Diagnostic Trouble Code (DTC) Chart
WARNING: This page is about a different car, the 2021 Ford F-150. However, it is still accessible from the selected car via links, so may be relevant.
Diagnostics in this article assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .
Diagnostic Trouble Code Chart
| Module | DTC | Description | Action |
|---|---|---|---|
| ACM | B150C:01 | Automobile Audio Bus (A2B) Node 1: General Electrical Failure | GO to Pinpoint Test C |
| ACM | B150C:11 | Automobile Audio Bus (A2B) Node 1: Circuit Short To Ground | GO to Pinpoint Test C |
| ACM | B150C:12 | Automobile Audio Bus (A2B) Node 1: Circuit Short To Battery | GO to Pinpoint Test C |
| ACM | B150C:13 | Automobile Audio Bus (A2B) Node 1: Circuit Open | GO to Pinpoint Test C |
| ACM | B150C:55 | Automobile Audio Bus (A2B) Node 1: Not Configured | GO to Pinpoint Test C |
| ACM | B150C:87 | Automobile Audio Bus (A2B) Node 1: Missing Message | GO to Pinpoint Test C |
| ACM | B150C:8F | Automobile Audio Bus (A2B) Node 1: Erratic | GO to Pinpoint Test C |
| ACM | B150C:95 | Automobile Audio Bus (A2B) Node 1: Incorrect Assembly | GO to Pinpoint Test C |
| ACM | B1511:01 | Automobile Audio Bus (A2B) Master Node: General Electrical Failure | GO to Pinpoint Test C |
| ACM | B1511:11 | Automobile Audio Bus (A2B) Master Node: Circuit Short To Ground | GO to Pinpoint Test C |
| ACM | B1511:12 | Automobile Audio Bus (A2B) Master Node: Circuit Short To Battery | GO to Pinpoint Test C |
| ACM | B1511:13 | Automobile Audio Bus (A2B) Master Node: Circuit Open | GO to Pinpoint Test C |
| ACM | B1511:95 | Automobile Audio Bus (A2B) Master Node: Incorrect Assembly | GO to Pinpoint Test C |
| ACM | B1A01:01 | Speaker #1: General Electrical Failure | GO to Pinpoint Test F |
| ACM | B1A01:01 | Speaker #1: General Electrical Failure | GO to Pinpoint Test H |
| ACM | B1A01:11 | Speaker #1: Circuit Short To Ground | GO to Pinpoint Test F |
| ACM | B1A01:11 | Speaker #1: Circuit Short To Ground | GO to Pinpoint Test H |
| ACM | B1A01:12 | Speaker #1: Circuit Short To Battery | GO to Pinpoint Test F |
| ACM | B1A01:12 | Speaker #1: Circuit Short To Battery | GO to Pinpoint Test H |
| ACM | B1A01:13 | Speaker #1: Circuit Open | GO to Pinpoint Test F |
| ACM | B1A01:13 | Speaker #1: Circuit Open | GO to Pinpoint Test H |
| ACM | B1A02:01 | Speaker #2: General Electrical Failure | GO to Pinpoint Test F |
| ACM | B1A02:01 | Speaker #2: General Electrical Failure | GO to Pinpoint Test H |
| ACM | B1A02:11 | Speaker #2: Circuit Short To Ground | GO to Pinpoint Test F |
| ACM | B1A02:11 | Speaker #2: Circuit Short To Ground | GO to Pinpoint Test H |
| ACM | B1A02:12 | Speaker #2: Circuit Short To Battery | GO to Pinpoint Test F |
| ACM | B1A02:12 | Speaker #2: Circuit Short To Battery | GO to Pinpoint Test H |
| ACM | B1A02:13 | Speaker #2: Circuit Open | GO to Pinpoint Test F |
| ACM | B1A02:13 | Speaker #2: Circuit Open | GO to Pinpoint Test H |
| ACM | B1A03:01 | Speaker #3: General Electrical Failure | GO to Pinpoint Test F |
| ACM | B1A03:01 | Speaker #3: General Electrical Failure | GO to Pinpoint Test G |
| ACM | B1A03:01 | Speaker #3: General Electrical Failure | GO to Pinpoint Test H |
| ACM | B1A03:11 | Speaker #3: Circuit Short To Ground | GO to Pinpoint Test F |
| ACM | B1A03:11 | Speaker #3: Circuit Short To Ground | GO to Pinpoint Test G |
| ACM | B1A03:11 | Speaker #3: Circuit Short To Ground | GO to Pinpoint Test H |
| ACM | B1A03:12 | Speaker #3: Circuit Short To Battery | GO to Pinpoint Test F |
