LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2022 >> Transit Connect Titanium, Gas/Ethanol >> Repair and Diagnosis >> External Pages >> Different car >> Section 601 (Instrumentation, Message Center And Warning Chimes (2 Of 2)) >> Diagnosis And Testing >> Instrumentation, Message Center and Warning Chimes >> Pinpoint Tests >> Pinpoint Test AY: The Stability-Traction Control Disabled (Sliding Car Off Icon) Indicator Or RTT (RECONFIGURABLE Telltale) Indicator Is Never Or Always On

Pinpoint Test AY: The Stability-Traction Control Disabled (Sliding Car Off Icon) Indicator Or RTT (RECONFIGURABLE Telltale) Indicator Is Never Or Always On

WARNING: This page is about a different car, the 2021 Ford F-150. However, it is still accessible from the selected car via links, so may be relevant.
  1. Normal Operation and Fault Conditions 

    See Stability-Traction Control Disabled (Sliding Car OFF Icon). REFER to: Instrument Panel Cluster (IPC) - System Operation and Component Description .

    If the traction control off indicator request is missing or invalid for less than 5 seconds, the IPC defaults the stability-traction control disabled (sliding car OFF icon) indicator or RTT indicator to the last indication state (on or off), based upon the last message received.

    If the IPC does not receive the traction control off indicator request for 5 seconds or longer, the IPC defaults the stability-traction control disabled (sliding car OFF icon) indicator or RTT off.

    When a MyKey® programmed key is in use and the AdvanceTrac® on feature is configured always on, the traction control system cannot be disabled and the traction control indicator does not turn on when the traction control disable button is pressed. The traction control indicator still functions correctly to indicate a traction control system fault and a traction control active event.

    Possible Sources 

    • MyKey® programmed key in use
    • Stability-traction control system concern
    • Stability-traction control system cannot be disabled
    • Communication concern
    • GWM
    • IPC

  2. AY1 IDENTIFY THE IPC (INSTRUMENT PANEL CLUSTER) LEVEL

    Is the vehicle equipped with a 4-inch display IPC? 

    Yes  GO to  AY3
    No  GO to  AY2

  3. AY2 CHECK THE MESSAGE CENTER OPERATION

    • Ignition ON.

    • Close all doors and hood.

    • Clear all message center warnings by pressing the OK button for each warning present.

    • Monitor the door ajar RTT warning indicator.

    • Open the driver door.

    • Clear the message center popup warning.

    • Monitor the door ajar RTT warning indicator.

    Is the door ajar RTT warning indicator off with the door closed, and on with the door open? 

    Yes  GO to  AY4
    No  GO to Pinpoint Test A 

  4. AY3 PERFORM THE IPC (INSTRUMENT PANEL CLUSTER) INDICATOR LAMP CONTROL ACTIVE COMMAND

    • Using a diagnostic scan tool, view the IPC Parameter Identifications (PIDs).

    • Access the IPC and control the ALL_LAMPSPID

    • Command the stability-traction control disabled (sliding car OFF icon) indicator on and off while observing the indicator.

    Does the stability-traction control disabled (sliding car OFF icon) indicator illuminate when commanded on and turn off when commanded off? 

    Yes  GO to  AY4
    No  GO to  AY8

  5. AY4 PERFORM THE IPC (INSTRUMENT PANEL CLUSTER) SELF-TEST

    • Using a diagnostic scan tool, perform the IPC self-test.

    Are any Diagnostic Trouble Codes (DTCs) recorded? 

    Yes  REFER to the IPCDTC Chart.
    No  GO to  AY5

  6. AY5 CHECK THE GWM (GATEWAY MODULE A) DIAGNOSTIC TROUBLE CODES (DTCS)

    • Using a diagnostic scan tool, check the GWM Continuous Memory Diagnostic Trouble Codes (DTCs).

    Are any Diagnostic Trouble Codes (DTCs) recorded? 

    Yes  REFER to: Controller Area Network (CAN) Module Communications Network .
    No  GO to  AY6

  7. AY6 CHECK FOR THE KEY TYPE

    • Check if the key is a MyKey® programmed key or an administrator key. Refer to the Owner's Literature.

    Is the key an administrator key? 

    Yes  GO to  AY7
    No  DIAGNOSE the stability-traction control system cannot be disabled. REFER to: Anti-Lock Brake System (ABS) and Stability Control .

  8. AY7 CHECK FOR THE ADVANCETRAC ON FEATURE CONFIGURED ALWAYS ON

    • Check if the AdvanceTrac feature is configured always on. Refer to the Owner's Literature.

    Is the AdvanceTrac feature configured always on? 

    Yes  The traction control system cannot be disabled when the AdvanceTrac on feature is configured always on.
    No  DIAGNOSE the stability-traction control system cannot be disabled. REFER to: Anti-Lock Brake System (ABS) and Stability Control .

  9. AY8 CHECK FOR CORRECT IPC (INSTRUMENT PANEL CLUSTER) OPERATION

    • Ignition OFF.

    • Disconnect and inspect the IPC connector.

    • Repair:

      • corrosion (install new connector or terminals - clean module pins)
      • damaged or bent pins - install new terminals/pins
      • pushed-out pins - install new pins as necessary

    • Reconnect the IPC connector. Make sure it seats and latches correctly.

    • Operate the system and determine if the concern is still present.

    Is the concern still present? 

    Yes  CHECK OASIS for any applicable service articles: TSB, GSB, SSM or FSA. If a service article exists for this concern, DISCONTINUE this test and FOLLOW the service article instructions. If no service articles address this concern, INSTALL a new IPC. REFER to: Instrument Panel Cluster (IPC) .
    No  The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.
scientia non olet · About LEMON Manuals