Diagnostic Trouble Code (DTC) Chart
WARNING: This page is about a different variant/trim than selected.
Diagnostics in this article assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .
| Module | DTC | Description | Action |
|---|---|---|---|
| PCM | P0030:00 | HO2S Heater Control Circuit (Bank 1, Sensor 1): No Sub Type Information | GO to Pinpoint Test DZ |
| PCM | P0036:00 | HO2S Heater Control Circuit (Bank 1, Sensor 2): No Sub Type Information | GO to Pinpoint Test DW |
| PCM | P0037:00 | HO2S Heater Control Circuit Low (Bank 1, Sensor 2): No Sub Type Information | GO to Pinpoint Test DW |
| PCM | P0038:00 | HO2S Heater Control Circuit High (Bank 1, Sensor 2): No Sub Type Information | GO to Pinpoint Test DW |
| PCM | P0053:00 | HO2S Heater Resistance (Bank 1, Sensor 1): No Sub Type Information | GO to Pinpoint Test DZ |
| PCM | P0054:00 | HO2S Heater Resistance (Bank 1, Sensor 2): No Sub Type Information | GO to Pinpoint Test DW |
| PCM | P00D2:00 | HO2S Heater Control Circuit Range/Performance (Bank 1 Sensor 2): No Sub Type Information | GO to Pinpoint Test DW |
| PCM | P0130:00 | O2 Sensor Circuit (Bank 1 Sensor 1): No Sub Type Information | GO to Pinpoint Test DZ |
| PCM | P0131:00 | O2 Sensor Circuit Low Voltage (Bank 1 Sensor 1): No Sub Type Information | GO to Pinpoint Test DZ |
| PCM | P0132:00 | O2 Sensor Circuit High Voltage (Bank 1 Sensor 1): No Sub Type Information | GO to Pinpoint Test DZ |
| PCM | P0133:00 | O2 Sensor Circuit Slow Response (Bank 1 Sensor 1): No Sub Type Information | GO to Pinpoint Test DZ |
| PCM | P0134:00 | O2 Sensor Circuit No Activity Detected (Bank 1 Sensor 1): No Sub Type Information | GO to Pinpoint Test DZ |
| PCM | P0135:00 | O2 Sensor Heater Circuit (Bank 1 Sensor 1): No Sub Type Information | GO to Pinpoint Test DZ |
| PCM | P0136:00 | O2 Sensor Circuit (Bank 1 Sensor 2): No Sub Type Information | GO to Pinpoint Test DW |
| PCM | P0137:00 | O2 Sensor Circuit Low Voltage (Bank 1 Sensor 2): No Sub Type Information | GO to Pinpoint Test DW |
| PCM | P0138:00 | O2 Sensor Circuit High Voltage (Bank 1 Sensor 2): No Sub Type Information | GO to Pinpoint Test DW |
| PCM | P0139:00 | O2 Sensor Circuit Slow Response (Bank 1 Sensor 2): No Sub Type Information | GO to Pinpoint Test DW |
| PCM | P013A:00 | O2 Sensor Slow Response - Rich to Lean (Bank 1 and Sensor 2): No Sub Type Information | GO to Pinpoint Test DW |
| PCM | P013B:00 | O2 Sensor Slow Response - Lean to Rich (Bank 1, Sensor 2): No Sub Type Information | GO to Pinpoint Test DW |
| PCM | P013E:00 | O2 Sensor Delayed Response - Rich to Lean (Bank 1 Sensor 2): No Sub Type Information | GO to Pinpoint Test DW |
| PCM | P0140:00 | O2 Sensor Circuit No Activity Detected (Bank 1 Sensor 2): No Sub Type Information | GO to Pinpoint Test DW |
| PCM | P0141:00 | O2 Sensor Heater Circuit (Bank 1 Sensor 2): No Sub Type Information | GO to Pinpoint Test DW |
| PCM | P0171:00 | System Too Lean Bank 1: No Sub Type Information | GO to Pinpoint Test H |
| PCM | P0172:00 | System Too Rich Bank 1: No Sub Type Information | GO to Pinpoint Test H |
| PCM | P064D:00 | Internal Control Module O2 Sensor Processor Performance - Bank 1: No Sub Type Information | GO to Pinpoint Test DZ |
| PCM | P1127:00 | Exhaust Temperature Out of Range, O2 Sensor Tests Not Completed: No Sub Type Information | GO to Pinpoint Test DZ |
