LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2022 >> Mustang Mach 1 Premium, Automatic Trans >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 16 (Engine - 5.2L 32V Ti-VCT - Supercharged) >> Removal And Installation >> Engine Mount LH >> Removal

Engine Mount LH: Removal

WARNING: This page is about a different variant/trim than selected.
  1. With the vehicle in NEUTRAL, position it on a hoist. Refer to: Jacking and Lifting - GT500 - Overview .
  2. Disconnect the battery ground and positive cables. Refer to: Battery Disconnect and Connect .
  3. NOTE: Make sure to minimize damage to sealer foam and avoid pulling apart dash seal brackets from retainer pins. Excessive damage may allow engine noise, fumes, air or water to enter the passenger compartment.

    1. Remove the steering column dash seal nuts.
    2. Loosen the dash seal.
    3. Hand start the dash seal nuts.

    GFD715894Courtesy of FORD MOTOR COMPANY
  4. Using a holding device, hold the steering wheel in the straight-ahead position.
    GFD715211Courtesy of FORD MOTOR COMPANY
  5. Remove the following items:

    1. NOTE: No disassembly of the hood is required after the hood is removed.

      Hood. Refer to: Hood .

    2. Strut tower cross brace. Refer to: Strut Tower Cross Brace - GT500 .
    3. Air cleaner outlet pipe.
    4. Air cleaner. Refer to: Air Cleaner .
    5. Battery tray. Refer to: Battery Tray .

  6. Remove the fasteners and the battery heat shield.
    GFD717218Courtesy of FORD MOTOR COMPANY
    • Slide the insulator up and disconnect the exhaust CMP sensor electrical connector.

    • Detach the wiring harness retainer.

    • Remove the bolt and the CMP sensor.

    GFD717219Courtesy of FORD MOTOR COMPANY
  8. Remove the LH engine mount nut.
    GFD717168Courtesy of FORD MOTOR COMPANY
  9. Remove the RH engine mount nut.
    GFD717220Courtesy of FORD MOTOR COMPANY
  10. NOTE: Do not position the legs of the Engine Support Bar on the fenders. Instead, the legs should be positioned on the body structure. Failure to follow these instructions may result in body damage.

    Install the special tools and raise the engine 12 mm (0.5 inch). Install Special Service Tool: 303-F070 Support Bar, Engine.Use Special Service Tool: 303-050 (T70P-6000) Lifting Bracket, Engine.

    GFD717221Courtesy of FORD MOTOR COMPANY
  11. Remove the engine front undershield. Refer to: Engine Front Undershield - GT500 .
  12. WARNING: Do not reuse steering column shaft bolts. This may result in fastener failure and steering column shaft detachment or loss of steering control. Failure to follow this instruction may result in serious injury to vehicle occupant(s).
    WARNING: DO NOT hammer, pry or force steering column and column shafts during installation or removal. Failure to follow this instruction may cause damage to steering components that could lead to loss of steering control during vehicle operation and could result in serious personal injury or death.
    WARNING: DO NOT attempt to remove or install the steering column lower u-joint at the steering gear without first loosening the steering column dash seal and fasteners. Failure to follow this instruction may cause damage to steering components that could lead to loss of steering control during vehicle operation and could result in serious personal injury or death.

    Detach the steering column lower shaft from the lower coupling.

    1. Remove and discard the steering column shaft bolt.
    2. Pull apart the steering column shaft from the coupling.
    3. Secure the lower shaft to the frame rail to avoid damage to the shaft.

    GFD715900Courtesy of FORD MOTOR COMPANY
  13. Remove the fasteners and the LH motor mount bracket.
    GFD717172Courtesy of FORD MOTOR COMPANY
  14. Remove the bolts and the engine mount.
GFD716725Courtesy of FORD MOTOR COMPANY
scientia non olet · About LEMON Manuals