LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2021 >> Explorer Limited Hybrid, 4WD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 20 (Automatic Transmission External Controls - 10-Speed Automatic Transmission - 10R60) >> Diagnosis And Testing >> External Controls >> Pinpoint Tests >> Pinpoint Test F : DTC U0121

Pinpoint Test F : DTC U0121

WARNING: This page is about a different variant/trim than selected.
  1. Refer to Module Communications Network for schematic and connector information.

    Normal Operation and Fault Conditions 

    The GSM and ABS module use information contained in messages on the HS-CAN.

    DTC Fault Trigger Conditions 

    DTC Description Fault Trigger Condition
    GSM U0121:00 Lost Communication With Anti-Lock Brake System (ABS) Control Module "A": No Sub Type Information This DTC sets if the GSM detects data messages received from the ABS module are missing.

    Possible Sources 

    • Communication concern
    • ABS
    • GSM

  2. F1 VERIFY THE SCAN TOOL COMMUNICATES WITH THE ABS (ANTI-LOCK BRAKE SYSTEM)

    • Connect the diagnostic scan tool.

    • Check that a vehicle session can be established using the scan tool.

    Can a vehicle session be established? 

    Yes  GO to  F2
    No  REFER to: Communications Network .

  3. F2 CHECK THE GSM (GEAR SHIFT MODULE) CONTINUOUS MEMORY DIAGNOSTIC TROUBLE CODES (CMDTCS)

    • Ignition ON.

    • Using a diagnostic scan tool, perform the GSM self-test.

    • Clear the DTCs.

    • Wait 10 seconds.

    • Repeat the GSM self-test.

    Are any non-network DTCs present? 

    Yes  DIAGNOSE all non-network DTCs. REFER to Diagnostic Trouble Code (DTC) Chart .
    No  GO to  F3

  4. F3 PERFORM THE ABS (ANTI-LOCK BRAKE SYSTEM) SELF-TEST

    • Using a diagnostic scan tool, perform the ABS self-test.

    Are any non-network DTCs present? 

    Yes  DIAGNOSE all non-network DTCs. REFER to: Anti-Lock Brake System (ABS) and Stability Control .
    No  GO to  F4

  5. F4 CHECK THE GWM (GATEWAY MODULE A) DIAGNOSTIC TROUBLE CODES (DTCS)

    • Using a diagnostic scan tool, check the GWM Continuous Memory Diagnostic Trouble Codes (CMDTCs).

    Are any DTCs set? 

    Yes  REFER to: Communications Network .
    No  GO to  F5

  6. F5 RECHECK THE GSM (GEAR SHIFT MODULE) DIAGNOSTIC TROUBLE CODES (DTCS)

    • Using a diagnostic scan tool, clear the GSM DTCs.

    • Ignition OFF.

    • Ignition ON.

    • Wait 10 seconds.

    • Using a diagnostic scan tool, perform the continuous memory self-test.

    • Check the GSM DTCs.

    Is DTC U0121 still present? 

    Yes  GO to  F6
    No  The system is operating correctly at this time. The DTC may have set due to high network traffic or an intermittent fault condition.

  7. F6 CHECK FOR OTHER CAUSES OF NETWORK COMMUNICATION CONCERNS

    NOTE: If new modules were installed prior to the DTC being set, the module configuration can be incorrectly set during the PMI or the PMI may not have been carried out.

    • CHECK the vehicle service history for recent service actions related to the ABS or AWD. If recent service history is found:

      • verify correct replacement module was installed

        • HVBOM may be used to verify correct part application

      • verify the configuration of replacement module was correct

        • re-configure module using as-built data if prior configuration is suspect

      • verify the module was not obtained from a like vehicle and installed into customer vehicle

        • return the swapped module to source vehicle and obtain new replacement module

    • Operate the system and determine if the observable symptom is still present.

    Is the observable symptom still present? 

    Yes  GO to  F7
    No  The system is operating correctly at this time. The concern may have been due to incorrect parts replacement procedures or incorrect module configuration.

  8. F7 CHECK FOR CORRECT ABS (ANTI-LOCK BRAKE SYSTEM) OPERATION

    • Ignition OFF.

    • Disconnect and inspect the ABS and related in-line connectors.

    • Repair:

      • corrosion (install new connector or terminals - clean module pins)
      • damaged or bent pins - install new terminals/pins
      • pushed-out pins - install new pins as necessary

    • Reconnect the ABS and all related in-line connectors. Make sure they seat and latch correctly.

    • Operate the system and determine if the concern is still present.

    Is the concern still present? 

    Yes  CHECK OASIS for any applicable service articles: TSB, GSB (general service bulletin), SSM (special service message) or FSA (Field Service Action). If a service article exists for this concern, DISCONTINUE this test and FOLLOW the service article instructions. If no service articles address this concern, Refer to ABS Guided Routine .
    No  The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.
scientia non olet · About LEMON Manuals