Symptom Chart: Information And Message Center - Warning Messages

Diagnostics in this article assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .

Condition	Possible Sources	Actions
The adaptive cruise control messages are never displayed	Message center concern Cruise control indication concern	OPEN then CLOSE the driver door and VERIFY the driver door ajar message displays correctly with the door open and closed. If the driver door ajar message does not function correctly, GO to Pinpoint Test AO If the driver door ajar message functions correctly, DIAGNOSE the adaptive cruise control RTT. REFER to: Cruise Control or Cruise Control - Vehicles With Adaptive Cruise Control .
A BLIS/ CTA message is always displayed	Message center concern BLIS/ CTA indication concern	OPEN then CLOSE the driver door and VERIFY the driver door ajar message displays correctly with the door open and closed. If the driver door ajar message does not function correctly, GO to Pinpoint Test AO If the driver door ajar message functions correctly, DIAGNOSE the BLIS/ CTA system. REFER to: Blind Spot Information System .
A brake warning (brake fluid level low, parking brake applied or brake system malfunction) message is never or always displayed	Message center concern Brake warning indication concern	NOTE: Disconnecting the GWM creates an unrelated fault to test the overall message center function and display. With the ignition OFF, DISCONNECT GWM C2431. Place the ignition ON and monitor the message center display.If multiple messages and popup displays do not display, GO to Pinpoint Test A If multiple messages and popup displays do display, DIAGNOSE the brake warning indicator.For never on, GO to Pinpoint Test Q For always on, GO to Pinpoint Test R
The ceramic brake wear warning message never or always displayed (GT350 only)	Refer to the Pinpoint Test	GO to Pinpoint Test BC
The charging system warning message is never or always displayed	Message center concern Charging system RTT indication concern	OPEN then CLOSE the driver door and VERIFY the driver door ajar message displays correctly with the door open and closed. If the driver door ajar message does not function correctly, GO to Pinpoint Test AO If the driver door ajar message functions correctly, DIAGNOSE the charging system RTT. GO to Pinpoint Test AM
The check fuel fill inlet message is always displayed	Refer to the Pinpoint Test	GO to Pinpoint Test BD
The convertible top warning message is always displayed	Refer to the Pinpoint Test	GO to Pinpoint Test BE
A door, hood or luggage compartment lid ajar warning message is never or always displayed	Message center concern Door ajar RTT indication concern	NOTE: Disconnecting the GWM creates an unrelated fault to test the overall message center function and display. With the ignition OFF, DISCONNECT GWM C2431. Place the ignition ON and monitor the message center display.If multiple messages and popup displays do not display, GO to Pinpoint Test A If multiple messages and popup displays do display, DIAGNOSE the door ajar RTT. GO to Pinpoint Test AO
The engine on warning message is always displayed (push button start only)	Refer to the Pinpoint Test	GO to Pinpoint Test BF
The engine oil change message is never displayed	Message center concern The PCM has not reached the programmed mileage/time based on the criteria required to display the message.	NOTE: Using the system check in the message center, verify that the oil life is between 1 and 5% for the ENGINE OIL CHANGE SOON message or at 0% for the OIL CHANGE REQUIRED message. OPEN then CLOSE the driver door and VERIFY the DRIVER DOOR AJAR message functions correctly.If the DRIVER DOOR AJAR message does not function correctly, GO to Pinpoint Test AO If the DRIVER DOOR AJAR message functions correctly with the oil life between 0-5%, Refer to IPC Guided Routine Testing .If the DRIVER DOOR AJAR message functions correctly with the oil life not at the specified value, INFORM the customer how the message center functions and how the oil life messages are set.
The engine oil change message is always displayed	The oil life needs reset	RESET the oil life. REFER to the Owner's Literature.
The engine over-temperature warning message is never or always displayed	Message center concern Temperature gauge indication concern.	OPEN then CLOSE the driver door and VERIFY the driver door ajar message displays correctly with the door open and closed. If the driver door ajar message does not function correctly, GO to Pinpoint Test AO If the driver door ajar message functions correctly, DIAGNOSE the temperature gauge. For an inoperative gauge, GO to Pinpoint Test J For an incorrect gauge, GO to Pinpoint Test K
The factory mode message is always on	Vehicle is in factory or transport mode	PLACE the vehicle in normal operation mode. REFER to: Factory Mode Deactivation .
