LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2021 >> Edge ST >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Collision/Avoidance >> Parking Aid - Vehicles With: Rear Parking Aid >> Diagnosis And Testing >> Parking Aid >> Pinpoint Test(s) >> Pinpoint Test S: U0212:00 >> Pinpoint Test S: U0212:00

Pinpoint Test S: U0212:00

  1. S1 VERIFY THE CUSTOMER CONCERN

    • Ignition ON.

    • Verify there is an observable symptom present.

    Is an observable symptom present? 

    Yes  GO to  S2
    No  Clear the DTC. The system is operating normally at this time. The DTC may have been set due to high network traffic or an intermittent fault condition.

  2. S2 CHECK THE COMMUNICATION NETWORK

    • Using a diagnostic scan tool, perform the network test.

    Do the SCCM and the GWM pass the network test? 

    Yes  GO to  S3
    No  REFER to: Controller Area Network (CAN) Module Communications Network

  3. S3 PERFORM THE SCCM (STEERING COLUMN CONTROL MODULE) SELF-TEST

    • Using a diagnostic scan tool, perform the SCCM self-test.

    Are any Diagnostic Trouble Codes (DTCs) recorded? 

    Yes  REFER to: Steering Wheel and Column Electrical Components
    No  GO to  S4

  4. S4 CHECK THE GWM (GATEWAY MODULE A) DIAGNOSTIC TROUBLE CODES (DTCS)

    • Using a diagnostic scan tool, check the GWM Continuous Memory Diagnostic Trouble Codes (CMDTCs)

    Are any Diagnostic Trouble Codes (DTCs) recorded? 

    Yes  REFER to: Controller Area Network (CAN) Module Communications Network
    No  GO to  S5

  5. S5 RECHECK THE PAM (PARKING ASSIST CONTROL MODULE) DIAGNOSTIC TROUBLE CODES (DTCS)

    • Using a diagnostic scan tool, clear the Diagnostic Trouble Codes (DTCs).

    • Operate the system and test for normal operation.

    • Check the PAM Continuous Memory Diagnostic Trouble Codes (CMDTCs).

    Is DTC U0212:00 present? 

    Yes  GO to  S6
    No  The system is operating correctly at this time. The DTC may have been set due to high network traffic or an intermittent fault condition.

  6. S6 CHECK FOR DTC (DIAGNOSTIC TROUBLE CODE) U0212:00 SET IN OTHER MODULES

    • Using a diagnostic scan tool, clear all Diagnostic Trouble Codes (DTCs).

    • Ignition OFF.

    • Wait 10 seconds.

    • Ignition ON

    • Wait 10 seconds.

    • Using a diagnostic scan tool, retrieve the Continuous Memory Diagnostic Trouble Codes (CMDTCs) from all modules.

    Is DTC U0212:00 set in other modules? 

    Yes  GO to  S7
    No  GO to  S8

  7. S7 CHECK FOR CORRECT SCCM (STEERING COLUMN CONTROL MODULE) OPERATION

    • Ignition OFF.

    • Disconnect and inspect all SCCM and related in-line connectors.

    • Repair:

      • corrosion (install new connector or terminals - clean module pins)
      • damaged or bent pins - install new terminals/pins
      • pushed-out pins - install new pins as necessary

    • Reconnect the SCCM and related in-line connectors. Make sure they seat and latch correctly.

    • Operate the system and determine if the concern is still present.

    Is the concern still present? 

    Yes  CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW the TSB instructions. If no TSB addresses this concern, INSTALL a new SCCM. REFER to: Steering Column Control Module (SCCM)
    No  The system is operating correctly at this time. Concern may have been caused by a loose or corroded connector. ADDRESS the root cause of any connector or pin issues.

  8. S8 CHECK FOR CORRECT BCM (BODY CONTROL MODULE) OPERATION

    • Ignition OFF.

    • Disconnect and inspect all BCM and related in-line connectors.

    • Repair:

      • corrosion (install new connector or terminals - clean module pins)
      • damaged or bent pins - install new terminals/pins
      • pushed-out pins - install new pins as necessary

    • Reconnect the BCM and related in-line connectors. Make sure they seat and latch correctly.

    • Operate the system and determine if the concern is still present.

    Is the concern still present? 

    Yes  CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW the TSB instructions. If no TSB addresses this concern, A guided routine is not applicable for this vehicle and market. Replace the component that was faulted through diagnosis.
    No  The system is operating correctly at this time. Concern may have been caused by a loose or corroded connector. ADDRESS the root cause of any connector or pin issues.
scientia non olet · About LEMON Manuals