Network Message Chart
Module Network Input Messages - IPC
| Broadcast Message | Originating Module | Message Purpose |
|---|---|---|
| ABS fault | ABS module | ABS input used to display the check brake system warning message. |
| Acceleration speed data | ABS module | Input used to control the exhaust mode feature display. Input used to control the acceleration timer feature display. Input used to control the brake performance display. Input used to control the lap timer display. |
| Adaptive cruise control gap distance display | IPMA | Input used to display the adaptive cruise control gap setting display. |
| Adaptive cruise control warning request | IPMA | Input used to display the adaptive cruise control message display. |
| Ambient air temperature data | PCM | Unfiltered ambient air temperature data used by the FCIM to calculate the outside air temperature. |
| Auto high beam status display | IPMA | Input used to control the auto high beam RTT indicator (digital IPC). |
| Battery low state of charge | BCM | Input used to control the charging system RTT indicator and the charging system fault message center warning message. |
| Body service required request | BCM | BCM controlled system faults input used to control the powertrain malfunction (wrench) RTT indicator. |
| Brake fluid level low message request | BCM | Input used to display the low brake fluid level warning message. |
| Brake (red) warning indicator request | ABS module | Input used to display the brake system fault warning message. |
| Brake pedal applied | PCM | Input used to control the brake performance display. |
| Camera status | IPMA | Input used to display the front camera malfunction warning message. |
| Convertible top message request | MRCMA | Input used to display the convertible top messages. |
| Cross traffic alert left status | SODL | Input used to control the BLIS off RTT indicator. Input used to control the blind spot information system message center messages. |
| Cross traffic alert right status | SODR | Input used to control the BLIS off RTT indicator. Input used to control the blind spot information system message center messages. |
| Cross traffic left sensor status | SODL | Input used to control the BLIS off RTT indicator. Input used to control the blind spot information system message center messages. |
| Cross traffic right sensor status | SODR | Input used to control the BLIS off RTT indicator. Input used to control the blind spot information system message center messages. |
| Cruise control override | PCM | Input used to control the ACC portion of the active driver assist system display. Input used to control the cruise control RTT indicator. |
| Cruise control set speed display | PCM | Input used to control the ACC portion of the active driver assist system display (digital IPC). Input used to control the cruise control set speed display. |
| Cruise control status | PCM | Input used to control the ACC portion of the active driver assist system display. Input used to control the cruise control RTT indicator. |
| Driver door ajar status | BCM | Input used to control the following: Door ajar RTT indicator. Driver door ajar message center warning message. Engine on warning message. Transmission not in park warning message. |
| Driver rear seatbelt buckle status | RCM | Input used to control the rear seatbelt monitor message. |
| Engine coolant temperature data | PCM | Used to control the engine over-temperature RTT indicator and the engine over-temperature message center warning message. |
| EPAS Failure | PSCM | Input used to display the EPAS messages. |
| Engine idle shutdown status | PCM | Input used to control and explain the reasons for the engine to shut down during idle conditions. |
| Engine oil life | PCM | Input used to display the engine oil life and oil change messages. |
| Engine oil life data reset | PCM | Input used to display the engine oil life and oil change messages. |
| Engine rpm data | PCM | Input used to control the low oil pressure RTT indicator. Input used to control the low oil pressure message center warning message. Input used to control the Average Fuel Economy (AFE)/DTE display. Input used to control the performance shift indication (digital IPC). |
| Engine service required request | PCM | Engine input used to control the powertrain malfunction (wrench) RTT. |
| Engine status | PCM | Input used to display the engine on warning message and the Average Fuel Economy (AFE)/DTE display. |
| Engine quiet mode | PCM | Input used to determine when to set the exhaust mode to the quiet mode based on driver settings. |
| Engine rev match status display | PCM | Input used to display the engine rev match mode track app. feature is enabled or disabled. |
| Forward collision warning indicator request | IPMA | Input used to display the forward collision warning. |
| Forward collision warning message request | IPMA | Input used to display the forward collision warning messages. |
| Forward distance status display | IPMA | Input used to control the forward collision display. |
| Fuel fill inlet message display | PCM | Input used to display the check fuel fill inlet message. |
| Fuel alcohol percent | PCM | Input used to display the Average Fuel Economy (AFE)/DTE. |
| Fuel flow volume display | PCM | Input used to display the Average Fuel Economy (AFE)/DTE. |
| Gas particulate filter status | PCM | Input used to display the gas particulate filter status messages (China). |
| Global clock data | BCM | Input used to control the quit time exhaust mode function. |
| GPS compass direction | APIM | Input used to display the vehicle compass heading. |
| Hill start assist status | ABS module | Input used to control the hill start assist not available message. |
| Hood ajar | BCM | Input used to control the hood ajar RTT and the hood ajar message center warning message. |
| Ignition key type | BCM | Input used to control the MyKey features. Input used to display the Average Fuel Economy (AFE)/DTE. |
