LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2020 >> Fusion Titanium Hybrid >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 8 (Vehicle Dynamic Suspension (Except Hybrid)) >> Diagnosis And Testing >> Vehicle Dynamic Suspension >> Pinpoint Tests >> Pinpoint Test A : U3003:16

Pinpoint Test A : U3003:16

WARNING: This page is about a different variant/trim than selected.
  1. Refer to Vehicle Dynamic Suspension for schematic and connector information.

    Normal Operation and Fault Conditions 

    The VDM requires an operating voltage that is between 9 and 16 volts. The VDM receives this voltage from the BCM. The VDM has a single ground circuit. Excessive resistance or an open in one or more of these circuits, a discharged battery or a inoperative charging system results in the VDM setting a DTC.

    DTC Fault Trigger Conditions 

    DTC Description Fault Trigger Condition
    VDM U3003:16 Battery Voltage: Circuit Voltage Below Threshold This DTC sets in continuous memory and on-demand if the voltage supplied to the VDM falls below 9 volts for more than 5 seconds.

    Possible Sources 

    • Fuses
    • Wiring, terminals or connectors
    • VDM

    Visual Inspection and Pre-checks 

    • Make sure the vehicle battery terminals and cables are free of any corrosion and other contaminants.
    • Make sure the vehicle battery terminals are tightened to their correct torque specifications.
    • Make sure BCM fuse 36 (15A) is OK.

  2. NOTE: Use the correct probe adapter(s) when making measurements. Failure to use the correct probe adapter(s) may cause damage to the connector.

  3. A1 RECHECK THE VDM (VEHICLE DYNAMICS CONTROL MODULE) DIAGNOSTIC TROUBLE CODES (DTCS)

    • Using a diagnostic scan tool, clear the VDM Diagnostic Trouble Codes (DTCs).

    • Ignition OFF.

    • Ignition ON.

    • Using a diagnostic scan tool, carry out the VDM self-test.

    Is DTC U3003:16 still present? 

    Yes  GO to  A2
    No  The system is operating correctly at this time. The DTC may have set due to a previous low battery voltage condition.

  4. A2 CHECK FOR CHARGING SYSTEM DIAGNOSTIC TROUBLE CODES (DTCS) IN THE PCM (POWERTRAIN CONTROL MODULE)

    • Using a diagnostic scan tool, retrieve all Continuous Memory Diagnostic Trouble Codes (CMDTCs).

    Is DTC B1317, B1318, B1676, U3003:16 or U3003:17 present in one or more modules AND are any charging system Diagnostic Trouble Codes (DTCs) present in the PCM? 

    Yes  DIAGNOSE the vehicle charging concern. REFER to: Charging System .
    No  GO to  A3

  5. A3 CHECK THE BATTERY CONDITION AND STATE OF CHARGE

    • Carry out the Battery Condition Test. REFER to: Battery .

    Did the battery pass the condition test? 

    Yes  GO to  A4
    No  INSTALL a new battery. REFER to: Battery .

  6. A4 CHECK THE VDM (VEHICLE DYNAMICS CONTROL MODULE) VOLTAGE (SW_IGN_V_VDM) PID (PARAMETER IDENTIFICATION)

    • Ignition ON.

    • Measure and record the voltage at the battery.

    • Using a diagnostic scan tool, monitor the SW_IGN_V_VDM PID.

    Is the PID display within 0.2 volt of the recorded battery voltage? 

    Yes  GO to  A8
    No  GO to  A5

  7. A5 CHECK THE VDM (VEHICLE DYNAMICS CONTROL MODULE) VOLTAGE SUPPLY

    • Ignition OFF.

    • Disconnect VDM C3672A.

    • Ignition ON.

    • Measure:
      Positive Lead Measurement / Action Negative Lead
      C3672A-1
      GFD479024Courtesy of FORD MOTOR COMPANY
      		 Ground
      Positive Lead Measurement / Action Negative Lead
      C3672A-2
      GFD479024Courtesy of FORD MOTOR COMPANY
      		 Ground

    Is the voltage within 1 volt of the recorded battery voltage? 

    Yes  GO to  A6
    No  VERIFY BCM fuse 36 (15A) is OK. If OK, REPAIR the affected circuit for high resistance or an open. If not OK, REFER to OEM Electrical Wiring Diagram Introduction (Except Hybrid) to identify the cause of the circuit short.

  8. A6 CHECK THE VDM (VEHICLE DYNAMICS CONTROL MODULE) GROUND CIRCUIT FOR AN OPEN

    • Ignition OFF.

    • Disconnect VDM C3672A.

    • Measure:
      Positive Lead Measurement / Action Negative Lead
      C3672A-11
      GFD479023Courtesy of FORD MOTOR COMPANY
      		 Ground
      Positive Lead Measurement / Action Negative Lead
      C3672A-12
      GFD479023Courtesy of FORD MOTOR COMPANY
      		 Ground

    Is the resistance less than 3 ohms? 

    Yes  GO to  A7
    No  REPAIR the circuit.

  9. A7 VERIFY ALL WIRING CONNECTIONS

    • Ignition OFF.

    • Disconnect BCM C2280F.

    • Using a good light source, inspect all disconnected electrical connectors for the following:

      • corrosion - install new connector or terminal and clean the module pins
      • damaged or bent pins - install new terminals or pins
      • pushed-out pins - install new pins as necessary
      • spread terminals - install new terminals as necessary

    Are the connectors free of corrosion, damaged pins, bent pins, pushed-out pins and spread terminals? 

    Yes  GO to  A8
    No  REPAIR the connector or terminals. Refer to OEM Connector Repair Procedures (Except Hybrid) for schematic and connector information.

  10. A8 CHECK FOR CORRECT VDM (VEHICLE DYNAMICS CONTROL MODULE) OPERATION

    • Connect BCM C2280F. Make sure it seats and latches correctly.

    • Connect VDM C3672A and C3672B. Make sure they seat and latch correctly.

    • Operate the system and determine if the concern is still present.

    Is the concern still present? 

    Yes  CHECK OASIS for any applicable service articles: TSB, GSB, SSM or FSA. If a service article exists for this concern, DISCONTINUE this test and FOLLOW the service article instructions. If no Technical Service Bulletins (TSBs) exist for this concern, INSTALL a new VDM module. REFER to: Vehicle Dynamics Control Module (VDM) .
    No  The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector. ADDRESS the root cause of any connector or pin issues.
scientia non olet · About LEMON Manuals