A forward collision warning message is never or always displayed	Message center concern Forward collision system concern.	OPEN then CLOSE the driver door and VERIFY the driver door ajar message displays correctly with the door open and closed. If the driver door ajar message does not function correctly, GO to Pinpoint Test AO If the driver door ajar message functions correctly, DIAGNOSE the forward collision warning system. REFER to: Collision Warning And Collision Avoidance System .
A gas particulate filter warning message is always displayed	Exhaust particulate filter concern Powertrain emissions concern Message center concern	OPEN then CLOSE the driver door and VERIFY the driver door ajar message displays correctly with the door open and closed. If the driver door ajar message does not function correctly, GO to Pinpoint Test AO If the driver door ajar message functions correctly, DIAGNOSE all PCM gas particulate filter Diagnostic Trouble Codes (DTCs). Refer to Engine Controls - Powertrain DTC Charts & Descriptions (Except Diesel & Hybrid) .
The hill start assist warning message is always displayed	Refer to the Pinpoint Test	GO to Pinpoint Test BG
The lane keeping alert system warning message (keep hands on wheel) is never or always displayed	Message center concern Lane keeping alert warning chime concern	OPEN then CLOSE the driver door and VERIFY the driver door ajar message displays correctly with the door open and closed. If the driver door ajar message does not function correctly, GO to Pinpoint Test AO If the driver door ajar message functions correctly, DIAGNOSE the lane keeping alert warning chime. GO to Pinpoint Test BQ
The lane keeping system malfunction or front camera malfunction fault message is always displayed	Message center concern Lane keeping system concern	DIAGNOSE the lane keeping aid system. REFER to: Lane Keeping System .
The launch control message is never displayed	Message center concern Launch control indication concern.	OPEN then CLOSE the driver door and VERIFY the driver door ajar message displays correctly with the door open and closed. If the driver door ajar message does not function correctly, GO to Pinpoint Test AO If the driver door ajar message functions correctly, DIAGNOSE the launch control RTT. GO to Pinpoint Test AS
A load shed message is always displayed	Message center concern Battery charging system concern.	OPEN then CLOSE the driver door and VERIFY the driver door ajar message displays correctly with the door open and closed. If the driver door ajar message does not function correctly, GO to Pinpoint Test AO If the driver door ajar message functions correctly, DIAGNOSE the charging system. REFER to the appropriate Charging System article procedure.
The low oil pressure warning message is never or always displayed	Message center concern Low oil pressure indication concern.	OPEN then CLOSE the driver door and VERIFY the driver door ajar message displays correctly with the door open and closed. If the driver door ajar message does not function correctly, GO to Pinpoint Test AO If the driver door ajar message functions correctly, DIAGNOSE low oil pressure RTT. For 2.3L and 5.0L [non-performance package], GO to Pinpoint Test AU For 2.3L and 5.0L [performance package] and 5.2L, GO to Pinpoint Test AV
A memory seat message is never displayed	Message center concern Memory seat concern.	OPEN then CLOSE the driver door and VERIFY the driver door ajar message displays correctly with the door open and closed. If the driver door ajar message does not function correctly, GO to Pinpoint Test AO If the driver door ajar message functions correctly, DIAGNOSE memory seats. REFER to: Front Seats .
A MyKey® menu is not available or incorrect	MyKey® programmed key in use Number of keys set to unlimited mode Non-Ford approved remote start system installed	NOTE: MyKey® may not be compatible with non-Ford approved remote start systems. REFER to the Owner's Literature.
The parking aid malfunction message is always displayed	Message center concern Parking aid system concern	OPEN then CLOSE the driver door and VERIFY the driver door ajar message displays correctly with the door open and closed. If the driver door ajar message does not function correctly, GO to Pinpoint Test AO If the driver door ajar message functions correctly, DIAGNOSE the parking aid. REFER to: Parking Aid .
A PATS message (no key detected, key inside vehicle, key not inside vehicle or place key in keyholder) is never or always displayed (push button start only)	PATS concern	DIAGNOSE the PATS. REFER to: Passive Anti-Theft System (PATS) .
The perimeter alarm message is always displayed	Message center concern Perimeter alarm concern	NOTE: Disconnecting the GWM creates an unrelated fault to test the overall message center function and display. With the ignition OFF, DISCONNECT GWM C2431. Place the ignition ON and monitor the message center display.If multiple messages and popup displays do not display, GO to Pinpoint Test A If multiple messages and popup displays do display, DIAGNOSE the perimeter alarm. REFER to: Perimeter Anti-Theft Alarm .
