LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2022 >> Mustang Mach 1, Automatic Trans >> Repair and Diagnosis >> Electrical >> Gauges >> Instrumentation, Message Center And Warning Chimes (Diagnosis And Testing, General Procedures, Removal And Installation) >> Diagnosis And Testing >> Instrumentation, Message Center and Warning Chimes >> Pinpoint Tests >> Pinpoint Test Cc: U0122:00

Pinpoint Test Cc: U0122:00

  1. Normal Operation and Fault Conditions 

    REFER to: Communications Network - System Operation and Component Description .

    DTC Fault Trigger Conditions 

    DTC Description Fault Trigger Condition
    IPC U0122:00 Lost Communication With Vehicle Dynamics Control Module: No Sub Type Information Sets in continuous memory in the IPC if data messages received from the VDM through the GWM are missing for 5 seconds or longer.

    Possible Sources 

    • Communication concern
    • GWM concern
    • VDM
    • IPC

  2. CC1 VERIFY THE CUSTOMER CONCERN

    • Ignition ON.

    • Verify there is an observable symptom present.

    Is an observable symptom present? 

    Yes  GO to  CC2
    No  CLEAR the DTC. The system is operating normally at this time. The DTC may have been set due to high network traffic or an intermittent fault condition.

  3. CC2 CHECK THE COMMUNICATION NETWORK

    • Using a diagnostic scan tool, perform the network test.

    Does the VDM pass the network test? 

    Yes  GO to  CC3
    No  REFER to: Communications Network .

  4. CC3 PERFORM THE IPC (INSTRUMENT PANEL CLUSTER) SELF-TEST

    • Using a diagnostic scan tool, perform the IPC self-test.

    Are any non-network Diagnostic Trouble Codes (DTCs) present? 

    Yes  REFER to Diagnostic Trouble Code (DTC) Chart 
    No  GO to  CC4

  5. CC4 CHECK THE GWM (GATEWAY MODULE A) DIAGNOSTIC TROUBLE CODES (DTCS)

    • Using a diagnostic scan tool, check the GWM Continuous Memory Diagnostic Trouble Codes (CMDTCs).

    Are any Diagnostic Trouble Codes (DTCs) recorded? 

    Yes  REFER to: Communications Network .
    No  GO to  CC5

  6. CC5 PERFORM THE VDM (VEHICLE DYNAMICS CONTROL MODULE) SELF-TEST

    • Using a diagnostic scan tool, perform the VDM self-test.

    Are any non-network Diagnostic Trouble Codes (DTCs) present? 

    Yes  REFER to: Vehicle Dynamic Suspension .
    No  GO to  CC6

  7. CC6 RECHECK THE IPC (INSTRUMENT PANEL CLUSTER) DIAGNOSTIC TROUBLE CODES (DTCS)

    • Using a diagnostic scan tool, clear the IPC Diagnostic Trouble Codes (DTCs).

    • Ignition OFF.

    • Ignition ON.

    • Wait 10 seconds.

    • Using a diagnostic scan tool, perform the continuous memory self-test.

    • Check the IPC Diagnostic Trouble Codes (DTCs).

    Is DTC U0122:00 still present? 

    Yes  GO to  CC7
    No  The system is operating correctly at this time. The DTC may have been set due to high network traffic or an intermittent fault condition.

  8. CC7 CHECK FOR OTHER CAUSES OF COMMUNICATION NETWORK CONCERN

    NOTE: If new modules were installed prior to the DTC being set, the module configuration can be incorrectly set during the PMI or the PMI may not have been carried out.

    • CHECK the vehicle service history for recent service actions related to the VDM, GWM or IPC. If recent service history is found:

      • verify correct replacement module was installed

        • HVBOM may be used to verify correct part fitment

      • verify the configuration of replacement module was correct

        • re-configure module using as-built data if prior configuration is suspect

      • verify the module was not obtained from a like vehicle and installed into customer vehicle

        • return the swapped module to source vehicle and obtain new replacement module

    • Operate the system and determine if the observable symptom is still present.

    Is the observable symptom still present? 

    Yes  GO to  CC8
    No  The system is operating correctly at this time. The concern may have been due to incorrect parts replacement procedures or incorrect module configuration.

  9. CC8 CHECK FOR CORRECT VDM (VEHICLE DYNAMICS CONTROL MODULE) OPERATION

    • Ignition OFF.

    • Disconnect and inspect the VDM connectors.

    • Repair:

      • corrosion (install new connector or terminals - clean module pins)
      • damaged or bent pins - install new terminals/pins
      • pushed-out pins - install new pins as necessary

    • Reconnect all VDM connectors. Make sure they seat and latch correctly.

    • Operate the system and determine if the concern is still present.

    Is the concern still present? 

    Yes  CHECK OASIS for any applicable service articles: TSB, GSB, SSM or FSA. If a service article exists for this concern, DISCONTINUE this test and FOLLOW the service article instructions. If no service articles address this concern, INSTALL a new VDM. REFER to: Vehicle Dynamics Control Module (VDM) .
    No  The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.
scientia non olet · About LEMON Manuals