LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2022 >> Mustang Mach 1, Automatic Trans >> Repair and Diagnosis >> Electrical >> Gauges >> Instrumentation, Message Center And Warning Chimes (Diagnosis And Testing, General Procedures, Removal And Installation) >> Diagnosis And Testing >> Instrumentation, Message Center and Warning Chimes >> Pinpoint Tests >> Pinpoint Test Cm: U0232:00 Or U0233:00

Pinpoint Test Cm: U0232:00 Or U0233:00

  1. Normal Operation and Fault Conditions 

    REFER to: Communications Network - System Operation and Component Description .

    DTC Fault Trigger Conditions 

    DTC Description Fault Trigger Condition
    IPC U0232:00 Lost Communication With Side Obstacle Detection Control Module 'A': No Sub Type Information Sets in continuous memory in the IPC if data messages received from the SODL through the GWM are missing for 5 seconds or longer.
    IPC U0233:00 Lost Communication With Side Obstacle Detection Control Module 'B': No Sub Type Information Sets in continuous memory in the IPC if data messages received from the SODR through the GWM are missing for 5 seconds or longer.

    Possible Sources 

    • Communication concern
    • GWM concern
    • SODL
    • SODR
    • IPC

  2. CM1 VERIFY THE CUSTOMER CONCERN

    • Ignition ON.

    • Verify there is an observable symptom present.

    Is an observable symptom present? 

    Yes  GO to  CM2
    No  Clear the DTC. The system is operating normally at this time. The DTC may have been set due to high network traffic or an intermittent fault condition.

  3. CM2 CHECK THE COMMUNICATION NETWORK

    • Using a diagnostic scan tool, perform the network test.

    Does the SODL or SODR pass the network test? 

    Yes  GO to  CM3
    No  REFER to: Communications Network .

  4. CM3 PERFORM THE IPC (INSTRUMENT PANEL CLUSTER) SELF-TEST

    • Using a diagnostic scan tool, perform the IPC self-test.

    Are any non-network Diagnostic Trouble Codes (DTCs) present? 

    Yes  REFER to Diagnostic Trouble Code (DTC) Chart 
    No  GO to  CM4

  5. CM4 CHECK THE GWM (GATEWAY MODULE A) DIAGNOSTIC TROUBLE CODES (DTCS)

    • Using a diagnostic scan tool, check the GWM Continuous Memory Diagnostic Trouble Codes (CMDTCs).

    Are any Diagnostic Trouble Codes (DTCs) recorded? 

    Yes  REFER to: Communications Network .
    No  GO to  CM5

  6. CM5 PERFORM THE SODL (SIDE OBSTACLE DETECTION CONTROL MODULE LH) OR SODR (SIDE OBSTACLE DETECTION CONTROL MODULE RH) SELF-TEST

    • Using a diagnostic scan tool, perform the SODL or SODR self-test.

    Are any non-network Diagnostic Trouble Codes (DTCs) present? 

    Yes  REFER to: Blind Spot Information System .
    No  GO to  CM6

  7. CM6 RECHECK THE IPC (INSTRUMENT PANEL CLUSTER) DIAGNOSTIC TROUBLE CODES (DTCS)

    • Using a diagnostic scan tool, clear the IPC Diagnostic Trouble Codes (DTCs).

    • Ignition OFF.

    • Ignition ON.

    • Wait 10 seconds.

    • Using a diagnostic scan tool, perform the continuous memory self-test.

    • Check the IPC Diagnostic Trouble Codes (DTCs).

    Is DTC U0232:00 or DTC U0233:00 still present? 

    Yes  GO to  CM7
    No  The system is operating correctly at this time. The DTC may have been set due to high network traffic or an intermittent fault condition.

  8. CM7 CHECK FOR OTHER CAUSES OF COMMUNICATION NETWORK CONCERN

    NOTE: If new modules were installed prior to the DTC being set, the module configuration may be incorrectly set during the PMI, or the PMI may not have been carried out.

    • CHECK the vehicle service history for recent service actions related to the SODL, SODR, GWM or IPC. If recent service history is found:

      • verify correct replacement module was installed

        • HVBOM may be used to verify correct part fitment

      • verify the configuration of replacement module was correct

        • re-configure module using as-built data if prior configuration is suspect

      • verify the module was not obtained from a like vehicle and installed into customer vehicle

        • return the swapped module to source vehicle and obtain new replacement module

    • Operate the system and determine if the observable symptom is still present.

    Is the observable symptom still present? 

    Yes  GO to  CM8
    No  The system is operating correctly at this time. The concern may have been due to incorrect parts replacement procedures or incorrect module configuration.

  9. CM8 CHECK FOR CORRECT SODL (SIDE OBSTACLE DETECTION CONTROL MODULE LH) OR SODR (SIDE OBSTACLE DETECTION CONTROL MODULE RH) OPERATION

    • Ignition OFF.

    • Disconnect and inspect the SODL or SODR connectors.

    • Repair:

      • corrosion (install new connector or terminals - clean module pins)
      • damaged or bent pins - install new terminals/pins
      • pushed-out pins - install new pins as necessary

    • Reconnect all SODL or SODR connectors. Make sure they seat and latch correctly.

    • Operate the system and determine if the concern is still present.

    Is the concern still present? 

    Yes  CHECK OASIS for any applicable service articles: TSB, GSB, SSM or FSA. If a service article exists for this concern, DISCONTINUE this test and FOLLOW the service article instructions. If no service articles address this concern, INSTALL a new SODL or SODR. REFER to: Side Obstacle Detection Control Module (SODCM) .
    No  The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.
scientia non olet · About LEMON Manuals