LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2018 >> Mustang GT, Automatic Trans >> Repair and Diagnosis >> External Pages >> Different car >> Section 86 (Information Center - Instrumentation, Message Center And Warning Chimes (1 Of 2)) >> Description And Operation >> Message Center - System Operation and Component Description >> System Operation >> Warning Messages

Warning Messages

WARNING: This page is about a different car, the 2018 Ford Edge. However, it is still accessible from the selected car via links, so may be relevant.

Adaptive Steering 

The message center provides the adaptive steering messages to supplement and inform the driver of the system states. Depending on the state, the message can be either informational or warning. The IPC receives the adaptive steering message center message request from the GWM over the HS-CAN3. The GWM receives the adaptive steering message center message request from the SASM over the HS-CAN2.

Adaptive Cruise Control 

The message center provides messages explaining the need for driver intervention and system status. The adaptive cruise control messages are supplemental to the cruise control RTT and the adaptive cruise control warning chime. The IPC receives the adaptive cruise control message display from the GWM over the HS-CAN3. The GWM receives the adaptive cruise control message display from the CCM over the HS-CAN2.

AWD 

The IPC provides message center messages to inform the driver of the status of the AWD. The IPC receives the AWD status display message from the GWM over the HS-CAN3. The GWM receives the AWD status display message from the PCM over the HS-CAN1.

Auto Stop-Start 

The message center provides messages explaining the need for driver intervention and system status. The IPC receives the stop/start message request from the GWM over the HS-CAN3. The GWM receives the stop/start message request from the PCM over the HS-CAN1.

Blind Spot Monitoring System (BLIS®)/Cross Traffic Alert (CTA) 

The message center provides messages indicating the reason for the Blind Spot Monitoring System (BLIS®)/Cross Traffic Alert (CTA) fault. The IPC receives the side obstacle sensor status-left and side obstacle sensor status-right messages from the GWM over the HS-CAN3. The GWM receives the side obstacle sensor status-left and side obstacle sensor status-right messages from the SODL and SODR, respectively, over the MS-CAN.

Brake System 

The IPC provides brake system messages for the following concerns and status:

When the parking brake is applied, the BCM sends the parking brake chime request to the GWM over the HS-CAN1. The GWM gateways the message to the IPC over the HS-CAN3 to illuminate the brake warning indicator and turn on the parking brake applied message in the message center.

When a low brake fluid level condition exists, the BCM sends the brake fluid level low message request to the GWM over the HS-CAN1. The GWM gateways the message to the IPC over the HS-CAN3 to illuminate the brake warning indicator and turn on the brake fluid level low message in the message center.

When an ABS or parking brake system concern exists, the ABS module sends the brake (red) warning indicator request message to the GWM over the HS-CAN2. The GWM sends the brake (red) warning indicator request message to the IPC over the HS-CAN3 to illuminate the ABS warning indictor and to turn on the check brake system message center warning display.

Charging System 

The message center provides a warning message indicating the status of the charging system. When a fault is present in the charging system, the BCM sends the battery low state of charge message to the GWM over the HS-CAN1. The IPC receives the battery low state of charge message from the GWM over the HS-CAN3.

Check Fuel Fill Inlet 

The message center provides a check fuel fill inlet message to warn the driver there is a problem with the fuel fill inlet pipe resulting in a significant evaporative emission leak following vehicle refueling. The IPC receives the check fuel fill inlet message request from the GWM over the HS-CAN3. The GWM receives the check fuel fill inlet message request from the PCM over the HS-CAN1.

Door-Liftgate Ajar 

The IPC provides door and liftgate ajar warnings to indicate the status of the doors and the liftgate. The IPC receives the driver door ajar, passenger door ajar, left rear door ajar, the right rear door ajar status and liftgate ajar status messages from the GWM over the HS-CAN3. The GWM receives the driver door ajar, passenger door ajar, left rear door ajar, the right rear door ajar status and liftgate ajar status messages from the BCM over the HS-CAN1. The BCM monitors each of the ajar inputs and sends the specific door ajar status message to the IPC to display the ajar warning indicator and corresponding warning message.

Electronic Park Brake 

The message center provides messages to indicate the status of the electronic parking brake system. The messages displayed are a combination of informational messages, warning and system fault messages. The IPC uses the following messages to display the applicable message center message.

The IPC receives all messages required to display the electronic park brake messages from the GWM over the HS-CAN3.

The GWM receives the parking brake message request and the brake (red) warning indicator request from the ABS module over the HS-CAN2.

The GWM receives the brake fluid level low message request from the BCM module over the HS-CAN1.

EPAS 

The IPC provides a message center message to indicate there is an EPAS system concern. When a fault exists in the EPAS, the PSCM sends a request to the IPC through the GWM.

The IPC receives the EPAS failure message from the GWM over the HS-CAN3.