| ACM | B1A03:12 | Speaker #3: Circuit Short To Battery | GO to Pinpoint Test G |
| ACM | B1A03:12 | Speaker #3: Circuit Short To Battery | GO to Pinpoint Test H |
| ACM | B1A03:13 | Speaker #3: Circuit Open | GO to Pinpoint Test F |
| ACM | B1A03:13 | Speaker #3: Circuit Open | GO to Pinpoint Test G |
| ACM | B1A03:13 | Speaker #3: Circuit Open | GO to Pinpoint Test H |
| ACM | B1A04:01 | Speaker #4: General Electrical Failure | GO to Pinpoint Test F |
| ACM | B1A04:01 | Speaker #4: General Electrical Failure | GO to Pinpoint Test G |
| ACM | B1A04:01 | Speaker #4: General Electrical Failure | GO to Pinpoint Test H |
| ACM | B1A04:11 | Speaker #4: Circuit Short To Ground | GO to Pinpoint Test F |
| ACM | B1A04:11 | Speaker #4: Circuit Short To Ground | GO to Pinpoint Test G |
| ACM | B1A04:11 | Speaker #4: Circuit Short To Ground | GO to Pinpoint Test H |
| ACM | B1A04:12 | Speaker #4: Circuit Short To Battery | GO to Pinpoint Test F |
| ACM | B1A04:12 | Speaker #4: Circuit Short To Battery | GO to Pinpoint Test G |
| ACM | B1A04:12 | Speaker #4: Circuit Short To Battery | GO to Pinpoint Test H |
| ACM | B1A04:13 | Speaker #4: Circuit Open | GO to Pinpoint Test F |
| ACM | B1A04:13 | Speaker #4: Circuit Open | GO to Pinpoint Test G |
| ACM | B1A04:13 | Speaker #4: Circuit Open | GO to Pinpoint Test H |
| ACM | B1A06:01 | Speaker #6: General Electrical Failure | GO to Pinpoint Test F |
| ACM | B1A06:11 | Speaker #6: Circuit Short To Ground | GO to Pinpoint Test F |
| ACM | B1A06:12 | Speaker #6: Circuit Short To Battery | GO to Pinpoint Test F |
| ACM | B1A06:13 | Speaker #6: Circuit Open | GO to Pinpoint Test F |
| ACM | B1A56:11 | Antenna: Circuit Short To Ground | GO to Pinpoint Test A |
| ACM | B1A56:15 | Antenna: Circuit Short To Battery or Open | GO to Pinpoint Test A |
| ACM | B1A89:11 | Satellite Antenna: Circuit Short To Ground | GO to Pinpoint Test B |
| ACM | B1A89:13 | Satellite Antenna: Circuit Open | GO to Pinpoint Test B |
| ACM | U0100:00 | Lost Communication with ECM/PCM "A": No Sub Type Information | GO to Pinpoint Test AB |
| ACM | U0121:00 | Lost Communication With Anti-Lock Brake System (ABS) Control Module: No Sub Type Information | GO to Pinpoint Test AC |
| ACM | U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test AD |
| ACM | U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to Pinpoint Test AF |
| ACM | U0198:00 | Lost Communication With Telematic Control Module: No Sub Type Information | GO to Pinpoint Test AH |
| ACM | U0238:00 | Lost Communication With Digital Audio Control Module "D": No Sub Type Information | GO to Pinpoint Test AI |
| ACM | U0253:00 | Lost Communication With Accessory Protocol Interface Module: No Sub Type Information | GO to Pinpoint Test AJ |
| ACM | U201A:51 | Control Module Main Calibration Data: Not Programmed | GO to Pinpoint Test AO |
| ACM | U201B:04 | Control Module Calibration Data #2: System Internal Failure | GO to Pinpoint Test AO |
| ACM | U201B:51 | Control Module Calibration Data #2: Not Programmed | GO to Pinpoint Test AO |
| ACM | U201B:55 | Control Module Calibration Data #2: Not Configured | GO to Pinpoint Test AO |
| ACM | U2024:00 | Control Module Cal-Config Data: No Sub Type Information | GO to Pinpoint Test AO |
| ACM | U2024:57 | Control Module Cal-Config Data: Invalid / Incompatible Software Component | GO to Pinpoint Test AO |
| ACM | U2026:54 | Control Module Cal-Config Data #3: Missing Calibration | GO to Pinpoint Test AO |
| ACM | U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test AO |
