Network Message Chart
Module Network Input Messages - IPC
| Broadcast Message | Originating Module | Message Purpose |
|---|---|---|
| Adaptive cruise control warning request | IPMA | Input used to display the adaptive cruise control warning messages. |
| Ambient air temperature | PCM | Filtered input used to display the outside air temperature. |
| Auto high beam indication request | IPMA | Input used to control the auto high beam RTT indicator. |
| AWD service required | AWD module/ PCM | Input used for the AWD component to control the powertrain malfunction (wrench) RTT indicator. |
| AWD status display | AWD module/ PCM | Input used to display the AWD messages. |
| Battery low state of charge | BCM | Input used to control the charging system RTT indicator, check charging system warning message and load shed messages. |
| Body service required request | BCM | Input used for the BCM controlled system faults input to control the powertrain malfunction (wrench) RTT indicator. |
| Brake fluid level low message request | BCM | Input used to display the low brake fluid level message center message. |
| Brake (red) warning indicator request | ABS module | Input used to display the message center brake system messages. Input used to display the electronic parking brake message center warning messages. |
| Camera status | IPMA | Input used to display the lane keeping system camera malfunction message. |
| Check fuel fill inlet message request | PCM | Input used to display the check fuel fill inlet message. |
| Child lock message display request | BCM | Input used to display the child lock system fault message. |
| Compass direction | APIM | Input used to display the current compass heading. |
| Cross traffic alert left status | SODL | Input used to control the blind spot information system RTT indicator and message center messages. |
| Cross traffic alert right status | SODR | Input used to control the blind spot information system RTT indicator and message center messages. |
| Cruise control set speed | PCM | Input used to indicate the cruise control set speed. Input used to control the digital speedometer displayed in the message center. |
| Cruise control status | PCM | Input used to control the cruise control RTT indicator and message display based on the system status. |
| Cruise control override | PCM | Input used to control the adaptive cruise control set speed display when the cruise control is overridden by the driver. |
| Driver door ajar status | BCM | Input used for the door ajar RTT indicator and driver door ajar warning message. Input used for the engine on warning message (push button start). Input used for the PRNDL not in park warning message. |
| EPAS failure | PSCM | Input used to control the service power steering message display. |
| Engine coolant temperature data | PCM | Input used to control the over-temperature RTT indicator and engine over-temperature warning message. |
| Engine oil life | PCM | Input used for the oil life display. |
| Engine overheat indication request | PCM | Input used to control the engine over-temperature RTT indicator and engine over-temperature warning message. |
| Engine rpm data | PCM | Input used to control the low engine oil pressure RTT indicator and low engine oil pressure warning message. Input is used to calculate the Average Fuel Economy (AFE) and DTE. |
| Engine service required request | PCM | Input used for the powertrain Electronic Throttle Control (ETC) component to control the powertrain malfunction (wrench) RTT indicator. |
| Forward collision warning message request | IPMA | Input used to display the forward collision malfunction messages. |
| Fuel flow volume display | PCM | Input used to calculate the Average Fuel Economy (AFE) and DTE. |
| Hill start assist status | ABS module | Input used to display the hill start status messages. |
| Ignition key type | BCM | Input used to calculate the Average Fuel Economy (AFE) and DTE for MyKey® settings. |
| Ignition status | BCM | Ignition RUN, START and accessory states required for the IPC operating modes and fault reporting. Input used to display the PRNDL not in park warning message. |
| Immobilizer message request | BCM | Input used to display the passive entry and push button start messages (no key detected, place key in backup slot, restart now, key programming and accessory power active). |
| Keypad code | BCM | Input used to display the factory keypad code when requested by the driver. |
| Lane keeping system status display | IPMA | Input used to control the lane keeping system off RTT indicator and the lane keeping system fault messages. |
| Lane keeping system hands off display | IPMA | Input used to display the lane keeping system keep hands off the steering wheel warning message. |
| Left rear door ajar status | BCM | Input used for the door ajar RTT indicator and the left rear door ajar warning message. |
