DTC Chart: Instrument Panel Cluster (IPC)
Diagnostics in this article assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .
| DTC | Description | Action |
|---|---|---|
| P0460:11 | Fuel Level Sensor "A" Circuit: Circuit Short To Ground | GO to Pinpoint Test D |
| P0460:13 | Fuel Level Sensor "A" Circuit: Circuit Open | GO to Pinpoint Test D |
| P1243:06 | Second Fuel Pump Fault or Ground Fault: Algorithm Based Failure | GO to Pinpoint Test D |
| P1346:11 | Fuel Level Sensor "B" Circuit: Circuit Short To Ground | GO to Pinpoint Test D |
| P1346:13 | Fuel Level Sensor "B" Circuit: Circuit Open | GO to Pinpoint Test D |
| P1534:01 | Restraint Deployment Indicator Circuit: General Electrical Failure | Refer to IPC Guided Routine Testing
. Diagnose all RCM Diagnostic Trouble Codes (DTCs). REFER to: Airbag Supplemental Restraint System (SRS) . |
| P1706:00 | High Vehicle Speed Observed in Park: No Sub Type Information | GO to Pinpoint Test X |
| U0100:00 | Lost Communication With ECM/PCM "A": No Sub Type Information | GO to Pinpoint Test BY |
| U0104:00 | Lost Communication With Cruise Control Module: No Sub Type Information | GO to Pinpoint Test CA |
| U0121:00 | Lost Communication With Anti-Lock Brake System (ABS) Control Module: No Sub Type Information | GO to Pinpoint Test CB |
| U0122:00 | Lost Communication With Vehicle Dynamics Control Module: No Sub Type Information | GO to Pinpoint Test CC |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test CD |
| U0146:00 | Lost Communication With Gateway "A": No Sub Type Information | GO to Pinpoint Test CF |
| U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | GO to Pinpoint Test CG |
| U0159:00 | Lost Communication With Parking Assist Control Module "A": No Sub Type Information | GO to Pinpoint Test CI |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to Pinpoint Test CJ |
| U0193:00 | Lost Communication With "Digital Audio Control Module A": No Sub Type Information | GO to Pinpoint Test CK |
| U0212:00 | Lost Communication With Steering Column Control Module: No Sub Type Information | GO to Pinpoint Test CL |
| U0212:82 | Lost Communication With Steering Column Control Module: Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test CL |
| U0232:00 | Lost Communication With Side Obstacle Detection Control Module - Left: No Sub Type Information | GO to Pinpoint Test CM |
| U0233:00 | Lost Communication With Side Obstacle Detection Control Module - Right: No Sub Type Information | GO to Pinpoint Test CM |
| U023A:00 | Lost Communication With Image Processing Module A: No Sub Type Information | GO to Pinpoint Test CN |
| U0253:00 | Lost Communication With Accessory Protocol Interface Module: No Sub Type Information | GO to Pinpoint Test CO |
| U0256:00 | Lost Communication With Front Controls Interface Module "A": No Sub Type Information | GO to Pinpoint Test CP |
| U0260:00 | Lost Communication With Seat Control Switch Module "A": No Sub Type Information | GO to Pinpoint Test CQ |
| U0401:00 | Invalid Data Received from ECM/PCM A: No Sub Type Information | This DTC sets when the IPC receives invalid network data for the speedometer, engine temperature, or transmission fluid temperature data from the PCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the PCM and other modules on the network. REFER to the appropriate Electronic Engine Controls article. If no Diagnostic Trouble Codes (DTCs) are present in the PCM, DIAGNOSE the observable symptom. |
| U0401:81 | Invalid Data Received from ECM/PCM A: Invalid Serial Data Received | This DTC sets when the IPC receives invalid network data for the speedometer, engine temperature, or transmission fluid temperature data from the PCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the PCM and other modules on the network. REFER to the appropriate Electronic Engine Controls article. If no Diagnostic Trouble Codes (DTCs) are present in the PCM, DIAGNOSE the observable symptom. |
| U0401:82 | Invalid Data Received from ECM/PCM A: Alive/Sequence Counter Incorrect/Not Updated | This DTC sets when the IPC receives invalid network data for the forward collision, adaptive cruise control or rear axle fluid temperature (digital IPC) data from the PCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the PCM and other modules on the network. REFER to the appropriate Electronic Engine Controls article. If no Diagnostic Trouble Codes (DTCs) are present in the PCM, DIAGNOSE the observable symptom. |
| U0401:86 | Invalid Data Received from ECM/PCM A: Signal Invalid | This DTC sets when the IPC receives invalid network data for the odometer from the PCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the PCM and other modules on the network. REFER to the appropriate Electronic Engine Controls article. If no Diagnostic Trouble Codes (DTCs) are present in the PCM, DIAGNOSE the observable symptom. |
