LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2018 >> Taurus Limited, FWD, Gas >> Repair and Diagnosis >> External Pages >> Different car >> Section 35 (Electronic Engine Controls - 1.0L ECOBOOST (92KW/125PS)) >> Diagnosis And Testing >> Electronic Engine Controls >> Pinpoint Tests >> Pinpoint Test C : U0146

Pinpoint Test C : U0146

WARNING: This page is about a different car, the 2018 Ford EcoSport. However, it is still accessible from the selected car via links, so may be relevant.
  1. Normal Operation and Fault Conditions 

    DTC Fault Trigger Conditions 

    DTC Description Fault Trigger Condition
    PCM U0146:00 Lost Communication With Serial Data Gateway "A": No Sub Type Information The PCM sets this DTC if data messages from the GWM over the HS-CAN1 are missing.

    Possible Sources 

    • Communications network concern
    • GWM
    • PCM

  2. C1 VERIFY THE CUSTOMER CONCERN

    • Ignition ON.

    • Verify there is an observable symptom present.

    Is an observable symptom present? 

    Yes  GO to  C2
    No  The system is operating normally at this time. The DTC may have been set due to high network traffic or an intermittent fault condition.

  3. C2 CHECK THE COMMUNICATION NETWORK

    • Using a diagnostic scan tool, perform a network test.

    Did the GWM pass the network test? 

    Yes  GO to  C3
    No 

  4. C3 PERFORM GWM (GATEWAY MODULE A) SELF-TEST

    • Using a diagnostic scan tool, perform a TBM self-test.

    Are any Diagnostic Trouble Codes (DTCs) recorded? 

    Yes 
    No  GO to  C4

  5. C4 CHECK THE BCM (BODY CONTROL MODULE) DIAGNOSTIC TROUBLE CODES (DTCS)

    • Using a diagnostic scan tool, retrieve the BCM Diagnostic Trouble Codes (DTCs).

    Are any Diagnostic Trouble Codes (DTCs) recorded? 

    Yes 
    No  GO to  C5

  6. C5 PERFORM THE PCM (POWERTRAIN CONTROL MODULE) SELF-TEST

    • Using a diagnostic scan tool, perform the PCM self-test.

    Is DTC P0562 or P0563 recorded? 

    Yes  REFER to DTC Chart: Powertrain Control Module (PCM) 
    No  GO to  C6

  7. C6 RECHECK THE PCM (POWERTRAIN CONTROL MODULE) DIAGNOSTIC TROUBLE CODES (DTCS)

    NOTE: If new modules were installed prior to the DTC being set, the module configuration may be incorrectly set during the PMI, or the PMI may not have been carried out.

    • Using a diagnostic scan tool, clear the Diagnostic Trouble Codes (DTCs).

    • Wait 10 seconds.

    • Repeat the PCM self-test.

    Is DTC U0146 still present? 

    Yes  GO to  C7
    No  The system is operating correctly at this time. The DTC may have been set due to high network traffic or an intermittent fault condition.

  8. C7 CHECK FOR DTC (DIAGNOSTIC TROUBLE CODE) U0146 SET IN OTHER MODULES

    • Using a diagnostic scan tool, clear all Diagnostic Trouble Codes (DTCs).

    • Ignition OFF.

    • Ignition ON.

    • Wait 10 seconds.

    • Using a diagnostic scan tool, retrieve all Continuous Memory Diagnostic Trouble Codes (CMDTCs) from all modules.

    Is DTC U0146:87 set in any other module? 

    Yes  GO to  C8
    No  GO to  C9

  9. C8 CHECK FOR CORRECT GWM (GATEWAY MODULE A) OPERATION

    • Ignition OFF.

    • Disconnect and inspect the GWM connector.

    • Repair:

      • corrosion (install new connector or terminals - clean module pins)
      • damaged or bent pins - install new terminals/pins
      • pushed-out pins - install new pins as necessary

    • Reconnect the GWM connector. Make sure it seats and latches correctly.

    • Operate the system and determine if the concern is still present.

    Is the concern still present? 

    Yes  CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no Technical Service Bulletins (TSBs) address this concern, INSTALL a new GWM.
    No  The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.

  10. C9 CHECK FOR CORRECT PCM (POWERTRAIN CONTROL MODULE) OPERATION

    • Ignition OFF.

    • Disconnect and inspect the PCM connectors.

    • Repair:

      • corrosion (install new connector or terminals - clean module pins)
      • damaged or bent pins - install new terminals/pins
      • pushed-out pins - install new pins as necessary

    • Reconnect the PCM connectors. Make sure they seat and latch correctly.

    • Operate the system and determine if the concern is still present.

    Is the concern still present? 

    Yes  CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no Technical Service Bulletins (TSBs) address this concern, Refer to PCM GUIDED ROUTINE TESTING
    No  The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.
scientia non olet · About LEMON Manuals