The power reduced to lower engine temperature warning message is always displayed	Refer to the Pinpoint Test	DIAGNOSE the engine over-temperature RTT warning indicator. GO to Pinpoint Test AQ
The PRNDL not in park warning message is never or always displayed	Message center concern PRNDL indication concern	OPEN then CLOSE the driver door and VERIFY the driver door ajar message displays correctly with the door open and closed. If the driver door ajar message does not function correctly, GO to Pinpoint Test AO If the driver door ajar message functions correctly, DIAGNOSE the PRNDL. GO to Pinpoint Test X
The shift to park display is never or always on	Refer to the Pinpoint Test	OPEN then CLOSE the driver door and VERIFY the driver door ajar message displays correctly with the door open and closed. If the driver door ajar message does not function correctly, GO to Pinpoint Test AO If the driver door ajar message functions correctly, DIAGNOSE the PRNDL. GO to Pinpoint Test X
The service AdvanceTrac® malfunction warning is never or always displayed	Message center concern Stability-traction control indication concern	OPEN then CLOSE the driver door and VERIFY the driver door ajar message displays correctly with the door open and closed. If the driver door ajar message does not function correctly, GO to Pinpoint Test AO If the driver door ajar message functions correctly, DIAGNOSE the stability-traction control indicator. GO to Pinpoint Test AA
A steering malfunction message is always on	Message center concern EPAS system concern	OPEN then CLOSE the driver door and VERIFY the driver door ajar message displays correctly with the door open and closed. If the driver door ajar message does not function correctly, GO to Pinpoint Test AO If the driver door ajar message functions correctly, DIAGNOSE the EPAS. REFER to: Power Steering .
A TPMS malfunction message is never or always on	Message center concern TPMS warning indication concern	NOTE: Disconnecting the GWM creates an unrelated fault to test the overall message center function and display. With the ignition OFF, DISCONNECT GWM C2431. Place the ignition ON and monitor the message center display.If multiple messages and popup displays do not display, GO to Pinpoint Test A If multiple messages and popup displays do display, DIAGNOSE the TPMS. REFER to: Tire Pressure Monitoring System (TPMS) .
The tire training complete message is never on	TPMS sensor training incomplete	NOTE: This message only appears at the conclusion of the TPMS sensor training procedure. CARRY OUT the TPMS sensor training. REFER to: Tire Pressure Monitoring System (TPMS) Sensor Location Calibration .
A tire training message (train left front, right front, left rear or right rear tire) message is never on	TPMS warning indicator concern TPMS sensor training concern	NOTE: These messages only appear during the TPMS sensor training procedure. VERIFY the TPMS warning indicator functions.If the TPMS warning indicator does not operate, GO to Pinpoint Test AC If the Tire TPMS warning indicator operates, CARRY OUT the TPMS sensor training. REFER to: Tire Pressure Monitoring System (TPMS) Sensor Location Calibration .
The tires not trained message is always on	TPMS sensor training concern	NOTE: This message only appears during the TPMS sensor training procedure. CARRY OUT the TPMS sensor training. REFER to: Tire Pressure Monitoring System (TPMS) Sensor Location Calibration .
The traction control disabled warning is never on	Message center concern Stability-traction control disable indication concern	OPEN then CLOSE the driver door and VERIFY the driver door ajar message displays correctly with the door open and closed. If the driver door ajar message does not function correctly, GO to Pinpoint Test AO If the driver door ajar message functions correctly, DIAGNOSE the traction control disabled indicator (sliding car OFF icon). GO to Pinpoint Test AB
The transport mode message is always on	Vehicle is in transport mode	PLACE the vehicle in normal operation mode. REFER to: Transport Mode Deactivation .
A vehicle starting/ignition status (press brake to start or switch ignition off press power) message is always on	Message center concern Push button start concern	OPEN then CLOSE the driver door and VERIFY the driver door ajar message displays correctly with the door open and closed. If the driver door ajar message does not function correctly, GO to Pinpoint Test AO If the driver door ajar message functions correctly, DIAGNOSE the ignition/starting system concern. REFER to: Steering Wheel And Column Electrical Components .