Pinpoint Test Bx : U0154:00

BX1 VERIFY THE CUSTOMER CONCERN

Ignition ON.

Verify there is an observable symptom present.

Is an observable symptom present?

Yes

GO to BX2

No	The system is operating normally at this time. The DTC may have been set due to high network traffic or an intermittent fault condition.

BX2 CHECK THE COMMUNICATION NETWORK
- Using a diagnostic scan tool, perform the network test.
Does the OCSM pass the network test?

Yes GO to BX3

No REFER to: Communications Network .

BX3 PERFORM THE IPC (INSTRUMENT PANEL CLUSTER) SELF-TEST
- Using a diagnostic scan tool, perform the IPC self-test.
Are any non-network Diagnostic Trouble Codes (DTCs) present?

Yes DIAGNOSE all non-network Diagnostic Trouble Codes (DTCs). REFER to DTC Chart: Instrument Panel Cluster (IPC) .

No GO to BX4

BX4 CHECK THE GWM (GATEWAY MODULE A) DIAGNOSTIC TROUBLE CODES (DTCS)
- Using a diagnostic scan tool, check the GWM Continuous Memory Diagnostic Trouble Codes (DTCs).
Are any Diagnostic Trouble Codes (DTCs) recorded?

Yes REFER to: Communications Network .

No GO to BX5

BX5 PERFORM THE OCSM (OCCUPANT CLASSIFICATION SYSTEM MODULE) SELF-TEST
- Using a diagnostic scan tool, perform the OCSM self-test.
Are any non-network Diagnostic Trouble Codes (DTCs) present?

Yes REFER to: Airbag Supplemental Restraint System (SRS) .

No GO to BX6

BX6 RECHECK THE IPC (INSTRUMENT PANEL CLUSTER) DIAGNOSTIC TROUBLE CODES (DTCS)

Using a diagnostic scan tool, clear the IPC Diagnostic Trouble Codes (DTCs).

Ignition OFF.

Ignition ON.

Wait 10 seconds.

Using a diagnostic scan tool, perform the continuous memory self-test.

Check the IPC Diagnostic Trouble Codes (DTCs).

Is DTC U0154:00 still present?

Yes

GO to BX7

No	The system is operating correctly at this time. The DTC may have been set due to high network traffic or an intermittent fault condition.

BX7 CHECK FOR OTHER CAUSES OF COMMUNICATION NETWORK CONCERN

NOTE: If new modules were installed prior to the DTC being set, the module configuration may be incorrectly set during the PMI, or the PMI may not have been carried out.

CHECK the vehicle service history for recent service actions related to the OCSM, GWM or IPC. If recent service history is found:
- verify correct replacement module was installed
  - HVBOM may be used to verify correct part fitment
- verify the configuration of replacement module was correct
  - re-configure module using as-built data if prior configuration is suspect
- verify the module was not obtained from a like vehicle and installed into customer vehicle
  - return the swapped module to source vehicle and obtain new replacement module

Operate the system and determine if the observable symptom is still present.

Is the observable symptom still present?

Yes

GO to BX8

No	The system is operating correctly at this time. The concern may have been due to incorrect parts replacement procedures or incorrect module configuration.

BX8 CHECK FOR CORRECT OCSM (OCCUPANT CLASSIFICATION SYSTEM MODULE) OPERATION

Ignition OFF.

Disconnect and inspect the OCS sensor and all related in-line connectors.

Repair:
- corrosion (install new connector or terminals - clean module pins)
- damaged or bent pins - install new terminals/pins
- pushed-out pins - install new pins as necessary

Reconnect the OCS sensor and all related in-line connectors. Make sure they seat and latch correctly.

Operate the system and determine if the concern is still present.

Is the concern still present?

Yes	CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no Technical Service Bulletins (TSBs) address this concern, INSTALL a new OCS sensor. REFER to: Occupant Classification System (OCS) Sensor .

No	The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.