LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2022 >> Mustang Mach 1, Automatic Trans >> Repair and Diagnosis >> Engine Mechanical >> Mechanical >> Engine - 5.0L 32V Ti-VCT (359KW/486PS) (WU)/5.0L Ti-VCT V8 (343KW/466PS) (MF) >> Removal And Installation >> Valve Cover LH >> Removal

Valve Cover LH: Removal

NOTE: During engine repair procedures, cleanliness is extremely important. Any foreign material, including any material created while cleaning gasket surfaces, that enters the oil passages, coolant passages or the oil pan, can cause engine failure.
NOTE: Unless otherwise noted, GT engine is depicted in graphics, Mach 1 engine is similar.

All vehicles 

  1. Release the fuel system pressure. Refer to: Fuel System Pressure Release .
  2. Disconnect the battery ground and positive cables. Refer to: Battery Disconnect and Connect .
  3. Remove the cowl grille panel. Refer to: Cowl Panel Grille .
    1. Detach the wiring harness retainer.
    2. If equipped, remove and discard the nuts and remove the strut tower cross brace.
    GFD716754Courtesy of FORD MOTOR COMPANY
  5. If equipped, remove the fasteners and the cowl extension.
    GFD716755Courtesy of FORD MOTOR COMPANY

    GT 

  6. Remove the engine appearance cover caps.
    GFD716756Courtesy of FORD MOTOR COMPANY
  7. NOTE: The engine appearance cover rubber grommets may remain on the cover. If so, remove the grommets from the cover and install them on the intake manifold before installing the cover.

    Remove the nuts and the engine appearance cover.

    GFD716757Courtesy of FORD MOTOR COMPANY
  8. Remove the following items:

    1. Air cleaner outlet pipe. Refer to: Air Cleaner Outlet Pipe .
    2. Air cleaner. Refer to: Air Cleaner .
    3. Intake air resonator outlet pipe. Refer to: Intake Air Resonator Outlet Pipe .

  9. Disconnect the quick release coupling and remove the crankcase vent tube. Refer to: Quick Release Coupling .
    GFD716869Courtesy of FORD MOTOR COMPANY
  10. Disconnect the quick release coupling and detach the retainer. Refer to: Quick Release Coupling .
    GFD716870Courtesy of FORD MOTOR COMPANY

    Mach 1 

    1. Remove the nuts and the heater hose support.
    2. Disconnect the quick release coupling and remove the crankcase vent tube. Refer to: Quick Release Coupling .
    3. Disconnect the quick release coupling and detach the retainer. Refer to: Quick Release Coupling .
    GFD716871Courtesy of FORD MOTOR COMPANY

    All vehicles 

  12. Disconnect the fuel supply tube quick release coupling and position the fuel supply tube aside. Refer to: Quick Release Coupling .
    GFD716872Courtesy of FORD MOTOR COMPANY
  13. Remove the LH ignition coils. Refer to: Ignition Coil-On-Plug .
    1. Disconnect the engine wiring harness electrical connectors.
    2. Detach the wiring harness retainers and position the harness aside.
    GFD716873Courtesy of FORD MOTOR COMPANY
    1. Remove the oil level indicator.
    2. Depress the tab.
    3. Rotate the oil level indicator tube counterclockwise.
    4. Pull the oil level indicator tube from the engine.
    GFD716874Courtesy of FORD MOTOR COMPANY
  16. Loosen the bolts, the stud bolts and remove the valve cover.
    GFD716875Courtesy of FORD MOTOR COMPANY
  17. NOTE: Clean the valve cover gasket groove with soap and water or a suitable solvent.

    Remove and discard the gasket.

    GFD716876Courtesy of FORD MOTOR COMPANY
  18. Inspect the VCT variable force solenoid seals. Remove any damaged seals using the special tools. Use Special Service Tool: 205-153 (T80T-4000-W) Handle., 205-142 (T80T-4000-J) Installer, Differential Bearing Cone.
    GFD716877Courtesy of FORD MOTOR COMPANY
  19. Inspect the spark plug seals. Remove any damaged seals using the special tools. Use Special Service Tool: 205-153 (T80T-4000-W) Handle., 303-1247 VCT Spark Plug Tube Seal Remover and Installer.
    GFD716878Courtesy of FORD MOTOR COMPANY
  20. Clean and prepare the RTV sealing surface. Refer to: RTV Sealing Surface Cleaning and Preparation .
GFD716879Courtesy of FORD MOTOR COMPANY
scientia non olet · About LEMON Manuals