LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2021 >> Explorer Limited Hybrid, 4WD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 8 (Automatic Transmission - 10-Speed Automatic Transmission - 10R60 (2 Of 3)) >> Diagnosis And Testing >> DTC Chart and Pinpoint Tests - 3.3L Duratec-V6 >> Pinpoint Tests >> Pinpoint Test X : DTC P0751, P0756, P0761, P0766, P0771, P2707

Pinpoint Test X : DTC P0751, P0756, P0761, P0766, P0771, P2707

WARNING: This page is about a different variant/trim than selected.
  1. Normal Operation and Fault Conditions 

    The PCM monitors clutch applications. It sets a DTC if it detects a non-electrical fault that causes a clutch to fail to apply.

    DTC Fault Trigger Conditions 

    DTC Description Fault Trigger Condition
    PCM P0751:00 Shift Solenoid "A" Performance/Stuck Off: No Sub Type Information DTC P0751 is a non-electrical failure indicating the A clutch failed to apply. When this DTC sets the failsafe logic disables all gears that use clutch A. Clutch A is used for 1st through 6th gears and only allows 7 through 10 gears.
    PCM P0756:00 Shift Solenoid "B" Performance/Stuck Off: No Sub Type Information DTC P0756 is a non-electrical failure indicating the B clutch failed to apply. When this DTC sets the failsafe logic disables all gears that use clutch B. Clutch B is on in Reverse, 1st and 2nd gears with engine braking, 8th, 9th and 10th gears.
    PCM P0761:00 Shift Solenoid "C" Performance/Stuck Off: No Sub Type Information DTC P0761 is a non-electrical failure indicating the C clutch failed to apply. When this DTC sets the failsafe logic disables all gears that use clutch C. Clutch C is used for 2nd, 3rd, 4th, 5th, 7th, 9th and 10th gears, so it only allows 6th, 8th and R.
    PCM P0766:00 Shift Solenoid "D" Performance/Stuck Off: No Sub Type Information DTC P0751 is a non-electrical failure indicating the D clutch failed to apply. When this DTC sets the failsafe logic disables all gears that use clutch D. Clutch D is used for R, 2nd, 3rd, 4th, 6th, 7th, 8th and 10th gears, so it only allows 5th, 9th gears.
    PCM P0771:00 Shift Solenoid "E" Performance/Stuck Off: No Sub Type Information DTC P0751 is a non-electrical failure indicating the E clutch failed to apply. When this DTC sets the failsafe logic disables all gears that use clutch E. Clutch E is used for 1st, 3rd, 5th, 6th, 7th, 8th, and 9th gear. and only allows 2nd, 4th, 10th, and R gears.
    PCM P2707:00 Shift Solenoid "F" Performance/Stuck Off: No Sub Type Information DTC P0751 is a non-electrical failure indicating the F clutch failed to apply. When this DTC sets the failsafe logic disables all gears that use clutch F. Clutch F is used for R, 4M, 5M, 6M, 7M, 8M, 9M, 10M.

    Possible Sources 

    • Shift solenoid stuck off
    • Stuck control valve
    • Contamination in the main control
    • Clutch damaged
    • Faulty seal

  2. X1 CHECK FOR DIAGNOSTIC TROUBLE CODES (DTCS)

    • Using a diagnostic scan tool, clear the DTC from the PCM.

    • Road test the vehicle.

    • Using a diagnostic scan tool, retrieve all PCM continuous memory diagnostic trouble codes (CMDTCs).

    Are Diagnostic Trouble Code (DTC) P0751, P0756, P0761, P0766, P0771, P2707 present in the PCM? 

    Yes  For DTC P0751, For A clutch Does Not Apply symptom, REFER to: A Clutch . For DTC P0756, For B clutch Does Not Apply symptom, REFER to: B Clutch . For DTC P0761, For C clutch Does Not Apply symptom, REFER to: C Clutch . For DTC P0766, For D clutch Does Not Apply symptom, REFER to: D Clutch . For DTC P0771, For E clutch Does Not Apply symptom, REFER to: E Clutch . For DTC P2707, For F clutch Does Not Apply symptom, REFER to: F Clutch .
    No  The fault is not present at this time and may be intermittent.
scientia non olet · About LEMON Manuals