Pinpoint Test L : B007F:11, B007F:12, B007F:13, B007F:1A

Refer to SUPPLEMENTAL RESTRAINT SYSTEM for schematic and connector information.

Normal Operation and Fault Conditions

The RCM continuously monitors the passenger seatbelt retractor pretensioner circuits for the following faults:

Resistance out of range
Unexpected voltage
Short to ground
Faulted passenger seatbelt retractor pretensioner

If a fault is detected, the RCM stores DTC B007F:11, B007F:12, B007F:13 or B007F:1A in memory and sends a message to the IPC to illuminate the airbag warning indicator.

The RCM analyzes the deployment loop resistance to determine if a fault exists. The value displayed in the PID is the deployment loop resistance measured by the RCM. If the value displayed is lower or higher than the desired range (refer to diagram below), the RCM can set a DTC. As the deployment loop resistance drifts farther outside the desired range, the chance for a DTC increases. Small variations in resistance can occur due to the effect of road vibrations on terminal fit. Crimps and terminals can be affected by stress and harness movement and can cause an increase in resistance due to wire strain. These variables can result in an intermittent fault. For this reason, the test requires the PID value to be within the desired range before the fault is considered repaired, regardless if the module is reporting an on-demand DTC at the time of diagnosis. Following this direction helps make sure that minor changes in resistance do not create a repeat concern. This test uses process of elimination to diagnose each part of the deployment loop circuit including:

Wiring
Connections
Passenger seatbelt retractor pretensioner
RCM

Courtesy of FORD MOTOR COMPANY

1 - May set DTC
2 - Desired range

DTC Fault Trigger Conditions

DTC	Description	Fault Trigger Condition
RCM B007F:11	Passenger Seatbelt Pretensioner "C" Deployment Control: Circuit Short To Ground	A fault is indicated when the RCM senses a short to ground on either passenger seatbelt retractor pretensioner circuit for approximately 6 seconds.
RCM B007F:12	Passenger Seatbelt Pretensioner "C" Deployment Control: Circuit Short To Battery	A fault is indicated when the RCM senses a short to voltage on either passenger seatbelt retractor pretensioner circuit for approximately 6 seconds.
RCM B007F:13	Passenger Seatbelt Pretensioner "C" Deployment Control: Circuit Open	A fault is indicated when the RCM measures more than the desired resistance range between passenger seatbelt retractor pretensioner circuits for approximately 6 seconds.
RCM B007F:1A	Passenger Seatbelt Pretensioner "C" Deployment Control: Circuit Resistance Below Threshold	A fault is indicated when the RCM measures less than the desired resistance range between passenger seatbelt retractor pretensioner circuits for approximately 6 seconds.

Possible Sources

Wiring, terminals or connectors
Passenger seatbelt retractor pretensioner
RCM

WARNING: Incorrect repair techniques or actions can cause an accidental Supplemental Restraint System (SRS) deployment. Never compromise or depart from these instructions. Failure to precisely follow all instructions could result in serious personal injury from an accidental deployment.
NOTE: Use the correct probe adapter(s) when making measurements. Failure to use the correct probe adapter(s) may cause damage to the connector.
NOTE: Most faults are due to connector and/or wiring concerns. Carry out a thorough inspection and verification before proceeding with the pinpoint test.
NOTE: Only disconnect or reconnect SRS components when instructed to do so within a pinpoint test step. Failure to follow this instruction may result in incorrect diagnosis of the SRS.
NOTE: Install new components only when directed to do so in the pinpoint test.
NOTE: Always make sure the correct SRS component is being installed. Parts released for other vehicles may not be compatible even if they appear physically similar. Check the part number listed in the Ford parts catalog to make sure the correct component is being installed. If an incorrect SRS component is installed, Diagnostic Trouble Codes (DTCs) may set.
NOTE: The SRS must be fully operational and free of faults before releasing the vehicle to the customer.

