RTT Indicators

NOTE: It is important to view each of the cluster options in the Overview to identify which IPC uses a specific RTT indicator.

Refer to: Instrument Panel Cluster (IPC) - Overview .

4WD (2H, 4L, 4H And 4A)

The IPC provides RTT indicators to inform the driver of the status of the 4WD system state. The IPC receives the 4x2, 4WD high, 4WD low and 4WD auto status messages from the GWM over the HS-CAN3. The GWM receives the 4x2, 4WD high, 4WD low and 4WD auto status messages from the TCCM over the HS-CAN2.

Auto High Beam

The IPC provides the auto high beam RTT indicator to inform the driver the auto high beam function is turned on and the high beam status may automatically change. The IPC receives the auto high beam indication request message from the GWM over the HS-CAN3. The GWM receives the auto high beam indication request message from the IPMA over the HS-CAN2.

Auto Stop-Start

The IPC provides the auto stop-start RTT indicator along with multiple messages displayed at various times throughout the auto stop-start system operation to inform the driver of the system status and to provide direction when driver intervention is required. The IPC receives the stop-start standby indicator request and stop-start message request from the GWM over the HS-CAN3. The GWM receives the stop-start standby indicator request and stop-start message request from the PCM over the HS-CAN1.

The auto stop-start indicator informs the driver of the following states:

Indicator Status	System Status
Solid green	The auto stop-start feature has temporarily turned off the engine.
Solid amber	A stop-start system concern exists.
Flash in either green or amber	A system state as determined by the PCM.
Grayed out (mid-level and high-level IPC)	Indicates the auto stop-start feature is not available.

BLIS Off

The IPC provides a RTT indicator to inform the driver the BLIS is turned off.

The IPC receives all network messages required to operate the BLISRTT indicator from the GWM over the HS-CAN3.

The GWM receives the cross traffic alert left status, side obstacle detect status-left and the BLIS trailer tow left status messages from the SODL over the MS-CAN.

The GWM receives the cross traffic alert right status, side obstacle status-right and the BLIS trailer tow right status messages from the SODR over the MS-CAN.

Charging System Message Center Displays

The IPC provides a charging system RTT warning indicator along with message displays indicating the status of the charging system. When a fault is present in the charging system, the BCM sends the battery low state of charge message to display message center warning messages and the charging system RTT warning indicator.

The IPC receives the battery low state of charge message from the GWM over the HS-CAN3. The GWM receives the battery low state of charge message from the BCM over the HS-CAN1.

Cruise Control

The cruise control RTT indicator informs the driver of the cruise control status (off, active or standby). When off, the cruise control RTT indicator is not displayed. When the cruise control system is active, the cruise control RTT indicator turns green and turns gray when in standby.

The IPC uses cruise control status, cruise control set speed request and cruise control override messaged inputs to control the cruise control RTT indicator.

The IPC receives the cruise control status, cruise control set speed request and cruise control override messages from the GWM over the HS-CAN3.

The GWM receives the cruise control status, cruise control set speed request and cruise control override messages from the PCM over the HS-CAN1.

Door, Hood Or Liftgate Ajar

The IPC provides a door ajar, hood ajar and liftgate ajar RTT warning indicators along with message displays to indicate the status of the doors. The BCM monitors each of the ajar inputs (driver, passenger, left rear, right rear, hood and liftgate) and sends a door ajar status (driver door ajar status, passenger door ajar status, left rear door ajar status, right rear door ajar status, hood ajar status or liftgate ajar status) message to the GWM over the HS-CAN1. The IPC receives the driver door ajar status, passenger door ajar status, left rear door ajar status, right rear door ajar, hood ajar status or liftgate status messages from the GWM over the HS-CAN3 to display the specific ajar RTT indicator and corresponding warning message.

ECO Select Mode

The ECO Select selectable drive mode RTT indicator informs the driver the vehicle is operating in economy mode based on the driver requested input. The IPC receives the selectable drive mode request message from the GWM over the HS-CAN3. The GWM receives the selectable drive mode request message from the ABS module over the HS-CAN2.

Electronic Park Brake

The electronic park brake RTT indicator indicates a fault in the electronic park brake system. The IPC receives the electronic park brake (yellow) indicator request from the GWM over the HS-CAN3. The GWM receives the electronic park brake (yellow) indicator request from the ABS module over the HS-CAN2.

Electronic Limited Slip Differential (eLSD)

The IPC receives the rear differential indicator request message from the GWM over the HS-CAN3. The GWM receives the rear differential indicator request message from the PCM over the HS-CAN1.

If the vehicle is shifted into Electronic Limited Slip Differential (eLSD) mode, the DCMR sends the IPC the rear differential status display message to illuminate the Electronic Limited Slip Differential (eLSD) RTT indicator. If the vehicle is shifted out of Electronic Limited Slip Differential (eLSD) mode, the DCMR sends the IPC the rear differential status display message to turn off the Electronic Limited Slip Differential (eLSD) RTT indicator, informing the driver the vehicle has shifted out of Electronic Limited Slip Differential (eLSD) mode.