| Ignition status | BCM | Input used for the following: To provide ignition RUN, START and ACC states. To display the transmission not in park warning message. To display the odometer. |
| Immobilizer message display | BCM | Input used to display the PATS, passive entry and key programming messages. |
| Lane keeping system status display | IPMA | Input used to control the lane keeping system display. |
| Lane keeping system hands off display | IPMA | Input used to display the lane keeping system hands off the steering wheel warning message. |
| Launch control status | PCM | Input used to control the launch control mode RTT indicator (analog IPC). Input used to control the launch control display. |
| Lock system message request | BCM | Input used to display the child lock, key battery low and security mode messages. |
| Luggage compartment lid ajar | BCM | Input used to control the door ajar RTT and the luggage compartment lid ajar message center warning message. |
| Manual upshift indicator (Europe only) | PCM | Input used to control the upshift RTT indicator. |
| Odometer count | PCM | Input used to display the Average Fuel Economy (AFE)/DTE display. Input used to control the odometer. Input used to control the lap timer display. |
| Oil pressure warning indicator request | PCM | Input used to control the low oil pressure RTT indicator and the low oil pressure message center warning message. |
| Outside air temperature | FCIM | Filtered ambient air temperature data used to display the outside air temperature (digital IPC). Input used to control the frost RTT indicator (Europe only). |
| Parking aid fault status | PAM | Input used to display the check parking aid message. |
| Parking aid rear status | PAM | Input used to display the parking aid on/off status message. |
| Parking brake status | BCM | Input used to display the parking brake applied warning message. |
| Passenger door ajar status | BCM | Input used to control the door ajar RTT indicator and the passenger door ajar message center warning message. |
| Passenger rear seatbelt buckle status | RCM | Input used to control the rear seatbelt monitor message. |
| Perimeter alarm chime request | BCM | Input used to display the start vehicle to stop alarm message. |
| Power pack status | PCM | Input used to display the Average Fuel Economy (AFE)/DTE. |
| Power shed level request | BCM | Input used to display the load shed messages. Input used to display the not-in-park warning message. |
| Powertrain drive mode | PCM | Input used to control the following drive mode Reconfigurable Telltales (RTT's): Drag strip Launch control Normal drive Sport Snow/wet Track Weather |
| Remote start status | BCM | Input used to display the remote start messages. |
| Seat memory command | DSM | Input used to display the memory seat operational messages. |
| Side obstacle detect status-left | SODL | Input used to control the BLIS off RTT indicator. Input used to display the BLIS warning messages. |
| Side obstacle detect status-right | SODR | Input used to control the BLIS off RTT indicator. Input used to display the BLIS warning messages. |
| Stability-traction control chime request | ABS module | Input used to display the service AdvanceTrac® message. |
| Starting system fault message request | PCM | Input used to display starting system messages. |
| Steering effort status | PSCM | Input used to control the steering mode RTT indicator (analog IPC). |
| Steering wheel message center switch data | SCCM | Input used to control the message center and audio menu selections. |
| Suspension driver mode status | VDM | Input used to control the vehicle dynamics (damper control) RTT indicator (analog IPC). |
| Tire pressure system placard data | BCM | Input used to display the individual tire pressures in the TPMS display. |
| Tire pressure system status | BCM | Input used to display the TPMS fault and tire training messages. |
| Track key mode | BCM | Input used to control the following: acceleration timer display. brake performance display. lap timer display. performance shift indication display (digital IPC). |
| Transmission gear display | PCM | Input used to display the not in park warning message. |
| Transmission gear display mode | PCM | Input used to display the engine on warning message. Input used to display the transmission not in park warning message. |
| Transmission service required | PCM | Transmission input used to control the powertrain malfunction (wrench) RTT indicator. |
| Transport mode | BCM | Input used to display the Average Fuel Economy (AFE)/DTE. Input used to display the factory and transport mode message and not in park warning message. Input used to display the not in park warning message. Input used to control the odometer. |
| Trip odometer verify | PCM | Input used to display the trip odometer. |
| Vehicle configuration data | BCM | Input used to display the odometer and the tire mobility kit expiration message. Input used to control the odometer. |
| Vehicle lateral acceleration | ABS module | Input used to display the accelerometer. Input used to control the brake performance display. |
| Vehicle longitudinal acceleration | ABS module | Input used to display the accelerometer. Input used to control the brake performance display. |
| Vehicle speed | PCM | Input used to control the Average Fuel Economy (AFE)/DTE display. Input used to control the digital speed display. Input used to control the engine on warning message. Input used to control the not in park warning message. Input used to control the overspeed warning RTT indicator (Gulf Cooperative Countries [GCC]). |
Module Network Input Messages - PCM
| Broadcast Message | Originating Module | Message Purpose |
|---|---|---|
| Engine oil life data reset | IPC | Input used to request the oil life minder reset. |
| Engine rev match request | IPC | Input used to enable the rev match track app. feature. |