DTC Chart
Diagnostics in this article assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods
| Module | DTC | Description | Action |
|---|---|---|---|
| APIM | C1001:01 | Vision System Camera: General Electrical Failure | GO to Pinpoint Test A |
| APIM | C1001:01 | Vision System Camera: General Electrical Failure | GO to Pinpoint Test H |
| APIM | C1001:02 | Vision System Camera: General Signal Failure | GO to Pinpoint Test H |
| APIM | C1001:1C | Vision System Camera: Circuit Voltage Out Of Range | GO to Pinpoint Test H |
| APIM | C1001:81 | Vision System Camera: Invalid Serial Data Received | GO to Pinpoint Test H |
| APIM | C1001:87 | Vision System Camera: Missing Message | GO to Pinpoint Test H |
| BCM | B115E:01 | Rear Camera: General Electrical Failure | GO to Pinpoint Test A |
| BCM | B115E:02 | Rear Camera: General Signal Failure | GO to Pinpoint Test A |
| BCM | B115E:08 | Camera Module: Bus Signal / Message Failure | GO to Pinpoint Test A |
| BCM | B115E:49 | Camera: Internal Electrical Failure | GO to Pinpoint Test A |
| BCM | B115E:9A | Camera Module: Component or System Operating Conditions | GO to Pinpoint Test A |
| IPMB | B115E:31 | Camera Module: No Signal | GO to Pinpoint Test J |
| IPMB | B115E:49 | Camera Module: Internal Electronic Failure | GO to Pinpoint Test R |
| IPMB | B12BE:31 | Left Front Camera: No Signal | GO to Pinpoint Test L |
| IPMB | B12BE:49 | Left Front Camera: Internal Electronic Failure | GO to Pinpoint Test S |
| IPMB | B12BF:31 | Right Front Camera: No Signal | GO to Pinpoint Test M |
| IPMB | B12BF:49 | Right Front Camera: Internal Electronic Failure | GO to Pinpoint Test T |
| IPMB | B148E:31 | Front Camera: No Signal | GO to Pinpoint Test K |
| IPMB | B148E:49 | Front Camera: Internal Electronic Failure | GO to Pinpoint Test U |
| IPMB | B14A4:11 | Camera Power: Circuit Short To Ground | GO to Pinpoint Test Y |
| IPMB | B14A5:11 | Multi-Camera View Switch: Circuit Short To Ground | GO to Pinpoint Test N |
| IPMB | C1001:78 | Vision System Camera: Alignment Or Adjustment Incorrect | GO to Pinpoint Test V |
| IPMB | U0121:87 | Lost Communication With Anti-Lock Brake System (ABS) Control Module "A": Missing Message | GO to Pinpoint Test Z |
| IPMB | U0131:87 | Lost Communication With Power Steering Control Module "A": Missing Message | GO to Pinpoint Test Z |
| IPMB | U0159:87 | Lost Communication With Parking Assist Control Module "A": Missing Message | GO to Pinpoint Test Z |
| IPMB | U0253:87 | Lost Communication With Accessory Protocol Interface Module: Missing Message | GO to Pinpoint Test Z |
| IPMB | U0415:00 | Invalid Data Received from Anti-Lock Brake System (ABS) Control Module "A": No Sub Type Information | GO to Pinpoint Test AA |
| IPMB | U0420:00 | Invalid Data Received from Power Steering Control Module "A": No Sub Type Information | GO to Pinpoint Test AA |
| IPMB | U045A:00 | Invalid Data Received From Parking Assist Control Module "A": No Sub Type Information | GO to Pinpoint Test AA |
| IPMB | U0554:00 | Invalid Data Received From Accessory Protocol Interface Module: No Sub Type Information | GO to Pinpoint Test AA |
| IPMB | U1000:11 | Solid State Driver Protection Active -Driver Disabled: Circuit Short To Ground | GO to Pinpoint Test AB |
| IPMB | U201A:55 | Control Module Main Calibration Data: Not Configured | GO to Pinpoint Test AC |
| IPMB | U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test AC |
| IPMB | U3000:42 | Control Module: General Memory Failure | GO to Pinpoint Test AD |
| IPMB | U3000:49 | Control Module: Internal Electronic Failure | GO to Pinpoint Test AD |