnostic scan tool, retrieve all Inverter System Controller (ISC) DTCs.

Was DTC P0C5F read from the Inverter System Controller (ISC)?

Yes

GO to AO3

No	The system is operating correctly at this time. The DTC may have been set due to high network traffic or an intermittent fault condition.

AO3 VISUAL INSPECTION OF THE LOW VOLTAGE SYSTEM
- Ignition OFF.
- Remove the high voltage traction battery service disconnect plug.
- Visually inspect all the low voltage cables.
- Make sure all the low voltage connectors are correctly and securely connected.
- Examine all the low voltage cables and connectors for damaged, burned or overheated insulation and loose or broken connections.
Is a concern present?

Yes REPAIR as necessary. CLEAR the DTCs and REPEAT the self-test.

No GO to AO4

AO4 CHECK THE GS2 CIRCUIT FOR AN OPEN

Disconnect Inverter System Controller (ISC) C1458A.

Disconnect Transmission Sensor Speed Resolver C1280.

Measure and record:

Positive Lead	Measurement / Action	Negative Lead
C1458A-A2	Courtesy of FORD MOTOR COMPANY	C1280-1

Is the resistance less than 5 ohms?

Yes

GO to AO5

No	REPLACE the harness. CLEAR the DTCs and REPEAT the self-test.

AO5 CHECK THE GS4 CIRCUIT FOR AN OPEN

Measure and record:

Positive Lead	Measurement / Action	Negative Lead
C1458A-B2	Courtesy of FORD MOTOR COMPANY	C1280-5

Is the resistance less than 5 ohms?

Yes

GO to AO6

No	REPLACE the harness. CLEAR the DTCs and REPEAT the self-test.

AO6 CHECK FOR CORRECT INVERTER SYSTEM CONTROLLER (ISC) OPERATION

Ignition OFF.

Inspect all Inverter System Controller (ISC) connectors.

Repair:
- corrosion (install new connector or terminals - clean module pins)
- damaged or bent pins - install new terminals/pins
- pushed-out pins - install new pins as necessary

Reconnect all of the previously disconnected connectors. Make sure they seat and latch correctly.

Ignition ON.

Using a diagnostic scan tool, clear all Inverter System Controller (ISC) DTCs.

Using a diagnostic scan tool, retrieve all Inverter System Controller (ISC) DTCs.

Is DTC P0C5F present?

Yes

CHECK OASIS for any applicable service articles: TSB, GSB, SSM or FSA. If a service article exists for this concern, DISCONTINUE this test and FOLLOW the service article instructions. If no service articles address this concern, REFER to: Powertrain Control Module (PCM) Input and Output Controls . Pinpoint Test Z.

No	The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.