| ACM | U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | GO to Pinpoint Test AO |
| ACM | U3000:41 | Control Module: General Checksum Failure | GO to Pinpoint Test AP |
| ACM | U3000:42 | Control Module: General Memory Failure | GO to Pinpoint Test AP |
| ACM | U3000:92 | Control Module: Performance or Incorrect Operation | GO to Pinpoint Test AP |
| ACM | U3000:94 | Control Module: Unexpected Operation | GO to Pinpoint Test AP |
| ACM | U3000:96 | Control Module: Component Internal Failure | GO to Pinpoint Test AP |
| ACM | U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test AK |
| ACM | U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test AL |
| APIM | B1087:01 | LIN Bus "A": General Electrical Failure | GO to Pinpoint Test L |
| APIM | B108E:01 | Display: General Electrical Failure | GO to Pinpoint Test O |
| APIM | B108E:02 | Display: General Signal Failure | GO to Pinpoint Test O |
| APIM | B108E:4A | Display: Incorret Component Installed | GO to Pinpoint Test O |
| APIM | B108E:4B | Display: Over Temperature | GO to Pinpoint Test O |
| APIM | B108E:87 | Display: Missing Message | GO to Pinpoint Test O |
| APIM | B119F:01 | GPS Antenna: General Electrical Failure | GO to Pinpoint Test W |
| APIM | B119F:13 | GPS Antenna: Circuit Open | GO to Pinpoint Test W |
| APIM | B1252:11 | USB Port: Circuit Short to Ground | GO to Pinpoint Test S |
| APIM | B1252:13 | USB Port: Circuit Open | GO to Pinpoint Test S |
| APIM | B14FD:11 | External Media Control Connectivity: Circuit Short To Ground | GO to Pinpoint Test S |
| APIM | B156D:54 | TCU Customer Connectivity Settings Synchronization With HMI: Missing Calibration | GO to Pinpoint Test AU |
| APIM | B156D:89 | TCU Customer Connectivity Settings Synchronization With HMI: Data Transfer Failure | GO to Pinpoint Test AU |
| APIM | B15EB:57 | Consumer Apps: Invalid / Incompatible Software Component | GO to Pinpoint Test AU |
| APIM | B1D79:11 | Microphone Input: Circuit Short To Ground | GO to Pinpoint Test Q |
| APIM | B1D79:12 | Microphone Input: Circuit Short To Battery | GO to Pinpoint Test Q |
| APIM | B1D79:13 | Microphone Input: Circuit Open | GO to Pinpoint Test Q |
| APIM | U0100:00 | Lost Communication with ECM/PCM "A": No Sub Type Information | GO to Pinpoint Test AB |
| APIM | U0121:00 | Lost Communication With Anti-Lock Brake System (ABS) Control Module: No Sub Type Information | GO to Pinpoint Test AS |
| APIM | U0121:55 | Lost Communication With Anti-Lock Brake System (ABS) Control Module "A": Not Configured | GO to Pinpoint Test AU |
| APIM | U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test AS |
| APIM | U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | GO to Pinpoint Test AS |
| APIM | U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to Pinpoint Test AS |
| APIM | U0159:00 | Lost Communication With Parking Assist Control Module "A": No Sub Type Information | GO to Pinpoint Test AS |
| APIM | U0162:00 | Lost Communication With Navigation Display Module: No Sub Type Information | GO to Pinpoint Test O |
| APIM | U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to Pinpoint Test AS |
| APIM | U0198:00 | Lost Communication With Telematic Control Module: No Sub Type Information | GO to Pinpoint Test AS |
| APIM | U0208:00 | Lost Communication With "Seat Control Module A": No Sub Type Information | GO to Pinpoint Test AS |
| APIM | U020C:00 | Lost Communication with Wireless Accessory Charging Module "A": No Sub Type Information | GO to Pinpoint Test AS |
| APIM | U0212:00 | Lost Communication With Steering Column Control Module: No Sub Type Information | GO to Pinpoint Test AS |