| PCM | P1137:00 | Lack Of HO2S12 Switches - Sensor Indicates Lean: No Sub Type Information | GO to Pinpoint Test H |
| PCM | P1138:00 | Lack Of HO2S12 Switches - Sensor Indicates Rich: No Sub Type Information | GO to Pinpoint Test H |
| PCM | P1646:00 | Linear O2 Sensor Control Chip (Bank 1): No Sub Type Information | GO to Pinpoint Test DZ |
| PCM | P164A:00 | O2 Sensor Positive Current Trim Circuit Performance (Bank 1 Sensor 1): No Sub Type Information | GO to Pinpoint Test DZ |
| PCM | P2096:00 | Post Catalyst Fuel Trim System Too Lean Bank 1: No Sub Type Information | GO to Pinpoint Test DZ |
| PCM | P2097:00 | Post Catalyst Fuel Trim System Too Rich Bank 1: No Sub Type Information | GO to Pinpoint Test DZ |
| PCM | P2195:00 | O2 Sensor Signal Biased/Stuck Lean - Bank 1, Sensor 1: No Sub Type Information | GO to Pinpoint Test H |
| PCM | P2196:00 | O2 Sensor Signal Biased/Stuck Rich - Bank 1, Sensor 1: No Sub Type Information | GO to Pinpoint Test H |
| PCM | P219A:00 | Bank 1 Air-Fuel Ratio Imbalance: No Sub Type Information | GO to Pinpoint Test H |
| PCM | P219C:00 | Cylinder 1 Air-Fuel Ratio Imbalance: No Sub Type Information | GO to Pinpoint Test H |
| PCM | P219D:00 | Cylinder 2 Air-Fuel Ratio Imbalance: No Sub Type Information | GO to Pinpoint Test H |
| PCM | P219E:00 | Cylinder 3 Air-Fuel Ratio Imbalance: No Sub Type Information | GO to Pinpoint Test H |
| PCM | P219F:00 | Cylinder 4 Air-Fuel Ratio Imbalance: No Sub Type Information | GO to Pinpoint Test H |
| PCM | P2237:00 | O2 Sensor Positive Current Control Circuit/Open - Bank 1, Sensor 1: No Sub Type Information | GO to Pinpoint Test DZ |
| PCM | P2243:00 | O2 Sensor Reference Voltage Circuit/Open - Bank 1, Sensor 1: No Sub Type Information | GO to Pinpoint Test DZ |
| PCM | P2251:00 | O2 Sensor Negative Current Control Circuit/Open - Bank 1, Sensor 1: No Sub Type Information | GO to Pinpoint Test DZ |
| PCM | P2270:00 | O2 Sensor Signal Stuck Lean - Bank 1, Sensor 2: No Sub Type Information | GO to Pinpoint Test DW |
| PCM | P2270:00 | O2 Sensor Signal Stuck Lean - Bank 1, Sensor 2: No Sub Type Information | GO to Pinpoint Test H |
| PCM | P2271:00 | O2 Sensor Signal Stuck Rich - Bank 1, Sensor 2: No Sub Type Information | GO to Pinpoint Test DW |
| PCM | P2271:00 | O2 Sensor Signal Stuck Rich - Bank 1, Sensor 2: No Sub Type Information | GO to Pinpoint Test H |
| PCM | P2297:00 | O2 Sensor Out of Range During Deceleration Bank 1, Sensor 1: No Sub Type Information | GO to Pinpoint Test DW |
| PCM | P2626:00 | O2 Sensor Positive Current Trim Circuit/Open Bank 1 Sensor 1: No Sub Type Information | GO to Pinpoint Test DZ |
| PCM | P2627:00 | O2 Sensor Positive Current Trim Circuit Low Bank 1, Sensor 1: No Sub Type Information | GO to Pinpoint Test DZ |
| PCM | P2628:00 | O2 Sensor Positive Current Trim Circuit High Bank 1, Sensor 1: No Sub Type Information | GO to Pinpoint Test DZ |
| PCM | P2A01:00 | O2 Circuit Range/Performance (Bank 1, Sensor 2): No Sub Type Information | GO to Pinpoint Test DW |
| PCM | P2BEC:00 | Fuel Control System 'A' Too Lean Bank 1: No Sub Type Information | GO to Pinpoint Test H |
| PCM | P2BED:00 | Fuel Control System 'A' Too Rich Bank 1: No Sub Type Information | GO to Pinpoint Test H |