Fuel Rail Supply Tube RH: Installation

WARNING: This page is about a different car, the 2021 Ford F-150. However, it is still accessible from the selected car via links, so may be relevant.

NOTE: Make sure that a new fuel rail supply tube is installed.

Install a new fuel rail supply tube then, tighten the fuel supply tube fittings finger tight at this stage.

Courtesy of FORD MOTOR COMPANY
Install the fuel rail supply tube bracket, then install and tighten bolt.
Torque: 89 lb.in (10 Nm)

Courtesy of FORD MOTOR COMPANY
Install a new fuel rail supply tube, then install the bracket bolt. Tighten the fuel supply tube fittings and the bracket bolt finger tight at this stage. Tighten in the following 6 stages.
Torque:Stage 1: Tighten the fuel injection pump fitting to: : 89 lb.in (10 Nm); Stage 2: Tighten the fuel rail fitting to: : 89 lb.in (10 Nm); Stage 3: Tighten the fuel injection pump fitting to: : 142 lb.in (16 Nm); Stage 4: Tighten the fuel rail fitting to: : 142 lb.in (16 Nm); Stage 5: Tighten the fuel injection pump fitting an additional: : 50 deg.; Stage 6: Tighten the fuel rail fitting an additional: : 50 deg.

Courtesy of FORD MOTOR COMPANY
Install the insulator.

Courtesy of FORD MOTOR COMPANY
Attach the wire harness and the coolant hose retainers.

Courtesy of FORD MOTOR COMPANY
Attach the wire harness retainers, then install and tighten the wire harness bolt.
Torque: 89 lb.in (10 Nm)

Courtesy of FORD MOTOR COMPANY
1. Install the vacuum tube assembly, then attach the vacuum reservoir retainers.
2. Attach the valve to the bracket.
3. Connect the electrical connector, then connect the quick release coupling. Refer to: Quick Release Coupling (310-00 Fuel System - General Information - 3.0L Power Stroke Diesel).
4. Attach the vacuum tube retainers, then connect the vacuum hose at the EGR.
Courtesy of FORD MOTOR COMPANY
Attach the wiring harness bracket to the rear engine lifting eye and to the transmission case.

Courtesy of FORD MOTOR COMPANY
Install the right front fender splash shield. Refer to: Fender Splash Shield .
Install the secondary fuel filter, then install and tighten the bolt.
Torque: 89 lb.in (10 Nm)

Courtesy of FORD MOTOR COMPANY
1. If equipped, attach the vacuum tube retainers.
2. If equipped, connect the quick release coupling. Refer to: Quick Release Coupling (310-00 Fuel System - General Information - 3.0L Power Stroke Diesel).
Courtesy of FORD MOTOR COMPANY
Connect the fuel tube assembly quick release coupling. Refer to: Quick Release Coupling (310-00 Fuel System - General Information - 3.0L Power Stroke Diesel).

Courtesy of FORD MOTOR COMPANY
1. Install fuel supply tube assembly, then install and tighten the bolt.
  Torque: 17 lb.ft (23 Nm)
2. Connect the fuel supply tube assembly quick release couplings. Refer to: Quick Release Coupling (310-00 Fuel System - General Information - 3.0L Power Stroke Diesel).
Courtesy of FORD MOTOR COMPANY
Connect the fuel supply tube assembly electrical connector, then attach the wire retainer.

Courtesy of FORD MOTOR COMPANY
Connect the quick release couplings, then attach the fuel tube retainers. Refer to: Quick Release Coupling (310-00 Fuel System - General Information - 3.0L Power Stroke Diesel).

Courtesy of FORD MOTOR COMPANY
Connect the battery negative cable. Refer to: Battery Disconnect and Connect .
Bleed the fuel system. Refer to: Fuel System Bleeding .
Install the engine appearance cover bracket, then install and tighten the retainers.
Torque: 44 lb.in (5 Nm)

Courtesy of FORD MOTOR COMPANY
Install the engine appearance cover.

Courtesy of FORD MOTOR COMPANY