LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2021 >> Mustang GT, Automatic Trans >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Drivers Assistance Systems - ADAS >> Parking Aid - Vehicles With: Rear Parking Aid >> Diagnosis And Testing >> Parking Aid >> DTC Chart(s) >> DTC Chart: PAM

DTC Chart: PAM

Diagnostics in this article assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .

PAM DTC Chart 

DTC Description Action
B1B44:12 Right Rear Outer Sensor: Circuit Short To Battery GO to Pinpoint Test D 
B1B44:14 Right Rear Outer Sensor: Circuit Short To Ground or Open GO to Pinpoint Test C 
B1B44:96 Right Rear Outer Sensor: Component Internal Failure GO to Pinpoint Test E 
B1B46:12 Right Rear Inner Sensor: Circuit Short To Battery GO to Pinpoint Test D 
B1B46:14 Right Rear Inner Sensor: Circuit Short To Ground or Open GO to Pinpoint Test C 
B1B46:96 Right Rear Inner Sensor: Component Internal Failure GO to Pinpoint Test E 
B1B48:12 Left Rear Outer Sensor: Circuit Short To Battery GO to Pinpoint Test D 
B1B48:14 Left Rear Outer Sensor: Circuit Short To Ground or Open GO to Pinpoint Test C 
B1B48:96 Left Rear Outer Sensor: Component Internal Failure GO to Pinpoint Test E 
B1B50:12 Left Rear Inner Sensor: Circuit Short To Battery GO to Pinpoint Test D 
B1B50:14 Left Rear Inner Sensor: Circuit Short To Ground or Open GO to Pinpoint Test C 
B1B50:96 Left Rear Inner Sensor: Component Internal Failure GO to Pinpoint Test E 
B1B58:11 Rear Sensors Power Circuit: Circuit Short To Ground GO to Pinpoint Test B 
U0100:00 Lost Communication With ECM/PCM "A": No Sub Type Information GO to Pinpoint Test F 
U0101:00 Lost Communication with TCM: No Sub Type Information GO to Pinpoint Test F 
U0121:00 Lost Communication With Anti-Lock Brake System (ABS) Control Module: No Sub Type Information GO to Pinpoint Test G 
U0131:00 Lost Communication With Power Steering Control Module: No Sub Type Information GO to Pinpoint Test H 
U0140:00 Lost Communication With Body Control Module: No Sub Type Information GO to Pinpoint Test I 
U0146:00 Lost Communication With Gateway "A": No Sub Type Information GO to Pinpoint Test J 
U0155:00 Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information GO to Pinpoint Test K 
U0212:00 Lost Communication With Steering Column Control Module: No Sub Type Information GO to Pinpoint Test L 
U0253:00 Lost Communication With Accessory Protocol Interface Module: No Sub Type Information GO to Pinpoint Test M 
U0256:00 Lost Communication With Front Controls Interface Module "A" GO to Pinpoint Test N 
U0257:00 Lost Communication With Front Controls/Display Interface Module: No Sub Type Information GO to Pinpoint Test O 
U0401:00 Invalid Data Received From ECM/PCM A: No Sub Type Information This DTC sets in continuous memory when the PAM receives invalid network data from the PCM with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network. If no PCM Diagnostic Trouble Codes (DTCs) are present, DIAGNOSE the observable symptom.
U0402:00 Invalid Data Received From TCM: No Sub Type Information This DTC sets in continuous memory when the PAM receives invalid network data from the PCM with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network. If no PCM Diagnostic Trouble Codes (DTCs) are present, DIAGNOSE the observable symptom.
U0415:00 Invalid Data Received From Anti-Lock Brake System (ABS) Control Module: No Sub Type Information This DTC sets in continuous memory when the PAM receives invalid network data from the ABS module with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network. If no ABS Diagnostic Trouble Codes (DTCs) are present, DIAGNOSE the observable symptom.
U0420:00 Invalid Data Received From Power Steering Control Module: No Sub Type Information This DTC sets in continuous memory when the PAM receives invalid network data from the PSCM with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network. If no PSCM Diagnostic Trouble Codes (DTCs) are present, DIAGNOSE the observable symptom.
U0422:00 Invalid Data Received From Body Control Module: No Sub Type Information This DTC sets in continuous memory when the PAM receives invalid network data from the BCM with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network. If no BCM Diagnostic Trouble Codes (DTCs) are present, DIAGNOSE the observable symptom.