| APIM | U0232:00 | Lost Communication With Side Obstacle Detection Control Module - Left: No Sub Type Information | GO to Pinpoint Test AS |
| APIM | U0233:00 | Lost Communication With Side Obstacle Detection Control Module - Right: No Sub Type Information | GO to Pinpoint Test AS |
| APIM | U0238:00 | Lost Communication With Digital Audio Control Module "D": No Sub Type Information | GO to Pinpoint Test AS |
| APIM | U023B:00 | Lost Communication With Image Processing Module B: No Sub Type Information | GO to Pinpoint Test AS |
| APIM | U024B:00 | Lost Communication with Seat Control Module "G": No Sub Type Information | GO to Pinpoint Test AS |
| APIM | U024C:00 | Lost Communication with Seat Control Module "H": No Sub Type Information | GO to Pinpoint Test AS |
| APIM | U0293:00 | Lost Communication With Hybrid/EV Powertrain Control Module: No Sub Type Information | GO to Pinpoint Test AS |
| APIM | U0415:00 | Invalid Data Received From Anti-Lock Brake System (ABS) Control Module: No Sub Type Information | GO to Pinpoint Test AT |
| APIM | U0415:94 | Invalid Data Received From Anti-Lock Brake System (ABS) Control Module: Unexpected Operation | GO to Pinpoint Test AT |
| APIM | U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | GO to Pinpoint Test AT |
| APIM | U0452:00 | Invalid Data Received From Restraints Control Module: No Sub Type Information | GO to Pinpoint Test AT |
| APIM | U1A00:87 | Private Communication Network: Missing Message | GO to Pinpoint Test B |
| APIM | U2013:01 | Switch Pack: General Electrical Failure | GO to Pinpoint Test L |
| APIM | U2013:16 | Switch Pack: Circuit Voltage Below Threshold | GO to Pinpoint Test L |
| APIM | U2013:17 | Switch Pack: Circuit Voltage Above Threshold | GO to Pinpoint Test L |
| APIM | U2013:63 | Switch Pack: Circuit / Component Protection Time-Out | GO to Pinpoint Test L |
| APIM | U2017:45 | Control Module Software #2: Program Memory Failure | GO to Pinpoint Test AU |
| APIM | U2017:51 | Control Module Software #2: Not Programmed | GO to Pinpoint Test AU |
| APIM | U2017:52 | Control Module Software #2: Not Activated | GO to Pinpoint Test AU |
| APIM | U2017:54 | Control Module Software #2: Missing Calibration | GO to Pinpoint Test AU |
| APIM | U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test AU |
| APIM | U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | GO to Pinpoint Test AU |
| APIM | U3000:04 | Control Module: System Internal Failure | GO to Pinpoint Test AV |
| APIM | U3000:05 | Control Module: System Programming Failure | GO to Pinpoint Test AV |
| APIM | U3000:09 | Control Module: Component Failure | GO to Pinpoint Test AV |
| APIM | U3000:41 | Control Module: General Checksum Failure | GO to Pinpoint Test AV |
| APIM | U3000:43 | Control Module: Special Memory Failure | GO to Pinpoint Test AV |
| APIM | U3000:57 | Control Module: Invalid / Incompatible Software Component | GO to Pinpoint Test AU |
| APIM | U3000:88 | Control Module: Bus Off | GO to Pinpoint Test AS |
| APIM | U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test AK |
| APIM | U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test AL |
| DSP | B13FB:11 | Audio Enable Line: Circuit Short To Ground | GO to Pinpoint Test C |
| DSP | B1A01:01 | Speaker #1: General Electrical Failure | GO to Pinpoint Test I |
| DSP | B1A01:01 | Speaker #1: General Electrical Failure | GO to Pinpoint Test J |
| DSP | B1A01:11 | Speaker #1: Circuit Short To Ground | GO to Pinpoint Test I |