L1 RETRIEVE RCM (RESTRAINTS CONTROL MODULE) DIAGNOSTIC TROUBLE CODES (DTCS)

WARNING: Before beginning any service procedure in this information, refer to Safety Warnings in General Information. Failure to follow this instruction may result in serious personal injury.

REFER to: Pyrotechnic Device Health and Safety Precautions .

Ignition ON.

Using a diagnostic scan tool, perform RCM self-test.

Was DTC B007F:11, B007F:12, B007F:13 or B007F:1A retrieved on-demand during self-test?

Yes	This fault cannot be cleared until it is corrected and the DTC is no longer retrieved on-demand during self-test. For DTC B007F:13 or B007F:1A, GO to L2 For DTC B007F:11, GO to L8 For DTC B007F:12, GO to L10

No	This is an intermittent fault when present as a CMDTC only. For DTC B007F:13 or B007F:1A, GO to L13 For DTC B007F:11, GO to L14 For DTC B007F:12, GO to L15

L2 CHECK THE PASSENGER SEATBELT RETRACTOR PRETENSIONER DEPLOYMENT CONTROL (DEPLOY_24_R) PID (PARAMETER IDENTIFICATION)
- Access the RCM and monitor the DEPLOY_24_R (mOhm) PID
- Monitor and record the resistance value displayed by the PID.
Does the PID value read between 1.7 and 2.98 ohms?

Yes GO to L12

No GO to L3

L3 CHECK THE PASSENGER SEATBELT RETRACTOR PRETENSIONER DEPLOYMENT CONTROL (DEPLOY_24_R) PID (PARAMETER IDENTIFICATION) WHILE CARRYING OUT THE HARNESS TEST

Access the RCM and monitor the DEPLOY_24_R (mOhm) PID

While monitoring the PID, carry out the harness test of the passenger seatbelt retractor pretensioner circuits and accessible connectors (including any inline connectors) by wiggling and flexing the wire harness and connectors frequently. Record the resistance value indicated by the PID.

Does the PID value read between 1.7 and 2.98 ohms while carrying out the harness test?

Yes	DEPOWER the SRS and REPAIR the connector, terminals or wire harness as needed. REFER to: Supplemental Restraint System (SRS) Depowering . Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information. GO to L17

No	For PID value less than 1.7 ohms, GO to L4 For PID value greater than 2.98 ohms, GO to L6

L4 CHECK THE PASSENGER SEATBELT RETRACTOR PRETENSIONER DEPLOYMENT CONTROL DTC (DIAGNOSTIC TROUBLE CODE) FOR A FAULT STATUS CHANGE (LOW RESISTANCE INDICATED)

NOTE: This pinpoint test step attempts to change the fault reported by the RCM by inducing a different fault condition. If the reported fault changes, this indicates the RCM is functioning correctly and is not the source of the fault.
- Ignition OFF.
- Depower the SRS. REFER to: Supplemental Restraint System (SRS) Depowering .
- Disconnect Passenger Seatbelt Retractor Pretensioner C303A.
- Repower the SRS.
  Do not prove out the SRS at this time. REFER to:Supplemental Restraint System (SRS) Repowering .
- Ignition ON.
- Using a diagnostic scan tool, perform RCM self-test.
- DIAGNOSTIC TIP: When viewing Diagnostic Trouble Codes (DTCs) with the passenger seatbelt retractor pretensioner disconnected, an open circuit fault is normally retrieved.
Did the on-demand DTC change from B007F:1A to B007F:13?

Yes GO to L11

No GO to L5

L5 CHECK FOR A SHORT BETWEEN PASSENGER SEATBELT RETRACTOR PRETENSIONER CIRCUITS

Ignition OFF.

Depower the SRS. REFER to: Supplemental Restraint System (SRS) Depowering .

Disconnect RCM C310A and C310B.

Measure:

Positive Lead	Measurement / Action	Negative Lead
C303A-1	Courtesy of FORD MOTOR COMPANY	C303A-2

Is the resistance greater than 10, 000 ohms?