The GWM receives the EPAS failure message from the PSCM over the HS-CAN2.

Engine On 

The message center provides the engine on warning message to inform the driver they are exiting the vehicle when the engine is running. The IPC uses multiple inputs to determine the vehicle is stopped and the driver is preparing to exit the vehicle. The messages required to control the engine on warning message are as follows:

The IPC receives all required messages from the GWM over the HS-CAN3.

The GWM receives the driver door ajar status from the BCM over the HS-CAN1.

The GWM receives the power pack status, transmission shift mode display and the vehicle speed messages from the PCM over the HS-CAN1.

Engine Over-Temperature 

The message center provides the engine coolant over-temperature warning message to supplement the engine over-temperature RTT and alert the driver the engine is over temperature. The IPC receives the engine overheat indication request and the engine coolant temperature data from the GWM over the HS-CAN3. The GWM receives the engine overheat indication request and the engine over-temperature message from the PCM over the HS-CAN1.

Forward Collision 

The message center provides the forward collision warning messages to inform the driver of the forward collision status. The IPC receives the forward collision warning message request from the GWM over the HS-CAN3. The GWM receives the forward collision warning message request from the CCM over the HS-CAN2.

Hill Start Assist 

The message center provides a message indicating the hill start assist feature is not available due to a fault in the ABS. When a fault is detected and the hill start assist is disabled, the ABS module sends the hill start assist status message to the GWM over the HS-CAN2. The GWM sends the hill start assist status message to the IPC over the HS-CAN3.

Keypad Factory Code 

The message center can display the original keypad factory code when requested. The IPC receives the keypad code message from the GWM over the HS-CAN3. The GWM receives the keypad code message from the BCM over the HS-CAN1. For information on how to retrieve the factory code, Refer to: Handles, Locks, Latches and Entry Systems - System Operation and Component Description .

Lane Keeping System 

The message center provides a warning message for the lane keeping alert and system fault messages for the over all lane keeping system. The IPC receives all required messages from the GWM over the HS-CAN3. The GWM receives the lane keeping system hands off display message, the lane keeping system status display and the camera status message from the IPMA over the HS-CAN2.

Load Shed 

The message center provides load shed messages to inform the driver to use less options to conserve battery voltage. The IPC receives the battery low state of charge message from the GWM over the HS-CAN3. The GWM receives the battery low state of charge message from the BCM over the HS-CAN1.

Memory Seat Status 

The message center provides memory seat status messages to provide the driver confirmation that memory position storing was successful and that recalling a memory position can not be recalled while driving the vehicle. The IPC receives the memory feedback status message from the GWM over the HS-CAN3. The GWM receives the memory feedback status message from the DSM over the MS-CAN.

Oil Life 

The instrument cluster provides messages to inform the driver about the oil life status, oil life reset status and when an oil change is required. The duration of the interval between oil changes is calculated in the PCM and varies due to driving conditions. The PCM assumes a base mileage of 16, 090 km (10, 000 mi) or 1 year for normal driving. However, this number is adjusted down for conditions such as high engine temperature, high engine rpm, use of flex fuel and possibly low oil level. The PCM calculates and provides the engine oil life percent message to the IPC. The oil change minder can be reset at any time by the driver.

The IPC receives the engine oil life message from the GWM over the HS-CAN3. The GWM receives the engine oil life message from the PCM over the HS-CAN1.

The PCM receives the engine oil life data reset message from the GWM over the HS-CAN1. The GWM receives the engine oil life data reset message from the IPC over the HS-CAN3.

Parking Aid System 

The IPC provides messages to indicate the status of the parking aid system. The IPC receives the parking aid rear status message from the GWM over the HS-CAN3. The GWM receives the parking aid rear status message from the PAM over the HS-CAN1.

PATS And Passive Key And Immobilizer System 

The message center provides the starting system fault message to indicate there is a concern with the PATS. The message center provides passive key and immobilizer system messages to indicate the key is in the luggage compartment, the key is left in the vehicle, no key is detected, accessory power is active, to press the brake to start the vehicle or to place the key in the backup slot. The IPC uses the immobilizer message display messaged input from the BCM to display the applicable message center message.

The IPC receives the immobilizer message request from the GWM over the HS-CAN3.

The GWM receives the immobilizer message request from the BCM over the HS-CAN1.

Perimeter Alarm Message Display 

The IPC provides a display to indicate the perimeter alarm has been activated and to start the vehicle to stop the alarm. The IPC receives the perimeter alarm chime request message from the GWM over the HS-CAN3. The GWM receives the perimeter alarm chime request from the BCM over the HS-CAN1.

Power Child Lock-Switch Inhibit And Low Key Fob 

The IPC provides a power child lock warning to inform the driver the child lock feature did not function properly. The power child lock feature is activated through the rear window lockout switch on the driver side master window control switch.

