LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2021 >> Escape Titanium Plug-In Hybrid >> Repair and Diagnosis >> Electrical >> Gauges >> Instrumentation, Message Center And Warning Chimes (2 Of 2) >> Diagnosis And Testing >> Instrumentation, Message Center and Warning Chimes >> Pinpoint Tests >> Pinpoint Test Be: The Auto High Beam RTT (RECONFIGURABLE Telltale) Indicator Is Never Or Always On

Pinpoint Test Be: The Auto High Beam RTT (RECONFIGURABLE Telltale) Indicator Is Never Or Always On

  1. Normal Operation and Fault Conditions 

    See Auto High Beam. REFER to: Instrument Panel Cluster (IPC) - System Operation and Component Description .

    If the auto high beam indication request message is missing for less than 5 seconds, the IPC defaults the auto high beam RTT indicator to its last indication state (on or off), based upon the last message received.

    If the auto high beam indication request message is missing for 5 seconds or longer, the IPC defaults the auto high beam RTT indicator off.

    Possible Sources 

    • Communication concern
    • GWM
    • IPMA
    • IPC

  2. BE1 CHECK THE MESSAGE CENTER OPERATION

    • Ignition ON.

    • Close all doors, liftgate and the hood.

    • Clear all message center warnings by pressing the OK button for each warning present.

    • Monitor the door ajar RTT warning indicator.

    • Open the driver door.

    • Clear the message center popup warning.

    • Monitor the door ajar RTT warning indicator.

    Is the door ajar RTT warning indicator off with the door closed, and on with the door open? 

    Yes  GO to  BE2
    No  GO to Pinpoint Test A 

  3. BE2 CHECK THE AUTO HIGH BEAMS OPERATION

    • Verify the auto high beams operate.

    Do the auto high beams operate correctly? 

    Yes  GO to  BE3
    No  DIAGNOSE the auto high beams. REFER to: Headlamps

  4. BE3 PERFORM THE IPC (INSTRUMENT PANEL CLUSTER) SELF-TEST

    • Ignition ON.

    • Using a diagnostic scan tool, perform the IPC self-test.

    Are any Diagnostic Trouble Codes (DTCs) recorded? 

    Yes  REFER to the IPC DTC Chart.
    No  GO to  BE4

  5. BE4 CHECK THE GWM (GATEWAY MODULE A) DIAGNOSTIC TROUBLE CODES (DTCS)

    • Using a diagnostic scan tool, check the GWM Continuous Memory Diagnostic Trouble Codes (DTCs).

    Are any Diagnostic Trouble Codes (DTCs) recorded? 

    Yes  REFER to: Communications Network
    No  GO to  BE5

  6. BE5 PERFORM THE IPMA (IMAGE PROCESSING MODULE A) SELF-TEST

    • Ignition ON.

    • Using a diagnostic scan tool, perform the IPMA self-test.

    Are any Diagnostic Trouble Codes (DTCs) recorded? 

    Yes  REFER to the Master DTC Chart.
    No  GO to  BE6

  7. BE6 CHECK FOR CORRECT IPC (INSTRUMENT PANEL CLUSTER) OPERATION

    • Ignition OFF.

    • Disconnect and inspect the IPC connector.

    • Repair:

      • corrosion (install new connector or terminals - clean module pins)
      • damaged or bent pins - install new terminals/pins
      • pushed-out pins - install new pins as necessary

    • Reconnect the IPC connector. Make sure it seats and latches correctly.

    • Operate the system and determine if the concern is still present.

    Is the concern still present? 

    Yes  CHECK OASIS for any applicable service articles: TSB, GSB, SSM or FSA. If a service article exists for this concern, DISCONTINUE this test and FOLLOW the service article instructions. If no service articles address this concern, INSTALL a new IPC. REFER to: Instrument Panel Cluster (IPC) 
    No  The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.
scientia non olet · About LEMON Manuals