| DSP | B1A01:11 | Speaker #1: Circuit Short To Ground | GO to Pinpoint Test J |
| DSP | B1A01:12 | Speaker #1: Circuit Short To Battery | GO to Pinpoint Test I |
| DSP | B1A01:12 | Speaker #1: Circuit Short To Battery | GO to Pinpoint Test J |
| DSP | B1A01:13 | Speaker #1: Circuit Open | GO to Pinpoint Test I |
| DSP | B1A01:13 | Speaker #1: Circuit Open | GO to Pinpoint Test J |
| DSP | B1A02:01 | Speaker #2: General Electrical Failure | GO to Pinpoint Test I |
| DSP | B1A02:01 | Speaker #2: General Electrical Failure | GO to Pinpoint Test J |
| DSP | B1A02:11 | Speaker #2: Circuit Short To Ground | GO to Pinpoint Test I |
| DSP | B1A02:11 | Speaker #2: Circuit Short To Ground | GO to Pinpoint Test J |
| DSP | B1A02:12 | Speaker #2: Circuit Short To Battery | GO to Pinpoint Test I |
| DSP | B1A02:12 | Speaker #2: Circuit Short To Battery | GO to Pinpoint Test J |
| DSP | B1A02:13 | Speaker #2: Circuit Open | GO to Pinpoint Test I |
| DSP | B1A02:13 | Speaker #2: Circuit Open | GO to Pinpoint Test J |
| DSP | B1A03:01 | Speaker #3: General Electrical Failure | GO to Pinpoint Test I |
| DSP | B1A03:01 | Speaker #3: General Electrical Failure | GO to Pinpoint Test K |
| DSP | B1A03:11 | Speaker #3: Circuit Short To Ground | GO to Pinpoint Test I |
| DSP | B1A03:11 | Speaker #3: Circuit Short To Ground | GO to Pinpoint Test K |
| DSP | B1A03:12 | Speaker #3: Circuit Short To Battery | GO to Pinpoint Test I |
| DSP | B1A03:12 | Speaker #3: Circuit Short To Battery | GO to Pinpoint Test K |
| DSP | B1A03:13 | Speaker #3: Circuit Open | GO to Pinpoint Test I |
| DSP | B1A03:13 | Speaker #3: Circuit Open | GO to Pinpoint Test K |
| DSP | B1A04:01 | Speaker #4: General Electrical Failure | GO to Pinpoint Test I |
| DSP | B1A04:01 | Speaker #4: General Electrical Failure | GO to Pinpoint Test J |
| DSP | B1A04:11 | Speaker #4: Circuit Short To Ground | GO to Pinpoint Test I |
| DSP | B1A04:11 | Speaker #4: Circuit Short To Ground | GO to Pinpoint Test J |
| DSP | B1A04:12 | Speaker #4: Circuit Short To Battery | GO to Pinpoint Test I |
| DSP | B1A04:12 | Speaker #4: Circuit Short To Battery | GO to Pinpoint Test J |
| DSP | B1A04:13 | Speaker #4: Circuit Open | GO to Pinpoint Test I |
| DSP | B1A04:13 | Speaker #4: Circuit Open | GO to Pinpoint Test J |
| DSP | B1A05:01 | Speaker #5: General Electrical Failure | GO to Pinpoint Test I |
| DSP | B1A05:01 | Speaker #5: General Electrical Failure | GO to Pinpoint Test J |
| DSP | B1A05:11 | Speaker #5: Circuit Short To Ground | GO to Pinpoint Test I |
| DSP | B1A05:11 | Speaker #5: Circuit Short To Ground | GO to Pinpoint Test J |
| DSP | B1A05:12 | Speaker #5: Circuit Short To Battery | GO to Pinpoint Test I |
| DSP | B1A05:12 | Speaker #5: Circuit Short To Battery | GO to Pinpoint Test J |
| DSP | B1A05:13 | Speaker #5: Circuit Open | GO to Pinpoint Test I |
| DSP | B1A05:13 | Speaker #5: Circuit Open | GO to Pinpoint Test J |
| DSP | B1A06:01 | Speaker #6: General Electrical Failure | GO to Pinpoint Test I |
| DSP | B1A06:01 | Speaker #6: General Electrical Failure | GO to Pinpoint Test J |
| DSP | B1A06:11 | Speaker #6: Circuit Short To Ground | GO to Pinpoint Test I |
| DSP | B1A06:11 | Speaker #6: Circuit Short To Ground | GO to Pinpoint Test J |
| DSP | B1A06:12 | Speaker #6: Circuit Short To Battery | GO to Pinpoint Test I |
| DSP | B1A06:12 | Speaker #6: Circuit Short To Battery | GO to Pinpoint Test J |
| DSP | B1A06:13 | Speaker #6: Circuit Open | GO to Pinpoint Test I |
| DSP | B1A06:13 | Speaker #6: Circuit Open | GO to Pinpoint Test J |
