LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2020 >> Edge SE, FWD >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Drivers Assistance Systems - ADAS >> Parking Aid - Vehicles With: Parking Aid Camera >> Diagnosis And Testing >> Parking Aid >> DTC Chart(s) >> DTC Chart: IPMB

DTC Chart: IPMB

Diagnostics in this article assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .

DTC Description Action
B115E:08 Camera Module: Bus Signal/Message Failure GO to Pinpoint Test I 
B115E:49 Camera Module: Internal Electronic Failure Sets in continuous memory and on-demand in the IPMB when an internal fault is detected in the rear parking aid camera.
CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the IPMB self-test.
If DTC B115E:49 returns, INSTALL a new rear parking aid camera. REFER to: Rear Parking Aid Camera  .
B115E:55 Camera Module: Not Configured
NOTE: A LIN circuit fault may prevent the front or rear camera from being configured properly. VERIFY the integrity of the LIN circuit wiring, terminals and connectors when diagnosing a camera configuration concern.
Sets in continuous memory and on-demand in the IPMB when the rear parking aid camera is not configured.PERFORM the rear parking aid camera configuration using a diagnostic scan tool under Electrical>Service Functions>LIN New Module Initialization.
B148E:08 Front Camera: Bus Signal/Message Failure GO to Pinpoint Test J 
B148E:49 Front Camera: Internal Electronic Failure Sets in continuous memory and on-demand in the IPMB when an internal fault is detected in the front parking aid camera.
CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the IPMB self-test.
If DTC B148E:49 returns, INSTALL a new front parking aid camera. REFER to: Front Parking Aid Camera  .
B148E:55 Front Camera: Not Configured
NOTE: A LIN circuit fault may prevent the front or rear camera from being configured properly. VERIFY the integrity of the LIN circuit wiring, terminals and connectors when diagnosing a camera configuration concern.
Sets in continuous memory and on-demand in the IPMB when the front parking aid camera is not configured.PERFORM the front camera configuration using a diagnostic scan tool under Electrical>Service Functions>LIN New Module Initialization.
U0121:87 Lost Communication With Anti-Lock Brake System (ABS) Control Module: Missing Message GO to Pinpoint Test O 
U0159:87 Lost Communication With Parking Assist Control Module "A": Missing Message GO to Pinpoint Test P 
U0253:87 Lost Communication With Accessory Protocol Interface Module: Missing Message GO to Pinpoint Test Q 
U0415:00 Invalid Data Received From Anti-Lock Brake System (ABS) Control Module: No Sub Type Information RETRIEVE and FOLLOW non-network Diagnostic Trouble Codes (DTCs) from the ABS module. REFER to: Anti-Lock Brake System (ABS) and Stability Control .
If no Diagnostic Trouble Codes (DTCs) are present in the ABS module, DIAGNOSE the observable symptom.
U045A:00 Invalid Data Received From Parking Assist Control Module "A": No Sub Type Information RETRIEVE and FOLLOW non-network Diagnostic Trouble Codes (DTCs) from the PAM. REFER to: Parking Aid .
If no Diagnostic Trouble Codes (DTCs) are present in the PAM, DIAGNOSE the observable symptom.
U0554:00 Invalid Data Received From Accessory Protocol Interface Module: No Sub Type Information RETRIEVE and FOLLOW non-network Diagnostic Trouble Codes (DTCs) from the APIM. REFER to: Information and Entertainment System .
If no Diagnostic Trouble Codes (DTCs) are present in the APIM, DIAGNOSE the observable symptom.
U201A:55 Control Module Main Calibration Data: Not Configured CHECK the vehicle service history for recent service actions related to this module. This DTC can set due to incomplete or incorrect PMI procedures.
If there have been recent service actions with this module, INSTALL As-Built data from Professional Technician Society (PTS), following the diagnostic scan tool instructions under Module Programming>As-Built. REFER to: Module Configuration - System Operation and Component Description .
If there have not been recent service actions with this module, INSTALL a new IPMB to correct the failure to retain configuration data. REFER to: Image Processing Module B (IPMB)  .
U2100:00 Initial Configuration Not Complete: No Sub Type Information CHECK the vehicle service history for recent service actions related to this module. This DTC can set due to incomplete or incorrect PMI procedures.
If there have been recent service actions with this module, INSTALL As-Built data from Professional Technician Society (PTS), following the diagnostic scan tool instructions under Module Programming>As-Built. REFER to: Module Configuration - System Operation and Component Description .
If there have not been recent service actions with this module, INSTALL a new IPMB to correct the failure to retain configuration data. REFER to: Image Processing Module B (IPMB)  .
U3000:42 Control Module: General Memory Failure RETRIEVE and REPAIR all other IPMB Diagnostic Trouble Codes (DTCS) and REPEAT the IPMB self-test.
If DTC U3000:42 is still present after all other Diagnostic Trouble Codes (DTCs) have been repaired, INSTALL a new IPMB. REFER to: Image Processing Module B (IPMB)  .
scientia non olet · About LEMON Manuals