Engine Over-Temperature

The IPC provides the engine over-temperature RTT warning indicator to alert the driver the engine is over temperature. The IPC receives the engine overheat indication request and the engine coolant temperature data from the GWM over the HS-CAN3. The GWM receives the engine overheat indication request and the engine over-temperature message from the PCM over the HS-CAN1.

Front Fog Lamp

The front fog lamp RTT indicator informs the driver that the front fog lamps are turned on. The IPC receives the front fog lamp indicator request from the GWM over the HS-CAN3. The GWM receives the front fog lamp indicator request from the BCM module over the HS-CAN1.

Grass/Gravel/Snow (4WD)

The grass/gravel/snow RTT indicator informs the driver the vehicle is operating in grass/gravel/snow mode based on the driver requested input. The IPC receives the selectable drive mode request message from the GWM over the HS-CAN3. The GWM receives the selectable drive mode request message from the ABS module over the HS-CAN2.

High Beam

The IPC provides the high beam RTT indicator to indicate to the driver that the high beam headlamps are on. The IPC receives the headlamp high/low beam status message from the GWM over the HS-CAN3. The GWM receives the headlamp high/low beam status message from the BCM over the HS-CAN1.

Hill Descent

The IPC provides the hill descent RTT indicator to indicate to the driver that the hill descent control is on. The IPC receives the hill descent message request from the GWM over the HS-CAN3. The GWM receives the hill descent message request from ABS module over the HS-CAN2.

LH - RH Turn Signal/Hazard

When the multifunction switch is in the LH or RH turn position or if the hazard switch is on, the BCM sends the right turn lamp on request, the left turn lamp on request or both messages to the GWM over the HS-CAN1. The GWM sends the right turn lamp on request, the left turn lamp on request or both messages to the IPC over the HS-CAN3. Upon receipt of the applicable turn signal on/off data, the IPC flashes the turn signal RTT indicator on and off.

Lights On

When the parking lamps are turned on, the BCM sends the parklamp status message to the GWM over the HS-CAN1. The IPC receives the parklamp status message from the GWM over the HS-CAN3 to illuminate the lights on RTT indicator.

Low Fuel

The IPC provides the low fuel RTT indicator to indicate the fuel level is low at several preset stages before the driver runs out of fuel. The low fuel RTT indicator is displayed in 2 colors, amber and red depending on the remaining fuel range. The IPC uses the calculated DTE to control the low fuel RTT indicator. When the fuel level reaches approximately 120 km (75 miles) (MyKey® users only) and 80 km (50 miles), 40 km (25 miles), 20 km (10 miles) and 0 km (0 miles) for MyKey® and administrator key users, the IPC turns on the low fuel RTT indicator.

Low Engine Oil Pressure

The IPC uses the engine oil pressure warning indicator request and engine rpm data to control the low engine oil pressure indicator. The engine oil pressure switch is hardwired to the PCM. The PCM provides the oil pressure warning indicator request and the engine rpm data to the GWM over the HS-CAN1. The GWM provides the oil pressure warning indicator request and engine rpm data to the IPC over the HS-CAN3. The IPC requires engine rpm above 400 rpm before the message center displays the low oil pressure RTT indicator.

Low Washer Fluid Level

The low washer fluid level switch is hardwired to the IPC through a single signal circuit and is grounded through a separate ground circuit. The IPC provides a reference voltage to the washer fluid level switch. When the washer fluid is low, the washer fluid level switch closes to ground, pulling the reference voltage low. When the IPC detects the washer fluid input is pulled low, the low washer fluid level RTT indicator illuminates.

Overspeed Warning (Gulf Cooperative Countries [GCC])

The IPC provides an overspeed RTT warning indicator to inform the driver that the vehicle speed has reached or exceeded the 120 km/h (75 mph) threshold. The IPC receives the vehicle speed signal from the GWM over the HS-CAN3. The GWM receives the vehicle speed signal from the PCM over the HS-CAN1.

Powertrain Malfunction (Wrench)

The IPC provides a powertrain malfunction (wrench) message center RTT indicator to indicate transmission, Electronic Throttle Control (ETC), 4WD, and BCM concerns.

The IPC receives all the required messages from the GWM over the HS-CAN3.

The GWM receives the transmission service required message from the TCM over the HS-CAN1.

The GWM receives the engine service required message from the PCM over the HS-CAN1.

The GWM receives the 4WD service required and 4WD status display messages from the TCCM over the HS-CAN2.

The GWM receives the gearshift module service required message from the GSM over the HS-CAN2.

The GWM receives the body service required message from the BCM over the HS-CAN1.

PRNDL/Progressive Range Select And SelectShift®

The progressive range select display provides a numerical display of the lower transmission ranges and indicates to the driver which gear is currently selected when the driver has manually shifted to a lower range 1-10. The SelectShift® display indicates to the driver which gear is currently selected when the transmission is in the SelectShift® mode. When the transmission is in SelectShift® mode, the gear number is displayed in the SelectShift® display area.

The progressive range select and SelectShift® display behavior changes based on each IPC design. The base IPC shows the range select in the menu on-demand screen and in popup windows with the transmission gears listed in the center of the display and the selected gear in the the upper left corner (the first digit is the selected gear and the second digit is the number of gears).