U0423:00 Invalid Data Received from Instrument Panel Cluster Control Module: No Sub Type Information This DTC sets in continuous memory when the PAM receives invalid network data from the IPC with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network. If no IPC Diagnostic Trouble Codes (DTCs) are present, DIAGNOSE the observable symptom.
U0429:00 Invalid Data Received From Steering Column Control Module: No Sub Type Information This DTC sets in continuous memory when the PAM receives invalid network data from the SCCM with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network. If no SCCM Diagnostic Trouble Codes (DTCs) are present, DIAGNOSE the observable symptom.
U0554:00 Invalid Data Received From Accessory Protocol Interface Module: No Sub Type Information This DTC sets in continuous memory when the PAM receives invalid network data from the APIM with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network. If no APIM Diagnostic Trouble Codes (DTCs) are present, DIAGNOSE the observable symptom.
U0557:00 Invalid Data Received From Front Controls Interface Module "A": No Sub Type Information This DTC sets in continuous memory when the PAM receives invalid network data from the FCIM with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network. If no FCIMDiagnostic Trouble Codes (DTCs) are present, DIAGNOSE the observable symptom.
U0558:00 Invalid Data Received From Front Controls/Display Interface Module: No Sub Type Information This DTC sets in continuous memory when the PAM receives invalid network data from the FCDIM with a faulted signal data input. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the other modules on the network. If no FCDIM Diagnostic Trouble Codes (DTCs) are present, DIAGNOSE the observable symptom.
U2024:41 Control Module Cal-Config Data: General Checksum Failure CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the PAM self-test. If DTC U2024:41 is retrieved again, INSTALL As-Built data from Professional Technician Society (PTS), following the diagnostic scan tool instructions under Module Programming>As-Built. REFER to: Module Configuration - System Operation and Component Description . REPEAT the self-test. If DTC U2024:41 is retrieved again, INSTALL a new BCM. Refer to BODY CONTROL MODULE (BCM)
U2100:00 Initial Configuration Not Complete: No Sub Type Information CHECK the vehicle service history for recent service actions related to this module. This DTC can set due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, INSTALL As-Built data from Professional Technician Society (PTS), following the diagnostic scan tool instructions under Module Programming>As-Built. REFER to: Module Configuration - System Operation and Component Description . If there have been no recent service actions, INSTALL a new BCM. Refer to BODY CONTROL MODULE (BCM)
U2101:00 Control Module Configuration Incompatible: No Sub Type Information CHECK the vehicle service history for recent service actions related to this module. This DTC can set due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, INSTALL As-Built data from Professional Technician Society (PTS), following the diagnostic scan tool instructions under Module Programming>As-Built. REFER to: Module Configuration - System Operation and Component Description . If there have been no recent service actions, INSTALL a new BCM. Refer to BODY CONTROL MODULE (BCM)
U3000:44 Control Module: Data Memory Failure CLEAR the PAM Diagnostic Trouble Codes (DTCs) and PERFORM the PAM self-test. If DTC U3000:44 is retrieved again, INSTALL a new BCM. Refer to BODY CONTROL MODULE (BCM)
U3000:45 Control Module: Program Memory Failure CLEAR the PAM Diagnostic Trouble Codes (DTCs) and PERFORM the PAM self-test. If DTC U3000:45 is retrieved again, INSTALL a new BCM. Refer to BODY CONTROL MODULE (BCM)
U3000:46 Control Module: Calibration/Parameter Memory Failure CLEAR the PAM Diagnostic Trouble Codes (DTCs) and PERFORM the PAM self-test. If DTC U3000:46 is retrieved again, INSTALL a new BCM. Refer to BODY CONTROL MODULE (BCM) .
U3000:49 Control Module: Internal Electronic Failure ADDRESS all other Diagnostic Trouble Codes (DTCs) first. CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U3000:49 is retrieved again, INSTALL a new BCM. Refer to BODY CONTROL MODULE (BCM) .
scientia non olet · About LEMON Manuals