Warnings And Messages
The message center warning messages alert the operator to possible concerns or malfunctions in the vehicle operating systems. Warning messages are generally associated with other observable outputs of the IPC (gauges, informational indicators and RTT indicators). For example, when the BCM (vacuum brake booster) or ABS module (EBB) detects a low brake fluid condition, the BCM or ABS module sends the IPC a request through the GWM to illuminate the brake warning indicator and a request to display the LOW BRAKE FLUID message in the message center. This allows the message center to be a more informative supplement to the IPC gauges and indicators.
Adaptive Cruise Control
The message center provides messages explaining the need for driver intervention and system status. The adaptive cruise control messages are supplemental to the cruise control RTT indicator and the adaptive cruise control warning chime.
AdvanceTrac
The message center provides messages to inform the driver of the AdvanceTrac system status. The messages are supplemental to the stability-traction control system indicators.
Auto Stop-Start
The message center provides additional instructions for driver intervention or warning messages when a fault in the auto stop/start system is detected.
Automatic Engine Shutdown
The message center provides multiple messages explaining the status of an impending engine idle shut down.
BLIS/ CTA
The message center provides warning messages to alert the driver the status of the BLIS or CTA system.
Brake System
The message center provides messages related to the brake system for detected brake system faults, parking brake status or faults or if the brake fluid level is low. The messages are supplemental to the brake warning indicator.
Brake Applied - Power Reduced
The message center provides a brake applied warning message to inform the driver that the brake pedal and accelerator pedals are both applied.
Change 4WD Lubrication
The message center provides the change 4WD lube to inform the driver to change the transfer case lubrication fluid.
Check Fuel Fill Inlet
The message center provides a check fuel fill inlet message to warn the driver there is a problem with the fuel fill inlet pipe resulting in a significant evaporative emission leak following vehicle refueling.
Door, Hood, Tailgate Ajar
The message center provides door, hood and tailgate ajar warnings to indicate the status of the doors, hood and tailgate.
Drive Mode
The message center provides messages to inform the driver of the status of the selected drive mode or drive mode system.
Electric Parking Brake
The message center provides messages to inform the driver of system status or instructional messages if driver intervention is required.
Electronic Lock Differential (eLocker) - Front and Rear
The message center provides informational and fault messages to inform the driver of the front or rear ELD status.
Engine Oil Life, Engine Oil Change Minder
The instrument cluster provides messages to inform the driver about the engine oil life status, engine oil life reset status and when an engine oil change is required. The duration of the interval between engine oil changes is calculated in the PCM and varies due to driving conditions. The PCM assumes a base mileage of 16, 090 km (10, 000 mi) or 1 year for normal driving. However, this number is adjusted down for conditions such as high engine temperature, high engine rpm, use of flex fuel and possibly low engine oil level. The PCM calculates and provides the engine oil life percent message to the IPC. The engine oil change minder can be reset at any time by the driver.
Engine On
The message center provides the engine on message to inform the driver the engine is still on with the driver door ajar and transmission in P.
Factory/Transport Mode
During vehicle build, some modules, such as the IPC and the BCM, are set in factory mode. While in the factory mode the IPC displays FACTORY MODE CONTACT DEALER in the message center. If the vehicle is set in factory mode, the system does not automatically exit the mode and must be manually set to either the transport or normal operation mode.
When the vehicle build is complete, the vehicle is set to transport mode. While in transport mode, the IPC displays TRANSPORT MODE CONTACT DEALER in the message center. Transport mode is used to reduce the drain on the battery during longer periods where the vehicle is not used. Various systems may be altered or are disabled when in the transport mode. The vehicle automatically reverts to normal operation mode after being driven 201 km (125 mi).
To deactivate factory mode, Refer to: Factory Mode Deactivation . To deactivate transport mode, Refer to: Transport Mode Deactivation .
Four Wheel Drive (Fault and Shifting Instructions)
The message center provides messages to check the 4x4 system, shifting instructions and to provide a system status when a fault condition exists.
Front Camera
The message center provides a message to inform the driver if a front camera malfunction is detected.
Hill Descent Control
The message center provides HDC warnings to inform the driver of the system status and when driver intervention is required.
Lane Keeping System
The message center provides a warning message for the lane keeping alert and system fault messages for the lane keeping system.
