LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2021 >> Transit-250 Base, Van Cargo, 3.5L Eng VIN 8, AWD >> Repair and Diagnosis >> Accessories & Equipment >> Drivers Assistance Systems - ADAS >> Parking Aid - Vehicles With: Rear Parking Aid >> Diagnosis And Testing >> Parking Aid >> Pinpoint Test(s) >> Pinpoint Test T: U0101:00 Or U0402:00

Pinpoint Test T: U0101:00 Or U0402:00

  1. Normal Operation and Fault Conditions 

    DTC Fault Trigger Conditions 

    DTC Description Fault Trigger Condition
    PAM U0101:00 Lost Communication with TCM: No Sub Type Information Sets in continuous memory in the PAM if data messages received from the TCM through the GWM are missing for 5 seconds or longer.
    PAM U0402:00 Invalid Data Received from TCM: No Sub Type Information Sets in the PAM when the PAM received invalid network data from the TCM through the GWM for 5 seconds or longer.

    Possible Sources 

    • Communication concern
    • PAM
    • GWM
    • TCM

  2. T1 VERIFY THE CUSTOMER CONCERN

    • Ignition ON.

    • Verify there is an observable symptom present.

    Is an observable symptom present? 

    Yes  GO to  T2
    No  Clear the DTC. The system is operating normally at this time. The DTC may have been set due to high network traffic, or an intermittent fault condition.

  3. T2 VERIFY THE DIAGNOSTIC SCAN TOOL COMMUNICATES WITH THE TCM (TRANSMISSION CONTROL MODULE)

    • Connect the diagnostic scan tool.

    • Check that a vehicle session can be established using the diagnostic scan tool.

    Can a vehicle session be established? 

    Yes  GO to  T3
    No  REFER to: Communications Network .

  4. T3 CHECK THE PAM (PARKING ASSIST CONTROL MODULE) CONTINUOUS MEMORY DIAGNOSTIC TROUBLE CODES (CMDTCS)

    • Ignition ON.

    • Using a diagnostic scan tool, perform the PAM self-test.

    • Clear the Diagnostic Trouble Codes (DTCs).

    • Wait 10 seconds.

    • Repeat the PAM self-test.

    Are any non-network Diagnostic Trouble Codes (DTCs) present? 

    Yes  DIAGNOSE all non-network Diagnostic Trouble Codes (DTCs). REFER to Diagnostic Trouble Code (DTC) Chart .
    No  GO to  T4

  5. T4 CHECK THE GWM (GATEWAY MODULE A) DIAGNOSTIC TROUBLE CODES (DTCS)

    • Using a diagnostic scan tool, check the GWM Continuous Memory Diagnostic Trouble Codes (CMDTCs).

    Are any Diagnostic Trouble Codes (DTCs) recorded? 

    Yes  REFER to: Communications Network .
    No  GO to  T5

  6. T5 PERFORM THE TCM (TRANSMISSION CONTROL MODULE) SELF-TEST

    • Using a diagnostic scan tool, perform the TCM self-test.

    Are any non-network Diagnostic Trouble Codes (DTCs) present? 

    Yes  DIAGNOSE all non-network Diagnostic Trouble Codes (DTCs). REFER to: Electronic Engine Controls - 3.5L EcoBoost . REFER to: Electronic Engine Controls - 3.5L Duratec .
    No  GO to  T6

  7. T6 RECHECK THE PAM (PARKING ASSIST CONTROL MODULE) DIAGNOSTIC TROUBLE CODES (DTCS)

    • Using a diagnostic scan tool, clear the PAM Diagnostic Trouble Codes (DTCs).

    • Ignition OFF.

    • Ignition ON.

    • Wait 10 seconds.

    • Using a diagnostic scan tool, perform the continuous memory self-test.

    • Check the PAM Diagnostic Trouble Codes (DTCs).

    Is DTC U0101:00 or U0402:00 present? 

    Yes  GO to  T7
    No  The system is operating correctly at this time. The DTC may have set due to high network traffic, or an intermittent fault condition.

  8. T7 CHECK FOR OTHER CAUSES OF COMMUNICATION NETWORK CONCERN

    NOTE: If new modules were installed prior to the DTC being set, the module configuration can be incorrectly set during the PMI, or the PMI may not have been carried out.

    • CHECK the vehicle service history for recent service actions related to the TCM or PAM. If recent service history is found:

      • verify correct replacement module was installed

        • vehicle parts build may be used to verify correct part fitment

      • verify the configuration of replacement module was correct

        • re-configure module using as-built data if prior configuration is suspect

      • verify the module was not obtained from a like vehicle and installed into customer vehicle

        • return the swapped module to source vehicle and obtain new replacement module

        • if a new replacement module is installed, PERFORM PMI using as-built data

    • Operate the system and determine if the observable symptom is still present.

    Is the observable symptom present? 

    Yes  GO to  T8
    No  The system is operating correctly at this time. The concern may have been due to incorrect parts replacement procedures, or incorrect module configuration.

  9. T8 CHECK FOR CORRECT TCM (TRANSMISSION CONTROL MODULE) OPERATION

    • Ignition OFF.

    • Disconnect and inspect the TCM connectors.

    • Repair:

      • corrosion (install new connector or terminals - clean module pins)
      • damaged or bent pins - install new terminals/pins
      • pushed-out pins - install new pins as necessary

    • Reconnect the TCM connectors. Make sure they seat and latch correctly.

    • Operate the system and determine if the concern is still present.

    Is the concern still present? 

    Yes  CHECK OASIS for any applicable service articles: TSB, GSB, SSM or FSA. If a service article exists for this concern, DISCONTINUE this test and FOLLOW the service article instructions. If no service articles address this concern, INSTALL a new TCM
    No  The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.
scientia non olet · About LEMON Manuals