DTC Chart(s)

DTC Chart: BCM

Diagnostics in this article assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods

DTC	Description	Action
B115E:01	Camera Module: General Electrical Failure	GO to Pinpoint Test A
B115E:02	Camera Module: General Signal Failure	GO to Pinpoint Test A
B115E:08	Camera Module: Bus Signal/Message Failure	GO to Pinpoint Test A
B115E:49	Camera Module: Internal Electronic Failure	GO to Pinpoint Test A
B115E:55	Camera Module: Not Configured	Sets in continuous memory and on-demand in the BCM when the rear parking aid camera is not configured. PERFORM the rear parking aid camera configuration using a diagnostic scan tool.
B115E:9A	Camera Module: Component or System Operating Conditions	Sets as an on-demand DTC in the BCM when the prerequisite conditions are not met for the on-demand self test. INSPECT the liftgate to make sure it is fully closed and DIAGNOSE any other Diagnostic Trouble Codes (DTCs) present in the BCM. REFER to:
All other Diagnostic Trouble Codes (DTCs)	-	REFER to:

DTC Chart: IPMB

Diagnostics in this article assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods

DTC	Description	Action
B115E:08	Camera Module: Bus Signal/Message Failure	For vehicles with rear only parking aid camera, GO to Pinpoint Test A For vehicles with 360 degree camera, GO to Pinpoint Test I
B115E:49	Camera Module: Internal Electronic Failure	For vehicles with rear only parking aid camera, GO to Pinpoint Test A For vehicles with 360 degree camera, GO to Pinpoint Test I
B115E:55	Camera Module: Not Configured	NOTE: A LIN circuit fault may prevent the front or rear camera from being configured properly. VERIFY the integrity of the LIN circuit wiring, terminals and connectors when diagnosing a camera configuration concern. Sets in continuous memory and on-demand in the IPMB when the rear camera is not configured.VERIFY the battery voltage and condition.PERFORM the rear camera configuration using a diagnostic scan tool under Electrical>Service Functions>LIN New Module Initialization.
B148E:08	Front Camera: Bus Signal/Message Failure	GO to Pinpoint Test J
B148E:49	Front Camera: Internal Electronic Failure	GO to Pinpoint Test J
B148E:55	Front Camera: Not Configured	NOTE: A LIN circuit fault may prevent the front or rear camera from being configured properly. VERIFY the integrity of the LIN circuit wiring, terminals and connectors when diagnosing a camera configuration concern. Sets in continuous memory and on-demand in the IPMB when the front camera is not configured.VERIFY the battery voltage and condition.PERFORM the front camera configuration using a diagnostic scan tool under Electrical>Service Functions>LIN New Module Initialization.
B14A4:11	Camera Power: Circuit Short To Ground	GO to Pinpoint Test K
B14A5:11	Multi-Camera View Switch: Circuit Short To Ground	GO to Pinpoint Test L
B1530:78	Trailer Aid Camera Angle Detection: Alignment or Adjustment Incorrect	REFER to: Parking Aid See DTC Chart: IPMB
C1001:78	Vision System Camera: Alignment or Adjustment Incorrect	Sets in continuous memory and on-demand in the IPMB when the 360 degree view camera alignment has not been successfully completed. PERFORM the 360 degree view camera alignment using a diagnostic scan tool. REFER to: 360 Degree View Camera Alignment
U0121:87	Lost Communication With Anti-Lock Brake System (ABS) Control Module: Missing Message	GO to Pinpoint Test P
U0159:87	Lost Communication With Parking Assist Control Module "A": Missing Message	GO to Pinpoint Test Q
U0253:87	Lost Communication With Accessory Protocol Interface Module: Missing Message	GO to Pinpoint Test R
U0415:00	Invalid Data Received From Anti-Lock Brake System (ABS) Control Module: No Sub Type Information	RETRIEVE and FOLLOW non-network Diagnostic Trouble Codes (DTCs) from the ABS module. REFER to: Anti-Lock Brake System (ABS) and Stability Control . If no Diagnostic Trouble Codes (DTCs) are present in the ABS module, DIAGNOSE the observable symptom.
U045A:00	Invalid Data Received From Parking Assist Control Module "A": No Sub Type Information	RETRIEVE and FOLLOW non-network Diagnostic Trouble Codes (DTCs) from the PAM. REFER to: Parking Aid If no Diagnostic Trouble Codes (DTCs) are present in the PAM, DIAGNOSE the observable symptom.
U0554:00	Invalid Data Received From Accessory Protocol Interface Module: No Sub Type Information	RETRIEVE and FOLLOW non-network Diagnostic Trouble Codes (DTCs) from the APIM. REFER to: Information and Entertainment System If no Diagnostic Trouble Codes (DTCs) are present in the APIM, DIAGNOSE the observable symptom.
U1000:11	Solid State Driver Protection Active - Driver Disabled: Circuit Short To Ground	The IPMB has temporarily disabled the LH and RH side parking aid camera voltage supply output due to a repetitive excessive current draw. RETRIEVE and REPAIR all other IPMB Diagnostic Trouble Codes (DTC). REPEAT the IPMB self-test. If DTC U1000:11 is still present after all other Diagnostic Trouble Codes (DTCs) have been addressed, INSTALL a new IPMB. REFER to: Image Processing Module B (IPMB)
U201A:55	Control Module Main Calibration Data: Not Configured	VERIFY the battery voltage and condition. CHECK the vehicle service history for recent service actions related to this module. This DTC can set due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, INSTALL As-Built data from Professional Technician Society (PTS), following the diagnostic scan tool instructions under Module Programming>As-Built. REFER to: Module Configuration - System Operation and Component Description If there have not been recent service actions with this module, INSTALL a new IPMB to correct the failure to retain configuration data. REFER to: Image Processing Module B (IPMB)
U2100:00	Initial Configuration Not Complete: No Sub Type Information	VERIFY the battery voltage and condition. CHECK the vehicle service history for recent service actions related to this module. This DTC can set due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, INSTALL As-Built data from Professional Technician Society (PTS), following the diagnostic scan tool instructions under Module Programming>As-Built. REFER to: Module Configuration - System Operation and Component Description If there have not been recent service actions with this module, INSTALL a new IPMB to correct the failure to retain configuration data. REFER to: Image Processing Module B (IPMB)
U3000:42	Control Module: General Memory Failure	RETRIEVE and REPAIR all other IPMB Diagnostic Trouble Codes (DTCS) and REPEAT the IPMB self-test. If DTC U3000:42 is still present after all other Diagnostic Trouble Codes (DTCs) have been repaired, INSTALL a new IPMB. REFER to: Image Processing Module B (IPMB)
U3000:49	Control Module: Internal Electronic Failure	The IPMB has permanently disabled the LH and RH side parking aid camera voltage supply output because an excessive current draw has occurred more times than the module can withstand. RETRIEVE and REPAIR all other IPMB Diagnostic Trouble Codes (DTC). REPEAT the IPMB self-test. If DTC U3000:49 is still present after all other Diagnostic Trouble Codes (DTCs) have been addressed, INSTALL a new IPMB. REFER to: Image Processing Module B (IPMB)

DTC Chart: APIM

Diagnostics in this article assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods

DTC	Description	Action
C1001:01	Vision System Camera: General Electrical Failure	If the vehicle is equipped with a rear only parking aid camera, GO to Pinpoint Test A If the vehicle is equipped with a 360 degree view camera, GO to Pinpoint Test G
All other Diagnostic Trouble Codes (DTCs)	--	REFER to: Information and Entertainment System