LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2022 >> E-Transit Van Cargo Extended >> Repair and Diagnosis >> Accessories & Equipment >> Drivers Assistance Systems - ADAS >> Parking Aid - Vehicles With: Active Park Assist >> Diagnosis And Testing >> Parking Aid >> Pinpoint Tests >> Pinpoint Test G: B13F3:96, B13F4:96

Pinpoint Test G: B13F3:96, B13F4:96

  1. NOTE: Before disconnecting any of the active park assist sensors, verify the connectors are properly seated and latched.

    Normal Operation and Fault Conditions 

    REFER to: Parking Aid - System Operation and Component Description .

    DTC Fault Trigger Conditions 

    DTC Description Fault Trigger Condition
    IPMB B13F3:96 Left Rear Side Sensor: Component Internal Failure A continuous and on-demand DTC that sets in the IPMB when the left rear active park assist sensor has internally failed or has an incorrect attenuation time.
    IPMB B13F4:96 Right Rear Side Sensor: Component Internal Failure A continuous and on-demand DTC that sets in the IPMB when the right rear active park assist sensor has internally failed or has an incorrect attenuation time.

    Possible Sources 

    • Rear active park assist sensor
    • IPMB

  2. G1 CHECK THE CONTINUOUS AND ON-DEMAND IPMB (IMAGE PROCESSING MODULE B) DIAGNOSTIC TROUBLE CODES (DTCS)

    • Ignition ON.

    • Using a diagnostic scan tool, retrieve the IPMB Diagnostic Trouble Codes (DTCs).

    Are Diagnostic Trouble Codes (DTCs) other than DTC B13F3:96 or DTC B13F4:96 present? 

    Yes  DIAGNOSE all other IPMB Diagnostic Trouble Codes (DTCs) first. REFER to Diagnostic Trouble Code (DTC) Chart .
    No  GO to  G2

  3. G2 CHECK THE REAR ACTIVE PARK ASSIST SENSOR OPERATION

    • Clean the rear bumper and sensors with high-pressure water.

    • Make sure the suspect rear active park assist sensor(s) is flush-mounted in the bezel.

    Does the system pass the azimuth system check? 

    Yes  The system is operating correctly at this time, the concern may have been caused by a dirty, blocked or incorrectly mounted rear active park assist sensor.
    No  GO to  G3

  4. G3 INSTALL A KNOWN GOOD SENSOR

    • Ignition OFF.

    • Ignition ON.

    • Using a diagnostic scan tool, clear the IPMB Diagnostic Trouble Codes (DTCs) and repeat the self-test.

    Is DTC B13F3:96 or DTC B13F4:96 still present? 

    Yes  GO to  G4
    No  INSTALL a new rear active park assist sensor for the suspect sensor. REFER to: Rear Active Park Assist Sensors .

  5. G4 CHECK FOR CORRECT IPMB (IMAGE PROCESSING MODULE B) OPERATION

    • Ignition OFF.

    • Disconnect and inspect all IPMB connectors.

    • Repair:

      • corrosion (install new connector or terminals - clean module pins)
      • damaged or bent pins - install new terminals/pins
      • pushed-out pins - install new pins as necessary

    • Reconnect the IPMB connectors. Make sure they seat and latch correctly.

    • Operate the system and determine if the concern is still present.

    Is the concern still present? 

    Yes  CHECK OASIS for any applicable service articles: TSB, GSB, SSM or FSA. If a service article exists for this concern, DISCONTINUE this test and FOLLOW the service article instructions. If no service articles address this concern, INSTALL a new IPMB. REFER to: IMAGE PROCESSING MODULE B (IPMB) - VEHICLES WITH: PARKING AID CAMERA .
    No  The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector. ADDRESS the root cause of any connector or pin issues.
scientia non olet · About LEMON Manuals