LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2021 >> Bronco Sport Base >> Repair and Diagnosis >> Engine Performance >> Fuel Delivery >> Fuel System - General Information - 1.5L ECOBOOST (132KW/180PS) - I3 (Y1) >> General Procedures >> Quick Release Coupling

Quick Release Coupling

For information on Ford Color Coded Illustrations refer to OEM COLOR CODING .

Disconnect 

NOTE: When reusing liquid or vapor tube connections, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 1 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to Fuel System Pressure Release  .
  2. Disconnect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
GFD578172Courtesy of FORD MOTOR COMPANY
GFD578173Courtesy of FORD MOTOR COMPANY

Connect 

  1. Push the quick release coupling onto the tube.
    GFD578174Courtesy of FORD MOTOR COMPANY
  2. NOTE: Make sure the retainer clip is fully seated and locked onto the tube by pulling on the quick connect coupling.

    Press the retainer clip into the quick release coupling body until flush and the tabs are locked in place.

    GFD578175Courtesy of FORD MOTOR COMPANY
  3. Connect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid or vapor tube connections, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 2 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to Fuel System Pressure Release  .
  2. Disconnect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
    GFD578176Courtesy of FORD MOTOR COMPANY
    GFD578177Courtesy of FORD MOTOR COMPANY

    Connect 

    GFD578178Courtesy of FORD MOTOR COMPANY
    GFD578179Courtesy of FORD MOTOR COMPANY
  3. Connect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid or vapor tube connections, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 3 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to Fuel System Pressure Release  .
  2. Disconnect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
    GFD578180Courtesy of FORD MOTOR COMPANY

    Connect 

    GFD578181Courtesy of FORD MOTOR COMPANY
    GFD578182Courtesy of FORD MOTOR COMPANY
  3. Connect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid or vapor tube connections, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 4 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to Fuel System Pressure Release  .
  2. Disconnect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
    GFD578183Courtesy of FORD MOTOR COMPANY
    GFD578184Courtesy of FORD MOTOR COMPANY

    Connect 

    GFD578185Courtesy of FORD MOTOR COMPANY
  3. Connect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 5 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to Fuel System Pressure Release  .
  2. Disconnect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
    GFD578186Courtesy of FORD MOTOR COMPANY
    GFD578187Courtesy of FORD MOTOR COMPANY

    Connect 

    GFD578188Courtesy of FORD MOTOR COMPANY
  3. Connect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 6 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to Fuel System Pressure Release  .
  2. Disconnect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
  3. Press the tabs of the rear retainer clip and pull it to the outward position.
GFD578189Courtesy of FORD MOTOR COMPANY
GFD578190Courtesy of FORD MOTOR COMPANY

Connect 

  1. Pull on the quick release coupling to make sure it is securely fastened.
    GFD578191Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 7 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to Fuel System Pressure Release  .
  2. Disconnect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
GFD578192Courtesy of FORD MOTOR COMPANY
GFD578193Courtesy of FORD MOTOR COMPANY

Connect 

  1. Pull on the quick connect coupling to make sure it is securely fastened.
    GFD578194Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 8 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to Fuel System Pressure Release  .
  2. Disconnect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
    GFD578186Courtesy of FORD MOTOR COMPANY
    GFD578187Courtesy of FORD MOTOR COMPANY

    Connect 

    GFD578188Courtesy of FORD MOTOR COMPANY
  3. Connect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 9 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to Fuel System Pressure Release  .
  2. Disconnect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
    1. Release the secondary locking tab.
    2. Depress the primary locking tab.
    3. Separate the quick release coupling from the tube.
GFD578195Courtesy of FORD MOTOR COMPANY

Connect 

    1. Push the quick release coupling onto the tube.
    2. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Lock the secondary locking tab.

    GFD578196Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 10 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to Fuel System Pressure Release  .
  2. Disconnect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
    1. Push on the locking tab.
    2. Lift the clip.
    GFD578197Courtesy of FORD MOTOR COMPANY
    1. Depress the tabs inward.
    2. Push the clip downward.
    3. Separate the quick release coupling from the fuel line.
GFD578198Courtesy of FORD MOTOR COMPANY

Connect 

    1. Push the quick release coupling onto the tube.
    2. Push the clip down into the quick release coupling.
    3. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

    GFD578199Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 11 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to Fuel System Pressure Release  .
  2. Disconnect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
GFD578200Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD578200Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 12 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to Fuel System Pressure Release  .
  2. Disconnect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
GFD578201Courtesy of FORD MOTOR COMPANY
GFD578202Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD578203Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 13 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to Fuel System Pressure Release  .
  2. Disconnect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
GFD578204Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD578205Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 14 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to Fuel System Pressure Release  .
  2. Disconnect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
    GFD578206Courtesy of FORD MOTOR COMPANY

    Connect 

    GFD578207Courtesy of FORD MOTOR COMPANY
  3. Connect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid or vapor tube connections, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 15 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Press both retaining tabs inward and remove quick release coupling from fuel tube.
GFD578208Courtesy of FORD MOTOR COMPANY

Connect 

  1. NOTE: Inspect and clean both quick release coupling ends.

    Install the quick release coupling onto the tube until it is fully seated.

    GFD578209Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 16 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to Fuel System Pressure Release  .
  2. Disconnect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
GFD578210Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD578210Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 17 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to Fuel System Pressure Release  .
  2. Disconnect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
GFD578211Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD578212Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 18 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to Fuel System Pressure Release  .
  2. Disconnect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
GFD578213Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD578214Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 19 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to Fuel System Pressure Release  .
  2. Disconnect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
GFD578215Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD578216Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 20 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to Fuel System Pressure Release  .
  2. Disconnect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
GFD578217Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD578218Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 21 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to Fuel System Pressure Release  .
  2. Disconnect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
GFD578219Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD578220Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 22 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to Fuel System Pressure Release  .
  2. Disconnect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
    GFD578221Courtesy of FORD MOTOR COMPANY

    Connect 

    GFD578222Courtesy of FORD MOTOR COMPANY
  3. GFD578223Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  4. NOTE: Make sure that all fuel connections are checked for leaks.
    NOTE: This step is only necessary if a new component is installed.

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

    GFD578224Courtesy of FORD MOTOR COMPANY
  5. Connect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 23 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to Fuel System Pressure Release  .
  2. Disconnect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
GFD578225Courtesy of FORD MOTOR COMPANY

Connect 

  1. NOTE: Make sure the retainer clip is fully seated and locked onto the tube by pulling on the quick connect coupling.

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

    GFD578226Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 24 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to Fuel System Pressure Release  .
  2. Disconnect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
GFD578227Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD578228Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 25 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to Fuel System Pressure Release  .
  2. Disconnect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
    1. Depress the clip into the quick release coupling.
    2. Separate the quick release coupling from the tube.
GFD578229Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD578230Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 26 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to Fuel System Pressure Release  .
  2. Disconnect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
    1. Remove the quick release coupling from the tube.
GFD578231Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD578232Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .

Disconnect 

NOTE: When reusing liquid or vapor tube connections, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 27 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to Fuel System Pressure Release  .
  2. Disconnect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
    GFD578233Courtesy of FORD MOTOR COMPANY
  3. Remove the quick release coupling from the tube.
GFD578234Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD578235Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to Battery Cables - 1.5L EcoBoost (132kW/180PS) - I3 (Y1) .
scientia non olet · About LEMON Manuals