| DSP | B1A07:01 | Speaker #7: General Electrical Failure | GO to Pinpoint Test J |
| DSP | B1A07:11 | Speaker #7: Circuit Short To Ground | GO to Pinpoint Test J |
| DSP | B1A07:12 | Speaker #7: Circuit Short To Battery | GO to Pinpoint Test J |
| DSP | B1A07:13 | Speaker #7: Circuit Open | GO to Pinpoint Test J |
| DSP | B1A08:01 | Speaker #8: General Electrical Failure | GO to Pinpoint Test J |
| DSP | B1A08:11 | Speaker #8: Circuit Short To Ground | GO to Pinpoint Test J |
| DSP | B1A08:12 | Speaker #8: Circuit Short To Battery | GO to Pinpoint Test J |
| DSP | B1A08:13 | Speaker #8: Circuit Open | GO to Pinpoint Test J |
| DSP | B1A09:01 | Speaker #9: General Electrical Failure | GO to Pinpoint Test J |
| DSP | B1A09:11 | Speaker #9: Circuit Short To Ground | GO to Pinpoint Test J |
| DSP | B1A09:12 | Speaker #9: Circuit Short To Battery | GO to Pinpoint Test J |
| DSP | B1A09:13 | Speaker #9: Circuit Open | GO to Pinpoint Test J |
| DSP | B1A10:01 | Speaker #10: General Electrical Failure | GO to Pinpoint Test K |
| DSP | B1A10:11 | Speaker #10: Circuit Short To Ground | GO to Pinpoint Test K |
| DSP | B1A10:12 | Speaker #10: Circuit Short To Battery | GO to Pinpoint Test K |
| DSP | B1A10:13 | Speaker #10: Circuit Open | GO to Pinpoint Test K |
| DSP | U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test AD |
| DSP | U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to Pinpoint Test AF |
| DSP | U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to Pinpoint Test AG |
| DSP | U0198:00 | Lost Communication With Telematic Control Module: No Sub Type Information | GO to Pinpoint Test AH |
| DSP | U0253:00 | Lost Communication With Accessory Protocol Interface Module: No Sub Type Information | GO to Pinpoint Test AJ |
| DSP | U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | GO to Pinpoint Test AN |
| DSP | U0423:00 | Invalid Data Received from Instrument Panel Cluster: No Sub Type Information | GO to Pinpoint Test AN |
| DSP | U201A:51 | Control Module Main Calibration Data: Not Programmed | GO to Pinpoint Test AO |
| DSP | U2024:41 | Control Module Cal-Config Data: General Checksum Failure | GO to Pinpoint Test AO |
| DSP | U2024:48 | Control Module Cal-Config Data: Supervision Software | GO to Pinpoint Test AO |
| DSP | U2024:51 | Control Module Cal-Config Data: Not Programmed | GO to Pinpoint Test AO |
| DSP | U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test AO |
| DSP | U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | GO to Pinpoint Test AO |
| DSP | U3000:41 | Control Module: General Checksum Failure | GO to Pinpoint Test AP |
| DSP | U3000:42 | Control Module: General Memory Failure | GO to Pinpoint Test AP |
| DSP | U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test AK |
| DSP | U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test AL |
| SCCM | B137F:11 | Steering Wheel Left Switch Pack: Circuit Short To Ground | GO to Pinpoint Test M |
| SCCM | B137F:13 | Steering Wheel Left Switch Pack: Circuit Open | GO to Pinpoint Test M |
| SCCM | B137F:4A | Steering Wheel Left Switch Pack: Incorrect Component Installed | GO to Pinpoint Test M |
| SCCM | B137F:96 | Steering Wheel Left Switch Pack: Component Internal Failure | GO to Pinpoint Test M |
| SCCM | B137F:9E | Steering Wheel Left Switch Pack: Stuck On | GO to Pinpoint Test M |
| SCCM | B1380:11 | Steering Wheel Right Switch Pack: Circuit Short To Ground | GO to Pinpoint Test M |
| SCCM | B1380:13 | Steering Wheel Right Switch Pack: Circuit Open | GO to Pinpoint Test M |