The IPC provides a switch inhibit warning to notify the driver that some switches have been purposely inhibited and are inoperative. For security purposes, interior switches are inhibited by the BCM 20 seconds after the vehicle is electronically locked and prevents someone from using a stick (or other object) through an open window and activating the switch.

The IPC provides a low key fob battery warning to alert the driver the key fob battery needs to be replaced. The low key fob battery warning is not displayed in RUN or START modes if the power child lock warning is active to prevent the BCM from cycling between the two warnings, causing the chime associated with the power child lock warning to repeatedly sound every 4 seconds.

The IPC receives the child lock message request from the GWM over the HS-CAN3. The GWM receives the child lock message request from the BCM over the HS-CAN1.

Powertrain Cooling 

On vehicles equipped with a Gasoline Turbo Direct Injection (GTDI) engine, the IPC provides a message to inform the driver that vehicle performance is reduced to allow the engine to cool. This feature is part of the smart cooling function in the PCM and provides powertrain cooling protection under high ambient temperature conditions.

The IPC receives the powertrain cooling message request from the GWM over the HS-CAN3. The GWM receives the powertrain cooling message request from the PCM over the HS-CAN1.

PRNDL Not In Park (Shift To Park) 

The message center provides a shift to park message to inform the driver the vehicle is not in PARK (P) under 2 sets of conditions. First, the IPC displays the shift to park message if the selector lever is not in PARK (P), the ignition is OFF and the driver door is open or ajar. Second, the message center displays the shift to park message if the selector lever is not in PARK (P), the ignition is ON or in ACC, the driver door is open or ajar and the brake pedal is not applied with vehicle speed less than 5 km/h (3 mph). The IPC uses multiple messages to control the shift to park message.

The IPC receives all required messages from the GWM over the HS-CAN3.

The GWM receives the transmission shift mode display and vehicle speed messages from the PCM over the HS-CAN1.

The GWM receives the driver door ajar status, transport mode and ignition status message from the BCM over the HS-CAN1.

The IPC also uses the park position detect input to determine whether the vehicle is in PARK (P) along with the transmission gear display mode message.

See Park Position Detect Switch component description. Refer to: Instrument Panel Cluster (IPC) - System Operation and Component Description .

Remote Start 

The IPC provides remote start messages to inform the driver the vehicle is in the remote start active state and how to change the state to a drivable state. The remote start message display is active as soon as the vehicle is remote started (that is, the engine is running, but the ignition status is off).

The IPC receives the remote start status message from the GWM over the HS-CAN3. The GWM receives the remote start status message from the BCM over the HS-CAN1.

Stability - Traction Control 

The message center provides stability-traction control system messages to indicate the stability-traction control system status or if the stability-traction control system has a fault and requires service.

When the stability-traction control system has been selected off or on, the ABS module sends the stability-traction control on/off message request to the GWM over the HS-CAN2. The GWM sends the stability-traction control on/off message request to the IPC over the HS-CAN3.

When a fault condition exists in the stability-traction control system, the ABS module sets a DTC and sends the stability-traction control chime request to the GWM over the HS-CAN2. The GWM sends the stability-traction control chime request to the IPC over the HS-CAN3.

Starting System 

The message center provides a starting system message to inform the driver of further actions required to start the engine or to explain the reason for the inability to start the engine. The IPC receives the starting system fault message request and stop/start message request from the GWM over the HS-CAN3. The GWM receives the starting system fault message request and stop/start message request from the PCM over the HS-CAN1.

Spinout Detection System 

The spinout detection feature activates the hazard indicator to alert other vehicles approaching the vehicle following a spinout, potentially reducing the risk of collision, especially in low visibility weather conditions. A spinout is defined as a slip angle greater than 40 degrees followed by 5 seconds of vehicle at rest.

When a spinout is detected, the system activates the hazard indicator and the IPC displays a message to inform the driver that the hazards have been turned on. The IPC receives the vehicle dynamics SOS message from the GWM over the HS-CAN3. The GWM receives the vehicle dynamics SOS message from the ABS module over the HS-CAN2.

Steering Wheel Lock 

The message center provides informational and fault messages to inform the driver of steering wheel lock conditions and to indicate a fault in the system. The IPC receives the steering wheel lock message request from the GWM over the HS-CAN3. The GWM receives the steering wheel lock message request from the BCM over the HS-CAN1.

TPMS 

The IPC provides message center displays to indicate the TPMS sensor training status or a malfunction in the TPMS. The IPC receives the tire pressure system status message from the GWM over the HS-CAN3. The GWM receives the tire pressure system status message from the BCM over the HS-CAN1.

Trailer Sway 

The message center provides a message to inform the driver to slow the vehicle to reduce trailer sway and bring the trailer under control. The IPC receives the trailer sway status message from the GWM over the HS-CAN3. The GWM receives the trailer sway status message from the ABS module over the HS-CAN2.

scientia non olet · About LEMON Manuals