| Liftgate ajar status | BCM | Input used for the door ajar RTT indicator and the liftgate ajar warning message. |
| Memory feedback status | DSM | Input used to display the memory set feature deny and recall messages. |
| Odometer count | PCM | Input used to display the odometer and to calculate the Average Fuel Economy (AFE) and DTE. |
| Oil pressure warning indicator status | PCM | Input used to control the engine oil pressure RTT indicator and the low engine oil pressure message center warning. |
| Parking aid front status | PAM | Input used to display the parking aid malfunction message. |
| Parking aid rear status | PAM | Input used to display the parking aid malfunction message. |
| Parking brake chime request | BCM | Input used to display the message center brake system messages. |
| Parking brake message request | ABS module | Input used to display the electronic parking brake status messages. |
| Parking brake (red) indicator request | ABS module | Input used to display the electronic parking brake status messages. |
| Passenger door ajar status | BCM | Input used for the door ajar RTT indicator and the passenger door ajar warning message. |
| Perimeter alarm chime request | BCM | Input used to display the perimeter alarm message when the vehicle is entered before deactivating the perimeter alarm. |
| Power pack status | PCM | Input used to control the engine on warning message (push button start). |
| Powertrain cooling message request | PCM | Input used to display the reduced power to cool the engine on the Gasoline Turbo Direct Injection (GTDI) engines. |
| Remote start status | BCM | Input used to control the remote start informational message display. |
| Right rear door ajar status | BCM | Input used for the door ajar RTT indicator and the right rear door ajar warning message. |
| Side obstacle detect status-left | SODL | Input used to control the blind spot information system RTT indicator and message center messages. |
| Side obstacle detect status-right | SODR | Input used to control the blind spot information system RTT indicator and message center messages. |
| Side obstacle detect sensor status-left | SODL | Input used to control the blind spot information system RTT indicator and message center messages. |
| Side obstacle detect sensor status-right | SODR | Input used to control the blind spot information system RTT indicator and message center messages. |
| Starting system fault message request | PCM | Input used to display starting system messages. |
| Stability-traction control chime request | ABS module | Input used to control the service AdvanceTrac® and traction control off warning displays. Also used to control the traction control on/off status messages. |
| Steering wheel lock message request | BCM | Input used to control the steering wheel lock system messages. |
| Steering wheel message center switch data | SCCM | Input used to control the message center navigation and functions. |
| Stop/start message request | PCM | Input used to control the auto stop/start message displays. |
| Stop/start standby indicator | PCM | Input used to control the auto stop/start RTT indicator. |
| Tire pressure system status | BCM | Input used to display specific tire training instructional messages and TPMS fault messages. |
| Trailer sway status | ABS module | Input used to display the trailer sway event in progress message. |
| Transmission gear display | PCM | Input used to display the PRNDL and gear shift position. |
| Transmission shift mode display | PCM | Input used to display the PRNDL not in park warning message Input used to display the engine on message (push button start). |
| Transmission service required | PCM | Input used for the transmission component to control the powertrain malfunction (wrench) RTT indicator. Input used for the PRNDL not in park warning message. |
| Transport mode | BCM | Input used to indicate whether the vehicle is set in factory mode or transport mode. Input used to display the PRNDL not in park warning message. Input used to display the appropriate message and power down items such as the PRNDL at key off to conserve the battery. |
| Vehicle dynamics SOS | ABS module | Input used to control the spin-out detected message. |
| Vehicle speed | PCM | Input used to display the PRNDL not in park warning message Input used to display the gear shift position. Input used to display the engine on warning message (push button start). Input used to calculate the Average Fuel Economy (AFE) and DTE. Input used to control the overspeed warning RTT indicator (Gulf Cooperative Countries [GCC]) |
Module Network Input Messages - PCM
| Broadcast Message | Originating Module | Message Purpose |
|---|---|---|
| Engine oil life data reset | IPC | Input used to reset the oil life. |