| SCCM | B1380:4A | Steering Wheel Right Switch Pack: Incorrect Component Installed | GO to Pinpoint Test M |
| SCCM | B1380:96 | Steering Wheel Right Switch Pack: Component Internal Failure | GO to Pinpoint Test M |
| SCCM | B1380:9E | Steering Wheel Right Switch Pack: Stuck On | GO to Pinpoint Test M |
| SECM | B137F:11 | Steering Wheel Left Switch Pack: Circuit Short To Ground | GO to Pinpoint Test N |
| SECM | B137F:17 | Steering Wheel Left Switch Pack: Circuit Voltage Above Threshold | GO to Pinpoint Test N |
| SECM | B137F:2A | Steering Wheel Left Switch Pack: Signal Stuck In Range | GO to Pinpoint Test N |
| SECM | B137F:4A | Steering Wheel Left Switch Pack: Incorrect Component Installed | GO to Pinpoint Test N |
| SECM | B1380:11 | Steering Wheel Right Switch Pack: Circuit Short To Ground | GO to Pinpoint Test N |
| SECM | B1380:17 | Steering Wheel Right Switch Pack: Circuit Voltage Above Threshold | GO to Pinpoint Test N |
| SECM | B1380:2A | Steering Wheel Right Switch Pack: Signal Stuck In Range | GO to Pinpoint Test N |
| SECM | B1380:4A | Steering Wheel Right Switch Pack: Incorrect Component Installed | GO to Pinpoint Test N |
| TCU | B116C:04 | External SIM Cable/SIM Card: System Internal Failure | GO to Pinpoint Test AP |
| TCU | B116C:57 | External SIM Cable/SIM Card: Invalid / Incompatible Software Component | GO to Pinpoint Test AP |
| TCU | B119F:11 | GPS Antenna: Circuit Short To Ground | GO to Pinpoint Test V |
| TCU | B119F:13 | GPS Antenna: Circuit Open | GO to Pinpoint Test V |
| TCU | B1246:11 | GSM (Group System for Mobile) Antenna: Circuit Short To Ground | GO to Pinpoint Test X |
| TCU | B1246:13 | GSM (Group System for Mobile) Antenna: Circuit Open | GO to Pinpoint Test X |
| TCU | B1D55:11 | Antenna #2: Circuit Short To Ground | GO to Pinpoint Test Y |
| TCU | B1D55:13 | Antenna #2: Circuit Open | GO to Pinpoint Test Y |
| TCU | U0001:09 | High Speed CAN Communication Bus: Component Failure | GO to Pinpoint Test AM |
| TCU | U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test AD |
| TCU | U0146:09 | Lost Communication With Serial Data Gateway "A": Component Failure | GO to Pinpoint Test AE |
| TCU | U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | GO to Pinpoint Test AN |
| TCU | U1A01:09 | Communication Link: Component Failure | GO to Pinpoint Test AO |
| TCU | U1A01:92 | Communication Link: Performance or Incorrect Operation | GO to Pinpoint Test AP |
| TCU | U1A01:93 | Communication Link: No Operation | GO to Pinpoint Test AP |
| TCU | U1A4B:52 | Control Module Processor B: Not Activated | GO to Pinpoint Test AP |
| TCU | U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test AO |
| TCU | U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | GO to Pinpoint Test AO |
| TCU | U2101:56 | Control Module Configuration Incompatible: Invalid / Incompatible Configuration | GO to Pinpoint Test AO |
| TCU | U2200:00 | Control Module Configuration Memory Corrupt: No Sub Type Information | GO to Pinpoint Test AP |
| TCU | U3000:04 | Control Module: System Internal Failure | GO to Pinpoint Test AQ |
| TCU | U3000:09 | Control Module: Component Failure | GO to Pinpoint Test AP |
| TCU | U3000:43 | Control Module: Special Memory Failure | GO to Pinpoint Test AP |
| TCU | U3000:57 | Control Module: Invalid / Incompatible Component | GO to Pinpoint Test AR |
| TCU | U3000:96 | Control Module: Component Internal Failure | GO to Pinpoint Test AP |
| TCU | U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test AK |
| TCU | U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test AL |