Chart 1

WARNING: This page does not describe the selected car, but rather 31 other vehicles, including the 2018 Lincoln Navigator, 2018 Lincoln MKZ, 2018 Lincoln MKX, 2018 Lincoln MKT, and 2018 Lincoln MKC. However, it is still accessible from the selected car via links, so may be relevant.

Stalls/Quits: Idle, Acceleration, Cruise, Stall After Start
Runs Rough
Misses
Buck/Jerk
Hesitation/Stumble
Surge
Unique Idle Concerns: Rolling Idle

NOTE: For some vehicle applications, the engine may stall if left running while refueling. Advise the customer to turn the engine off while refueling to avoid contamination or damage to the evaporative emission (EVAP) system.

SYSTEM/COMPONENT	REFERENCE
Check the following parameter identifiers (PIDs): LONGFT1 or LONGFT2 (value between -20 and +20%) VPWR (value between 10.5 and 17.0 volts, and within 0.5 volt of battery voltage)	LONGFT1 or LONGFT2 value low (-): Continue diagnosis. Concentrate checks in areas that would cause the engine to run rich. LONGFT1 or LONGFT2 value high (+): Continue diagnosis. Concentrate checks in areas that would cause the engine to run lean. VPWR not between 10.5 and 17.0 volts: REFER to the appropriate Charging System article, Diagnosis And Testing to continue diagnosis. VPWR between 10.5 and 17.0 volts, but not within 0.5 volt of battery voltage: CHECK the B+ voltage to the powertrain control module (PCM) power relay. CHECK the VPWR circuit between the PCM and the PCM power relay. CHECK the PWR GND circuits.
Fuel Injection System	For vehicles that run rough at idle check the INJx_F PIDs (the x indicates the injector number) with the ignition ON, engine running. There is 1 INJx_F PID for each engine cylinder. All INJx_F PIDs must indicate NO FAULT. The INJx_F PIDs indicate a fault (an injector circuit concern is indicated). For Continental 2.0L, Continental 2.7L, Continental 3.0L, EcoSport 1.0L, EcoSport 2.0L, Edge 2.0L, Edge 2.7L, Escape/Kuga 1.5L, Escape/Kuga 2.0L, Expedition direct fuel injection system, Explorer 2.3L, Explorer 3.5L GTDI, F-150 2.7L direct fuel injection system, F-150 3.3L direct fuel injection system, F-150 3.5L direct fuel injection system, F-150 5.0L direct fuel injection system, Fiesta 1.0L, Fiesta 1.6L GTDI, Flex 3.5L GTDI, Focus, Ford GT direct fuel injection system, Fusion 1.5L, Fusion 2.0L, Fusion 2.7L, MKC, MKS 3.5L, MKT 2.0L, MKT 3.5L, MKX 2.0L, MKX 2.7L, MKZ 2.0L, MKZ 3.0L, Mustang 2.3L, Mustang 5.0L direct fuel injection system, Navigator direct fuel injection system, Taurus 2.0L, Taurus 3.5L GTDI and Transit 3.5L, GO to PINPOINT TEST DI . For all others, GO to PINPOINT TEST KG .
Mass Airflow (MAF) Sensor	GO to PINPOINT TEST DC .
Manifold Absolute Pressure (MAP) Sensor	GO to PINPOINT TEST DM .
Secondary Ignition System	For KA 1.5L TIVCT or Fiesta 1.6L TIVCT, GO to PINPOINT TEST JC . For all others, GO to PINPOINT TEST JB .
Fuel Delivery System	GO to PINPOINT TEST HC .
Exhaust System	GO to PINPOINT TEST HF .
Positive Crankcase Ventilation (PCV) System	GO to PINPOINT TEST HG .
Variable Camshaft Timing (VCT) System	GO to PINPOINT TEST HK .
EVAP System	GO to PINPOINT TEST HX .
Charging System	REFER to the appropriate Charging System article, Diagnosis And Testing to continue diagnosis.
Universal Heated Oxygen Sensor (HO2S)	GO to PINPOINT TEST DZ .
Automatic Transmission	REFER to the appropriate Automatic Transmission article, Diagnosis By Symptom to continue diagnosis.
Base Engine	REFER to the appropriate Engine System article, Diagnosis And Testing to continue diagnosis.
Intake Air System	GO to PINPOINT TEST HU .
Auto Start Stop System	GO to PINPOINT TEST AA .
Additional Testing	GO to PINPOINT TEST Z .
Additional Checks: Some vehicles have a TQ_CNTRL PID available. Check this PID to determine if the PCM is reducing torque. The TQ_CNTRL PID may indicate which component or system, if any, is requesting a torque reduction. Correct PCM vehicle identification (VID) block information. Refer to FLASH ELECTRICALLY ERASABLE PROGRAMMABLE READ ONLY MEMORY (EEPROM) to carry out the Making Changes to the VID Block procedure. Be aware of engine RPM and speed limiting functions of the PCM (look for incorrect high vehicle speed signal from ABS or VSS). Drivelines Manual transmission or clutch Charging system Traction control system (if equipped) A/C system Cruise control system (for surge with cruise control on)	REFER to the applicable Service Information article.
Brake Over Accelerator	CHECK for simultaneous brake pedal and accelerator pedal operation inadvertently activating the brake over accelerator feature. CHECK the BRKOVR_ACTION, BRKOVRD_POSS, and DIST_BRKOVRD PIDs for recent simultaneous brake pedal and accelerator pedal operation. ADVISE the customer that simultaneous brake pedal and accelerator pedal operation by the vehicle operator activates the brake over accelerator feature. REFER to POWERTRAIN CONTROL SOFTWARE for additional information.