| U0405:56 | Invalid Data Received From Cruise Control Module: Invalid/Incompatible Configuration | This DTC sets when the IPC receives invalid network data for adaptive cruise control from the CCM. CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the diagnostic scan tool. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| U0415:00 | Invalid Data Received From Anti-Lock Brake System (ABS) Control Module: No Sub Type Information | This DTC sets when the IPC receives invalid accelerometer network data from the ABS module. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the ABS module and other modules on the network. REFER to: Anti-Lock Brake System (ABS) And Stability Control . If no Diagnostic Trouble Codes (DTCs) are present in the ABS module, DIAGNOSE the observable symptom. |
| U0415:81 | Invalid Data Received From Anti-Lock Brake System (ABS) Control Module: Invalid Serial Data Received | This DTC sets when the IPC receives invalid accelerometer network data from the ABS module. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the ABS module and other modules on the network. REFER to: Anti-Lock Brake System (ABS) And Stability Control . If no Diagnostic Trouble Codes (DTCs) are present in the ABS module, DIAGNOSE the observable symptom. |
| U0415:82 | Invalid Data Received From Anti-Lock Brake System (ABS) Control Module: Alive/Sequence Counter Incorrect/Not Updated | This DTC sets when the IPC receives invalid or missing updated network data from the ABS module. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the ABS module and other modules on the network. REFER to: Anti-Lock Brake System (ABS) And Stability Control . If no Diagnostic Trouble Codes (DTCs) are present in the ABS module, DIAGNOSE the observable symptom. |
| U0420:00 | Invalid Data Received From Power Steering Control Module: No Sub Type Information | GO to Pinpoint Test CR |
| U0420:82 | Invalid Data Received From Power Steering Control Module: Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test CR |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | This DTC sets when the IPC receives invalid TPMS network data from the BCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the BCM and other modules on the network. REFER to: Body Control Module (BCM) . If no Diagnostic Trouble Codes (DTCs) are present in the BCM, DIAGNOSE the observable symptom. |
| U0424:80 | Invalid Data Received From HVAC Control Module: ISO/SAE Reserved | This DTC sets when the IPC receives invalid outside air temperature network data from the PCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the PCM and other modules on the network. REFER to the appropriate Electronic Engine Controls article. If no Diagnostic Trouble Codes (DTCs) are present in the PCM, DIAGNOSE the observable symptom. |
| U0424:81 | Invalid Data Received From HVAC Control Module: Invalid Serial Data Received | This DTC sets when the IPC receives unknown outside air temperature network data from the PCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the PCM and other modules on the network. REFER to the appropriate Electronic Engine Controls article. If no Diagnostic Trouble Codes (DTCs) are present in the PCM, DIAGNOSE the observable symptom. |
| U0424:82 | Invalid Data Received From HVAC Control Module: Alive/Sequence Counter Incorrect/Not Updated | This DTC sets in the IPC when the outside air temperature network data is missing from the PCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the PCM and other modules on the network. REFER to the appropriate Electronic Engine Controls article. If no Diagnostic Trouble Codes (DTCs) are present in the PCM, DIAGNOSE the observable symptom. |
| U0431:82 | Invalid Data Received From Body Control Module "A": Alive/Sequence Counter Incorrect/Not Updated | This DTC sets in the IPC when load shed network messages are missing from the BCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the BCM and other modules on the network. REFER to: Body Control Module (BCM) . If no Diagnostic Trouble Codes (DTCs) are present in the BCM, DIAGNOSE the observable symptom. |
| U0452:81 | Invalid Data Received From Restraints Control Module: Invalid Serial Data Received | This DTC sets when the IPC receives invalid network data from the RCM due to incorrect Belt-Minder® configuration in the IPC. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the RCM and other modules on the network. REFER to: Airbag Supplemental Restraint System (SRS) . If no Diagnostic Trouble Codes (DTCs) are present in the RCM, DIAGNOSE the observable symptom. |
| U0533:00 | Invalid Data Received From Side Obstacle Detection Control Module-Left: No Sub Type Information | This DTC sets when the IPC receives invalid network data from the SODL. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the SODL and other modules on the network. REFER to: Blind Spot Information System . If no Diagnostic Trouble Codes (DTCs) are present in the RCM, DIAGNOSE the observable symptom. |
| U0533:56 | Invalid Data Received From Side Obstacle Detection Control Module-Left: Invalid/Incompatible Configuration | CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the diagnostic scan tool. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| U0533:82 | Invalid Data Received From Side Obstacle Detection Control Module-Left: Alive/Sequence Counter Incorrect/Not Updated | This DTC sets when the IPC receives invalid network data from the SODL. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the SODL and other modules on the network. REFER to: Blind Spot Information System . If no Diagnostic Trouble Codes (DTCs) are present in the RCM, DIAGNOSE the observable symptom. |