For all Instrument Panel Clusters (IPCs), the display changes depending on the driver selections (range select or SelectShift®) and for the mid-level and high-level Instrument Panel Clusters (IPCs), whether indicators are displayed in the lower portions of the display area. To view where the display area is located on the mid-level and high-level Instrument Panel Clusters (IPCs), Refer to: Instrument Panel Cluster (IPC) - Overview .

For additional information related to the progressive range select or SelectShift® features, refer to the Owner's Literature.

The IPC uses the following messages to control the PRNDL/progressive range select and SelectShift® indication.

Battery shed level request
Transport mode
Transmission gear display
Transmission gear display mode
Vehicle speed

The IPC receives all related messages from the GWM over the HS-CAN3.

The GWM receives the transmission gear display and transmission gear display mode messages from the TCM over the HS-CAN1.

The GWM receives the vehicle speed message from the PCM over the HS-CAN1.

The GWM receives the transport mode and battery shed level request messages from the BCM over the HS-CAN1.

The IPC also uses a park detect switch (part of the selector lever, if equipped) input to signal the IPC the shift lever is fully seated in the PARK (P) position. The IPC compares the park detect switch input with the park status in the transmission gear position message sent from the PCM. The IPC provides a battery reference voltage to the park detect switch. When the selector lever is in PARK (P), the park detect switch routes the reference voltage to ground, pulling the circuit low to the IPC. When the selector lever is moved out of PARK (P), the park detect switch opens to ground, sending the reference voltage high.

Sand (4WD)

The sand RTT indicator informs the driver the vehicle is operating in sand mode based on the driver requested input. The IPC receives the selectable drive mode request message from the GWM over the HS-CAN3. The GWM receives the selectable drive mode request message from the ABS module over the HS-CAN2.

Snow/Wet Mode

The snow/wet mode RTT indicator informs the driver the vehicle is operating in snow/wet mode based on the driver requested input. The IPC receives the selectable drive mode request message from the GWM over the HS-CAN3. The GWM receives the selectable drive mode request message from the ABS module over the HS-CAN2.

Sport Mode

The sport mode RTT indicator informs the driver the vehicle is operating in sport mode mode based on the driver requested input. The IPC receives the selectable drive mode request message from the GWM over the HS-CAN3. The GWM receives the selectable drive mode request message from the ABS module over the HS-CAN2.

Stability-Traction Control Disabled (Sliding Car OFF Icon)

When the driver enables or disables the stability-traction control system, the ABS module sends the traction control off indicator request message to the GWM over the HS-CAN2. The GWM sends the traction control off indicator request message to the IPC over the HS-CAN3 to illuminate or turn off the traction control disabled RTT indicator (sliding car OFF icon) based upon the system state.

Refer to ABS/Brake/Stability-Traction Control System Indication description in Indicators for information on the conditions when the stability-traction control disabled indicator (sliding car OFF icon) is turned on. Refer to: Instrument Panel Cluster (IPC) - System Operation and Component Description .

When a MyKey® administrator has set the AdvanceTrac® feature to always on and a MyKey® programmed key is in use, the stability-traction control system cannot be disabled. The menu selection in the message center used to disable the stability-traction control system does not display when a MyKey® is in use, but remains active for the MyKey® administrator to select the AdvanceTrac® always on feature off. The stability-traction control indicator still functions normally to indicate a stability-traction control system fault and a stability-traction control active event.

Refer to ABS/Brake/Stability-Traction Control System Indication description in Indicators for information on the conditions when the stability-traction control RTT indicator (sliding car Off icon) is turned on. Refer to: Instrument Panel Cluster (IPC) - System Operation and Component Description .

Stability-Traction Control (Sliding Car Icon)

The IPC receives the stability-traction control indicator request message from the GWM over the HS-CAN3. The GWM receives the stability-traction control indicator request message from the ABS module over the HS-CAN2.

Refer to ABS/Brake/Stability-Traction Control System Indication description in Indicators for information on the conditions when the stability-traction control RTT indicator (sliding car icon) is turned on. Refer to: Instrument Panel Cluster (IPC) - System Operation and Component Description .

Tow Haul

The tow haul RTT indicator informs the driver the vehicle is operating in tow haul mode based on the driver requested input. The IPC receives the selectable drive mode request message from the GWM over the HS-CAN3. The GWM receives the selectable drive mode request message from the ABS module over the HS-CAN2.

TPMS

The IPC receives the tire pressure warning indicator message from the GWM over the HS-CAN3. The GWM receives the tire pressure warning indicator message from the BCM over the HS-CAN1.

If the BCM determines the tire pressure has exceeded the low tire pressure limits, the tire pressure warning indicator request message is sent to the IPC to illuminate the TPMSRTT indicator.

If a TPMS monitor or sensor fault condition exists, the BCM sends the tire pressure warning indicator message to the IPC to flash the TPMSRTT indicator. The IPC flashes the TPMS warning indicator for 75 seconds then turns the indicator on solid.