Pinpoint Test I: There Is An Active Park Assist Fault Message Shown In The CENTERSTACK Infotainment Display And/Or In The IPC (Instrument Panel Cluster) Message Center Display
- I1 PERFORM A NETWORK TEST
- Ignition ON.
- Using a diagnostic scan tool, perform a network test.
Do all modules pass the network test?
Yes GO to I2 No Refer to: Communications Network . - I2 CHECK THE PAM (PARKING ASSIST CONTROL MODULE) DIAGNOSTIC TROUBLE CODES (DTCS)
- Using a diagnostic scan tool, perform the PAM self-test.
Are any Diagnostic Trouble Codes (DTCs) present?
Yes Refer to the PAM DTC Chart . No GO to I3 - I3 CHECK THE PSCM (POWER STEERING CONTROL MODULE) DIAGNOSTIC TROUBLE CODES (DTCS)
- Using a diagnostic scan tool, perform the PSCM self-test.
Are any Diagnostic Trouble Codes (DTCs) present?
Yes Refer to: Power Steering . No GO to I4 - I4 CHECK THE SCCM (STEERING COLUMN CONTROL MODULE) DIAGNOSTIC TROUBLE CODES (DTCS)
- Using a diagnostic scan tool, perform the SCCM self-test.
Are any Diagnostic Trouble Codes (DTCs) present?
Yes Refer to: Steering Wheel and Column Electrical Components . No GO to I5 - I5 CHECK THE ABS (ANTI-LOCK BRAKE SYSTEM) MODULE DIAGNOSTIC TROUBLE CODES (DTCS)
- Using a diagnostic scan tool, perform the ABS module self-test.
Are any Diagnostic Trouble Codes (DTCs) present?
Yes Refer to: Anti-Lock Brake System (ABS) and Stability Control . No GO to I6 - I6 CHECK THE PCM (POWERTRAIN CONTROL MODULE) DIAGNOSTIC TROUBLE CODES (DTCS)
- Using a diagnostic scan tool, perform the PCM self-test.
Are any Diagnostic Trouble Codes (DTCs) present?
Yes See Electronic Engine Control, PCMDTC Chart. Refer to: Electronic Engine Controls . No GO to I7 - I7 CHECK THE RCM (RESTRAINTS CONTROL MODULE) DIAGNOSTIC TROUBLE CODES (DTCS)
- Using a diagnostic scan tool, perform the RCM self-test.
Are any Diagnostic Trouble Codes (DTCs) present?
Yes Refer to: Airbag Supplemental Restraint System (SRS) . No GO to I8 - I8 CHECK THE IPC (INSTRUMENT PANEL CLUSTER) DIAGNOSTIC TROUBLE CODES (DTCS)
- Using a diagnostic scan tool, perform the IPC self-test.
Are any Diagnostic Trouble Codes (DTCs) present?
Yes Refer to: Instrumentation, Message Center and Warning Chimes . No GO to I9 - I9 CHECK THE GWM (GATEWAY MODULE A) CONTINUOUS MEMORY DIAGNOSTIC TROUBLE CODES (CMDTCS)
- Using a diagnostic scan tool, check the GWM Continuous Memory Diagnostic Trouble Codes (CMDTCs).
Are any Diagnostic Trouble Codes (DTCs) present?
Yes Refer to: Communications Network . No GO to I10 - I10 CHECK THE BCM (BODY CONTROL MODULE) DIAGNOSTIC TROUBLE CODES (DTCS)
- Using a diagnostic scan tool, perform the BCM self-test.
Are any Diagnostic Trouble Codes (DTCs) present?
Yes Refer to: Body Control Module (BCM) . No GO to I11 - I11 CHECK THE APIM (SYNC MODULE) DIAGNOSTIC TROUBLE CODES (DTCS)
- Using a diagnostic scan tool, perform the APIM self-test.
Are any Diagnostic Trouble Codes (DTCs) present?
Yes Refer to: Information and Entertainment System . No GO to I12 - I12 CHECK FOR CORRECT PAM (PARKING ASSIST CONTROL MODULE) OPERATION
- Ignition OFF.
- Disconnect and inspect all PAM connectors.
- Repair:
- corrosion (install new connector or terminals - clean module pins)
- damaged or bent pins - install new terminals/pins
- pushed-out pins - install new pins as necessary
- Reconnect the PAM connectors. Make sure they seat and latch correctly.
- Operate the system and determine if the concern is still present.
Is the concern still present?
Yes CHECK OASIS for any applicable service articles: TSB, GSB, SSM or FSA. If a service article exists for this concern, DISCONTINUE this test and FOLLOW the service article instructions. If no service articles address this concern, INSTALL a new PAM. Refer to: Parking Assist Control Module (PAM) . No The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector. ADDRESS the root cause of any connector or pin issues.