Yes

GO to L12

No	REPAIR the circuits. Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information. GO to L17

L6 CHECK THE PASSENGER SEATBELT RETRACTOR PRETENSIONER CIRCUITS FOR AN OPEN

Ignition OFF.

Depower the SRS. REFER to: Supplemental Restraint System (SRS) Depowering .

Disconnect Passenger Seatbelt Retractor Pretensioner C303A.

Disconnect RCM C310A and C310B.

Measure:

Positive Lead	Measurement / Action	Negative Lead
C310B-9	Courtesy of FORD MOTOR COMPANY	C303A-1
C310B-10	Courtesy of FORD MOTOR COMPANY	C303A-2

Are the resistances less than 0.5 ohm?

Yes

GO to L7

No	REPAIR the circuit(s). Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information. GO to L17

L7 CHECK THE PASSENGER SEATBELT RETRACTOR PRETENSIONER DEPLOYMENT CONTROL DTC (DIAGNOSTIC TROUBLE CODE) FOR A FAULT STATUS CHANGE (OPEN INDICATED)

NOTE: This pinpoint test step attempts to change the fault reported by the RCM by inducing a different fault condition. If the reported fault changes, this indicates the RCM is functioning correctly and is not the source of the fault.

Connect RCM C310A and C310B.

Connect a fused jumper wire:

Lead 1	Measurement / Action	Lead 2
C303A-1	Courtesy of FORD MOTOR COMPANY	C303A-2

Repower the SRS.
Do not prove out the SRS at this time. REFER to:Supplemental Restraint System (SRS) Repowering .

Ignition ON.

Using a diagnostic scan tool, perform RCM self-test.

DIAGNOSTIC TIP: When viewing Diagnostic Trouble Codes (DTCs) with the passenger seatbelt retractor pretensioner circuits shorted together, a low resistance fault is normally retrieved.

Did the on-demand DTC change from B007F:13 to B007F:1A?

Yes	REMOVE the fused jumper wire and GO to L11

No	REMOVE the fused jumper wire and GO to L12

L8 CHECK THE PASSENGER SEATBELT RETRACTOR PRETENSIONER DEPLOYMENT CONTROL DTC (DIAGNOSTIC TROUBLE CODE) FOR A FAULT STATUS CHANGE (SHORT TO GROUND INDICATED)

NOTE: This pinpoint test step attempts to change the fault reported by the RCM by inducing a different fault condition. If the reported fault changes, this indicates the RCM is functioning correctly and is not the source of the fault.
- Ignition OFF.
- Depower the SRS. REFER to: Supplemental Restraint System (SRS) Depowering .
- Disconnect Passenger Seatbelt Retractor Pretensioner C303A.
- Repower the SRS.
  Do not prove out the SRS at this time. REFER to:Supplemental Restraint System (SRS) Repowering .
- Ignition ON.
- Using a diagnostic scan tool, perform RCM self-test.
- DIAGNOSTIC TIP: When viewing Diagnostic Trouble Codes (DTCs) with the passenger seatbelt retractor pretensioner disconnected, an open circuit fault is normally retrieved.
Did the on-demand DTC change from B007F:11 to B007F:13?

Yes GO to L11

No GO to L9

L9 CHECK THE PASSENGER SEATBELT RETRACTOR PRETENSIONER CIRCUITS FOR A SHORT TO GROUND

Ignition OFF.

Depower the SRS. REFER to: Supplemental Restraint System (SRS) Depowering .

Disconnect RCM C310A and C310B.

Measure:

Positive Lead	Measurement / Action	Negative Lead
C303A-1	Courtesy of FORD MOTOR COMPANY	Ground
C303A-2	Courtesy of FORD MOTOR COMPANY	Ground

Are the resistances greater than 10, 000 ohms?

Yes

GO to L12

No	REPAIR the circuit(s). Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information. GO to L17

L10 CHECK THE PASSENGER SEATBELT RETRACTOR PRETENSIONER CIRCUITS FOR A SHORT TO VOLTAGE

Ignition OFF.

Depower the SRS. REFER to: Supplemental Restraint System (SRS) Depowering .