Load Shed
The message center provides load shed messages to inform the driver to use less options to conserve battery voltage.
MyKey
The IPC provides a number of MyKey® related warnings and status messages to indicate restrictions imposed on the MyKey® user. These include MyKey® active, park aid, speed limits, and buckle up warnings among others. MyKey® displays are controlled through the IPC software based on the MyKey® settings configured through the center stack display and the type of key in use (MyKey® or administrator key). The MyKey® function also uses other messages received by the IPC for other indications such as vehicle speed for speed limiter displays.
Neutral Tow
The message center provides towing system messages to indicate the status of the neutral tow feature when the neutral tow system is enabled and the vehicle is capable of free-rolling.
Parking Aid
The IPC provides messages to indicate the status of the parking aid system.
Passive Key And Immobilizer System
The message center provides the starting system fault message to indicate there is a concern with the PATS. The message center provides passive key and immobilizer system messages to indicate the key program is successful, key battery is low, key could not be programmed or failed or maximum number of keys have been programmed. The IPC uses the immobilizer message display messaged input from the BCM to display the applicable message center message.
Perimeter Alarm
The message center provides the perimeter alarm warning message to indicate the perimeter alarm has been activated and to start the vehicle to stop the alarm.
Power Child Locks, Low Key FOB Battery
The message center provides a power child lock warning to inform the driver the child lock feature did not function properly. The power child lock feature is activated through the rear window lockout switch on the driver side master window control switch.
The message center provides a message to inform the driver the key FOB battery is low and replacement is required.
Power Steering
The message center provides a message to indicate there is an EPAS system concern.
Powertrain Cooling
The message center provides a warning message to inform the driver that vehicle performance is reduced to allow the engine to cool. This feature is part of the smart cooling function in the PCM and provides powertrain cooling protection under high ambient temperature conditions.
Pre-Collision Assist
The message center provides message to inform the driver the pre-collision system is unavailable or a sensor is blocked, causing a system malfunction.
Rear Seatbelt Monitor
The message center provides a message to indicate the status of the second row seatbelts and if they are buckled.
Remote Start
The message center provides remote start messages to inform the driver the vehicle is in the remote start active state and how to change the state to a drivable state. The remote start message display is active as soon as the vehicle is remote started (the engine is running, but the ignition status is off). Once the driver places the ignition in the RUN state, the IPC carries out its startup sequence.
Seatbelt
The message center provides a message to indicate the status of the front and rear seatbelts or if there is a fault detected.
Sta-Bar Disconnect
The message center provides messages to indicate status of the stablizer bar disconnect function, instructional messages if driver intervention is required or if a system has a fault and requires service.
Stability-Traction Control On/Off
The message center provides a stability-traction control system message to indicate the status of the stability-traction control system or if the system has a fault and requires service.
Starting System
The message center provides starting system messages to inform the driver of the starting system status and when driver intervention is required in order to start the engine.
Start In Gear (4L Only)
The message center provides instructional messages of when the start in gear function is available to use when to use it. The start in gear function is only available when the 4WD Low is selected.
Steering Wheel Lock
The message center provides messages to inform the driver to turn the steering wheel to enable the release of the steering wheel lock or if a system fault condition is detected.
TPMS
The IPC provides message center displays to indicate a low tire pressure condition or a malfunction in the TPMS.
Trail 1-Pedal Drive
The message center provides messages to inform the driver of a trail 1-pedal drive system fault or instructional messages when driver intervention is required.
Trail Turn Assist
The message center provides messages to inform the driver of a trail assist system fault or instructional messages when driver intervention is required.
Transmission Not In Park
The message center provides messages to inform the driver to shift the vehicle into P. The IPC uses the operational mode based on the ignition status message and vehicle speed to determine that the vehicle is still in motion and the ignition was switched off.
Trailer Lighting
The message center provides warning messages to indicate the status of the trailer lamp connections when the vehicle is towing a trailer.
Trailer Sway
The message center provides the trailer sway warning message to inform that a trailer sway has been detected and to reduce speed to help regain control of the trailer.
Vehicle Start Inhibit (Over the Air [OTA] Update)
The message center provides a warning message that vehicle start is inhibited due to an over-the-air software update in progress.