LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2018 >> Taurus Limited, FWD, Gas >> Repair and Diagnosis >> External Pages >> Different car >> Section 51 (Automatic Transmission - 6-Speed Automatic Transmission - 6F15 (2 Of 2)) >> Diagnosis And Testing >> Intermediate Clutch Assembly

Intermediate Clutch Assembly

WARNING: This page is about a different car, the 2018 Ford EcoSport. However, it is still accessible from the selected car via links, so may be relevant.

Intermediate Clutch 

For intermediate (2, 6) clutch operation, REFER to: Transmission Description . REFER to: Intermediate Clutch Assembly .

Intermediate Clutch 

Condition Possible Sources Action
Intermediate (2, 6) clutch does not apply SSC solenoid filter blocked CLEAN or INSTALL a new solenoid. REFER to: Solenoid .
SSC is mechanically stuck OFF INSTALL a new solenoid. REFER to: Solenoid .
Intermediate (2, 6) clutch regulator valve stuck OFF DISASSEMBLE, CLEAN and INSPECT the intermediate (2, 6) clutch regulator valve. If bore or valve is damaged, INSTALL a new main control valve body. REFER to: Main Control Valve Body .
SSC VBS CB26, CB26 hydraulic circuits blocked or leaking DISASSEMBLE and INSPECT the main control valve body and separator plate passages for debris/blockage. CLEAN as necessary. REFER to: Main Control Valve Body .
CB26 hydraulic circuit blocked or leaking DISASSEMBLE and INSPECT the transmission case passages for debris/blockage. CLEAN as necessary.
Rear planetary sun gear and shell assembly INSPECT the sun gear and shell for wear and damage. INSTALL new components as necessary.
Intermediate (2, 6) clutch friction plates DISASSEMBLE and INSPECT the intermediate (2, 6) clutch friction and steel plates. INSTALL new components as necessary.
Intermediate (2, 6) clutch piston seal leakage INSPECT the intermediate (2, 6) clutch piston and seals. INSTALL new components as necessary.
Intermediate (2, 6) clutch always applied SSC solenoid O-rings cut/damaged INSTALL a new solenoid. REFER to: Solenoid  .
SSC mechanically stuck ON INSTALL a new solenoid. REFER to: Solenoid  .
Intermediate (2, 6) clutch regulator valve stuck ON DISASSEMBLE, CLEAN and INSPECT the intermediate (2, 6) clutch regulator valve and spring. If bore or valve is damaged, INSTALL a new main control valve body. REFER to: Main Control Valve Body .
VBS CB26, CB26 hydraulic circuits leaking DISASSEMBLE and INSPECT the main control valve body and separator plate passages for leakage. INSTALL new components as necessary. REFER to: Main Control Valve Body .
Rear planetary sun gear and shell assembly INSPECT the sun gear and shell for damage that would prevent free rotation. INSTALL new components as necessary.
Intermediate (2, 6) clutch friction plates DISASSEMBLE and INSPECT the intermediate (2, 6) clutch friction and steel plates. INSTALL new components as necessary.
Intermediate (2, 6) clutch piston return spring INSPECT the return spring for proper installation or damage. INSTALL new components as necessary.
Intermediate (2, 6) clutch delayed/soft/slipping apply Incorrect Transmission Strategy programmed into PCM Remove SSC and record solenoid band number. REFER to: Solenoid . Using the scan tool, verify the correct band number is stored in the PCM. If the band numbers do not match, INSTALL a new SSC with correct band number.
SSC solenoid filter partially blocked or restricted CLEAN or INSTALL a new solenoid. REFER to: Solenoid .
SSC mechanically sticking INSTALL a new solenoid. REFER to: Solenoid .
Intermediate (2, 6) clutch regulator valve sticking DISASSEMBLE, CLEAN and INSPECT the intermediate (2, 6) clutch regulator valve. If bore or valve is damaged, INSTALL a new main control valve body. REFER to: Main Control Valve Body  .
VBS CB26, CB26 hydraulic circuits blocked or leaking DISASSEMBLE and INSPECT the main control valve body and separator plate passages for debris/blockage. CLEAN as necessary. REFER to: Main Control Valve Body  .
CB26 supply hydraulic circuit blocked or leaking DISASSEMBLE and INSPECT the transmission case passages for debris/blockage. CLEAN as necessary.
Intermediate (2, 6) clutch friction plates DISASSEMBLE and INSPECT the intermediate (2, 6) clutch friction and steel plates. INSTALL new components as necessary.
Intermediate (2, 6) clutch piston seal leakage INSPECT the intermediate (2, 6) clutch piston and seals. INSTALL new components as necessary.
Intermediate (2, 6) clutch harsh apply Incorrect Transmission Strategy programmed into PCM Remove SSC and record solenoid band number. REFER to: Solenoid  . Using the scan tool, verify the correct band number is stored in the PCM. If the band numbers do not match, INSTALL a new SSC with correct band number.
SSC mechanically sticking INSTALL a new solenoid. REFER to: Solenoid  .
Intermediate (2, 6) clutch regulator valve sticking DISASSEMBLE, CLEAN and INSPECT the intermediate (2, 6) clutch regulator valve and spring. If bore, valve or spring is damaged, INSTALL a new main control valve body. REFER to: Main Control Valve Body .
VBS CB26, CB26 hydraulic circuits blocked or leaking DISASSEMBLE and INSPECT the main control valve body and separator plate passages for debris/blockage/leakage. CLEAN as necessary. REFER to: Main Control Valve Body .
Intermediate (2, 6) clutch friction plates DISASSEMBLE and INSPECT the intermediate (2, 6) clutch friction and steel plates. INSTALL new components as necessary.
Intermediate (2, 6) clutch piston return spring INSPECT the return spring for proper installation and damage. INSTALL new components as necessary.
scientia non olet · About LEMON Manuals