Disconnect Passenger Seatbelt Retractor Pretensioner C303A.

Disconnect RCM C310A and C310B.

Repower the SRS.
Do not prove out the SRS at this time. REFER to:Supplemental Restraint System (SRS) Repowering .

Ignition ON.

Measure:

Positive Lead	Measurement / Action	Negative Lead
C303A-1	Courtesy of FORD MOTOR COMPANY	Ground
C303A-2	Courtesy of FORD MOTOR COMPANY	Ground

Is any voltage present?

Yes	REPAIR the circuit(s). Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information. GO to L17

GO to L12

L11 CONFIRM THE PASSENGER SEATBELT RETRACTOR PRETENSIONER FAULT

NOTE: Make sure all SRS components and the RCM electrical connectors are connected before carrying out the self-test. If not, Diagnostic Trouble Codes (DTCs) will be recorded.

Ignition OFF.

Depower the SRS. REFER to: Supplemental Restraint System (SRS) Depowering .

Prior to reconnecting any previously disconnected SRS component:
- inspect connector(s) (including any inline connectors) for pushed-out, loose or spread terminals and loose or frayed wire connections at terminals.
- inspect wire harness for any damaged, pinched, cut or pierced wires.
- inspect RCM C310A and C310B Connector Position Assurance (CPA) lever/lock for correct operation.
- repair any concerns found. Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information.

Connect Passenger Seatbelt Retractor Pretensioner C303A.

Repower the SRS.
Do not prove out the SRS at this time. REFER to:Supplemental Restraint System (SRS) Repowering .

Ignition ON.

Using a diagnostic scan tool, perform RCM self-test.

Was the original DTC retrieved on-demand during self-test?

Yes	INSTALL a new passenger seatbelt retractor. REFER to: Front Seatbelt Retractor and Pretensioner . GO to L17

In the process of diagnosing the fault, the fault condition has become intermittent. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test. For DTC B007F:13 or B007F:1A, GO to L13 For DTC B007F:11, GO to L14 For DTC B007F:12, GO to L15

L12 CONFIRM THE RCM (RESTRAINTS CONTROL MODULE) FAULT

NOTE: Make sure all SRS components and the RCM electrical connectors are connected before carrying out the self-test. If not, Diagnostic Trouble Codes (DTCs) will be recorded.

Ignition OFF.

Depower the SRS. REFER to: Supplemental Restraint System (SRS) Depowering .

Prior to reconnecting any previously disconnected SRS component:
- inspect connector(s) (including any inline connectors) for pushed-out, loose or spread terminals and loose or frayed wire connections at terminals.
- inspect wire harness for any damaged, pinched, cut or pierced wires.
- inspect RCM C310A and C310B Connector Position Assurance (CPA) lever/lock for correct operation.
- repair any concerns found. Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information.

Connect Passenger Seatbelt Retractor Pretensioner C303A.

Connect RCM C310A and C310B.

Repower the SRS.
Do not prove out the SRS at this time. REFER to:Supplemental Restraint System (SRS) Repowering .

Ignition ON.

Using a diagnostic scan tool, perform RCM self-test.

Was the original DTC retrieved on-demand during self-test?

Yes

CHECK OASIS for any applicable service articles: TSB, GSB, SSM or FSA. If a service article exists for this concern, DISCONTINUE this test and FOLLOW the service article instructions. If no service articles address this concern, INSTALL a new RCM. REFER to: Restraints Control Module (RCM) . GO to L17

L13 CHECK THE PASSENGER SEATBELT RETRACTOR PRETENSIONER DEPLOYMENT CONTROL (DEPLOY_24_R) PID (PARAMETER IDENTIFICATION) FOR AN INTERMITTENT LOW RESISTANCE OR OPEN CIRCUIT FAULT

Access the RCM and monitor the DEPLOY_24_R (mOhm) PID

While monitoring the PID, attempt to recreate the fault by wiggling connectors (including any inline connectors) and flexing the wire harness frequently. Record the resistance value indicated by the PID.