| U0534:00 | Invalid Data Received From Side Obstacle Detection Control Module-Right: Invalid/Incompatible Configuration | This DTC sets when the IPC receives invalid network data from the SODR. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the SODR and other modules on the network. REFER to: Blind Spot Information System . If no Diagnostic Trouble Codes (DTCs) are present in the RCM, DIAGNOSE the observable symptom. |
| U0534:56 | Invalid Data Received From Side Obstacle Detection Control Module-Right: Invalid/Incompatible Configuration | CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the diagnostic scan tool. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| U0534:82 | Invalid Data Received From Side Obstacle Detection Control Module-Right: Alive/Sequence Counter Incorrect/Not Updated | This DTC sets when the IPC receives invalid network data from the SODR. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the SODR and other modules on the network. REFER to: Blind Spot Information System . If no Diagnostic Trouble Codes (DTCs) are present in the RCM, DIAGNOSE the observable symptom. |
| U0542:82 | Invalid Data Received From Headlamp Control Module "A": Alive/Sequence Counter Incorrect/Not Updated | This DTC sets when the IPC receives invalid network data from the HCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the HCM and other modules on the network. REFER to: Headlamps or Headlamps - Vehicles With: SVT Performance Package . If no Diagnostic Trouble Codes (DTCs) are present in the RCM, DIAGNOSE the observable symptom. |
| U0557:80 | Invalid Data Received From Front Controls Interface Module "A": ISO/SAE Reserved | This DTC sets when the IPC receives invalid outside air temperature network data from the FCIM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the FCIM and other modules on the network. REFER to: Information and Entertainment System . (without touchscreen audio) or REFER to: Information And Entertainment System (with touchscreen audio). If no Diagnostic Trouble Codes (DTCs) are present in the FCIM, DIAGNOSE the observable symptom. |
| U0557:81 | Invalid Data Received From Front Controls Interface Module "A": Invalid Serial Data Received | This DTC sets when the IPC receives invalid outside air temperature network data from the FCIM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the FCIM and other modules on the network. REFER to: Information and Entertainment System . (without touchscreen audio) or REFER to: Information And Entertainment System (with touchscreen audio). If no Diagnostic Trouble Codes (DTCs) are present in the FCIM, DIAGNOSE the observable symptom. |
| U0557:82 | Invalid Data Received From Front Controls Interface Module "A": Alive/Sequence Counter Incorrect/Not Updated | This DTC sets when the IPC receives invalid outside air temperature network data from the FCIM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the FCIM and other modules on the network. REFER to: Information and Entertainment System . (without touchscreen audio) or REFER to: Information And Entertainment System (with touchscreen audio). If no Diagnostic Trouble Codes (DTCs) are present in the FCIM, DIAGNOSE the observable symptom. |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the diagnostic scan tool. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| U3000:04 | Control Module: System Internal Failure | CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U3000:04 is retrieved again, Refer to IPC Guided Routine Testing . |
| U3000:41 | Control Module: General Checksum Failure | CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U3000:41 is retrieved again, Refer to IPC Guided Routine Testing . |
| U3000:42 | Control Module: General Memory Failure | CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U3000:42 is retrieved again, Refer to IPC Guided Routine Testing . |
| U3000:44 | Control Module: Data Memory Failure | CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U3000:44 is retrieved again, Refer to IPC Guided Routine Testing . |
| U3000:46 | Control Module: Calibration/Parameter Memory Failure | CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U3000:46 is retrieved again, Refer to IPC Guided Routine Testing . |
| U3000:54 | Control Module: Missing Calibration | CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect calibration files. If there have been recent service actions with this module, REFLASH the IPC. If there have been no recent service actions, Refer to IPC Guided Routine Testing . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test CS |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test CU |
| U300A:64 | Ignition Switch: Signal Plausibility Failure | DTC U300A:64 sets in continuous memory when the IPC detects a messaged START input for 15 seconds or longer. Once the fault condition is detected, the IPC operates with limited functionality for 15 seconds then returns to full functionality. DIAGNOSE any ignition or starting system concerns. REFER to: Steering Wheel And Column Electrical Components . |