DTC Chart: Instrument Panel Cluster (IPC)
Diagnostics in this article assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .
DTC Chart - IPC
| DTC | Description | Action |
|---|---|---|
| B15A4:56 | Transmission Type Mismatch: Invalid/Incompatible Configuration | GO to Pinpoint Test CS |
| P0460:11 | Fuel Level Sensor "A" Circuit: Circuit Short To Ground | GO to Pinpoint Test D |
| P0460:13 | Fuel Level Sensor "A" Circuit: Circuit Open | GO to Pinpoint Test D |
| P1243:06 | Second Fuel Pump Fault or Ground Fault: Algorithm Based Failure | GO to Pinpoint Test D |
| P1346:11 | Fuel Level Sensor "B" Circuit: Circuit Short To Ground | GO to Pinpoint Test D |
| P1346:13 | Fuel Level Sensor "B" Circuit: Circuit Open | GO to Pinpoint Test D |
| P1534:01 | Restraint Deployment Indicator Circuit: General Electrical Failure | GO to Pinpoint Test BX |
| P1706:00 | High Vehicle Speed Observed in Park: No Sub Type Information | GO to Pinpoint Test X |
| U0100:00 | Lost Communication With ECM/PCM "A": No Sub Type Information | GO to Pinpoint Test BY |
| U0104:00 | Lost Communication With Cruise Control Module: No Sub Type Information | GO to Pinpoint Test CA |
| U0121:00 | Lost Communication With Anti-Lock Brake System (ABS) Control Module: No Sub Type Information | GO to Pinpoint Test CB |
| U0122:00 | Lost Communication With Vehicle Dynamics Control Module: No Sub Type Information | GO to Pinpoint Test CC |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test CD |
| U0146:00 | Lost Communication With Gateway "A": No Sub Type Information | GO to Pinpoint Test CF |
| U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | GO to Pinpoint Test CG |
| U0159:00 | Lost Communication With Parking Assist Control Module "A": No Sub Type Information | GO to Pinpoint Test CI |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to Pinpoint Test CJ |
| U0193:00 | Lost Communication With "Digital Audio Control Module A": No Sub Type Information | GO to Pinpoint Test CK |
| U0212:00 | Lost Communication With Steering Column Control Module: No Sub Type Information | GO to Pinpoint Test CL |
| U0212:82 | Lost Communication With Steering Column Control Module: Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test CL |
| U0232:00 | Lost Communication With Side Obstacle Detection Control Module - Left: No Sub Type Information | GO to Pinpoint Test CM |
| U0233:00 | Lost Communication With Side Obstacle Detection Control Module - Right: No Sub Type Information | GO to Pinpoint Test CM |
| U023A:00 | Lost Communication With Image Processing Module A: No Sub Type Information | GO to Pinpoint Test CN |
| U0253:00 | Lost Communication With Accessory Protocol Interface Module: No Sub Type Information | GO to Pinpoint Test CO |
| U0256:00 | Lost Communication With Front Controls Interface Module "A": No Sub Type Information | GO to Pinpoint Test CP |
| U0260:00 | Lost Communication With Seat Control Switch Module "A": No Sub Type Information | GO to Pinpoint Test CQ |
| U0401:00 | Invalid Data Received from ECM/PCM A: No Sub Type Information | GO to Pinpoint Test CR |
| U0401:81 | Invalid Data Received from ECM/PCM A: Invalid Serial Data Received | GO to Pinpoint Test CR |
| U0401:82 | Invalid Data Received from ECM/PCM A: Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test CR |
| U0401:86 | Invalid Data Received from ECM/PCM A: Signal Invalid | GO to Pinpoint Test CR |
| U0405:56 | Invalid Data Received From Cruise Control Module: Invalid/Incompatible Configuration | GO to Pinpoint Test CS |
| U0415:00 | Invalid Data Received From Anti-Lock Brake System (ABS) Control Module: No Sub Type Information | GO to Pinpoint Test CR |
| U0415:81 | Invalid Data Received From Anti-Lock Brake System (ABS) Control Module: Invalid Serial Data Received | GO to Pinpoint Test CR |
| U0415:82 | Invalid Data Received From Anti-Lock Brake System (ABS) Control Module: Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test CR |
| U0420:00 | Invalid Data Received From Power Steering Control Module: No Sub Type Information | GO to Pinpoint Test CR |
| U0420:82 | Invalid Data Received From Power Steering Control Module: Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test CR |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | GO to Pinpoint Test CR |
| U0424:80 | Invalid Data Received From HVAC Control Module: ISO/SAE Reserved | GO to Pinpoint Test CR |
| U0424:81 | Invalid Data Received From HVAC Control Module: Invalid Serial Data Received | GO to Pinpoint Test CR |
| U0424:82 | Invalid Data Received From HVAC Control Module: Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test CR |
| U0431:82 | Invalid Data Received From Body Control Module "A": Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test CR |
| U0452:81 | Invalid Data Received From Restraints Control Module: Invalid Serial Data Received | GO to Pinpoint Test CR |
| U0533:00 | Invalid Data Received From Side Obstacle Detection Control Module "A": No Sub Type Information | GO to Pinpoint Test CR |
| U0533:56 | Invalid Data Received From Side Obstacle Detection Control Module "A": Invalid/Incompatible Configuration | GO to Pinpoint Test CS |
| U0533:82 | Invalid Data Received From Side Obstacle Detection Control Module "A": Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test CR |
| U0534:00 | Invalid Data Received From Side Obstacle Detection Control Module "B": No Sub Type Information | GO to Pinpoint Test CR |
| U0534:56 | Invalid Data Received From Side Obstacle Detection Control Module "B": Invalid/Incompatible Configuration | GO to Pinpoint Test CS |
| U0534:82 | Invalid Data Received From Side Obstacle Detection Control Module "B": Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test CR |
| U0542:82 | Invalid Data Received From Headlamp Control Module "A": Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test CR |
| U0557:80 | Invalid Data Received From Front Controls Interface Module "A": ISO/SAE Reserved | GO to Pinpoint Test CR |
| U0557:81 | Invalid Data Received From Front Controls Interface Module "A": Invalid Serial Data Received | GO to Pinpoint Test CR |
| U0557:82 | Invalid Data Received From Front Controls Interface Module "A": Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test CR |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test CT |
| U3000:04 | Control Module: System Internal Failure | GO to Pinpoint Test CU |
| U3000:41 | Control Module: General Checksum Failure | GO to Pinpoint Test CU |
| U3000:42 | Control Module: General Memory Failure | GO to Pinpoint Test CU |
| U3000:44 | Control Module: Data Memory Failure | GO to Pinpoint Test CU |
| U3000:46 | Control Module: Calibration/Parameter Memory Failure | GO to Pinpoint Test CU |
| U3000:54 | Control Module: Missing Calibration | GO to Pinpoint Test CU |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test CV |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test CX |
| U300A:64 | Ignition Switch: Signal Plausibility Failure | GO to Pinpoint Test CZ |