Does the PID value read between 1.7 and 2.98 ohms?

Yes	The fault is not present and cannot be recreated at this time. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test. GO to L16

No	DEPOWER the SRS and REPAIR as necessary. REFER to: Supplemental Restraint System (SRS) Depowering . Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information. GO to L17

L14 CHECK THE PASSENGER SEATBELT RETRACTOR PRETENSIONER DEPLOYMENT CONTROL CIRCUITS FOR AN INTERMITTENT SHORT TO GROUND FAULT

Attempt to recreate the fault by wiggling connectors (including any inline connectors) and flexing the wire harness frequently.

Using a diagnostic scan tool, perform RCM self-test.

Was DTC B007F:11 retrieved on-demand during self-test?

Yes	DEPOWER the SRS and REPAIR as necessary. REFER to: Supplemental Restraint System (SRS) Depowering . Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information. GO to L17

No	The fault is not present and cannot be recreated at this time. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test. GO to L16

L15 CHECK THE PASSENGER SEATBELT RETRACTOR PRETENSIONER DEPLOYMENT CONTROL CIRCUITS FOR AN INTERMITTENT SHORT TO VOLTAGE FAULT

Ignition OFF.

Depower the SRS. REFER to: Supplemental Restraint System (SRS) Depowering .

Disconnect Passenger Seatbelt Retractor Pretensioner C303A.

Repower the SRS.
Do not prove out the SRS at this time. REFER to:Supplemental Restraint System (SRS) Repowering .

Ignition ON.

Attempt to recreate the fault by wiggling connectors (including any inline connectors) and flexing the wire harness frequently.

Using a diagnostic scan tool, perform RCM self-test.

Was DTC B007F:12 retrieved on-demand during self-test?

Yes	DEPOWER the SRS and REPAIR as necessary. REFER to: Supplemental Restraint System (SRS) Depowering . Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information. GO to L17

No	The fault is not present and cannot be recreated at this time. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test. GO to L16

L16 CHECK THE HARNESS AND CONNECTORS

Ignition OFF.

Depower the SRS. REFER to: Supplemental Restraint System (SRS) Depowering .

Connect Passenger Seatbelt Retractor Pretensioner C303A.
- Inspect connector(s) (including any inline connectors) for corrosion, loose or spread terminals and loose or frayed wire connections at terminals.
- Inspect wire harness for any damage, pinched, cut or pierced wires.
- Inspect RCM C310A and C310B Connector Position Assurance (CPA) lever/lock for correct operation.

Were any concerns found?

Yes	REPAIR as necessary. Refer to OEM CONNECTOR REPAIR PROCEDURES for schematic and connector information. GO to L17

No	The fault is not present and cannot be recreated at this time. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test. GO to L17

L17 CHECK FOR ADDITIONAL SRS (SUPPLEMENTAL RESTRAINT SYSTEM) DIAGNOSTIC TROUBLE CODES (DTCS)

WARNING: Turn the ignition OFF and wait one minute to deplete the backup power supply. Failure to follow this instruction may result in serious personal injury or death in the event of an accidental deployment.

Ignition OFF.

Connect all previously disconnected SRS components.

If previously directed to depower the SRS, repower the SRS.
Do not prove out the SRS at this time. REFER to:Supplemental Restraint System (SRS) Repowering .

Ignition ON.

NOTE: When selecting Restraints from the Self Test menu, DTCs are retrieved from the RCM, OCSM and BECMB.

Using a diagnostic scan tool, perform

Restraints self-test.

Are any RCM and/or OCSM Diagnostic Trouble Codes (DTCs) retrieved on-demand during self-test?

Yes	Do not clear any Diagnostic Trouble Codes (DTCs) until all Diagnostic Trouble Codes (DTCs) have been resolved. DIAGNOSE and REPAIR the RCM and/or OCSM Diagnostic Trouble Codes (DTCs). REFER to RCM (DTC) Chart .

No	The repair is complete. RETURN the vehicle to the customer.