LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2018 >> Fusion Platinum, FWD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 34 (Automatic Transmission - 6F50/6F55 - Fusion (Except Hybrid)) >> Diagnosis And Testing >> Automatic Transmission >> Pinpoint Tests >> Pinpoint Test D : Shift Solenoid D (SSD) >> Pinpoint Test D : Shift Solenoid D (SSD)

Pinpoint Test D : Shift Solenoid D (SSD)

WARNING: This page is about a different variant/trim than selected.

  1. D1 RETRIEVE AND RECORD ALL DTCS

    • Using the diagnostic scan tool, retrieve all DTCs.

    Are DTCs P0765, P0768, P0769, P0982 and/or P0983 present? 

    Yes  For DTCs P0765, P0768 and/or P0769, GO to  D2For DTC P0982 and/or P0769, GO to  D4For DTCs P0983 and/or P0769, GO to  D6
    No  REFER to: Diagnosis By Symptom .

  2. D2 CHECK THE SHIFT SOLENOID D CONTROL CIRCUIT FOR AN OPEN

    • Ignition OFF.

    • Disconnect Transmission Vehicle Harness C168 .

    • Inspect the connectors for damaged or pushed-out terminals, corrosion, loose wires and missing or damaged seals.

    • Measure:
      Positive Lead Measurement / Action Negative Lead
      C168-12
      GFD194722Courtesy of FORD MOTOR COMPANY
      		 C1231E-30

    Is the resistance less than 3 ohms? 

    Yes  GO to  D3
    No  REPAIR the circuit.

  3. D3 CHECK SHIFT SOLENOID D (SSD) FOR AN OPEN

    • Measure:
      Positive Lead Measurement / Action Negative Lead
      Component side resistance pin 12.
      GFD194722Courtesy of FORD MOTOR COMPANY
      		 Component side resistance pin 15.

    Is the resistance between 4 and 7.2 ohms? 

    Yes 
    No  REMOVE the main control cover. Refer to: Main Control Cover . INSPECT the solenoid body for metal shavings on the exposed metal contacts or other components. CLEAN the solenoid body and RECHECK the resistance value. If the resistance value is out of specification and an open circuit is not found, INSTALL a new solenoid body. REFER to: Solenoid Body . PERFORM the Transmission Strategy Download procedure. REFER to: Transmission Strategy Download .

  4. D4 CHECK THE SHIFT SOLENOID D (SSD) CONTROL CIRCUIT FOR A SHORT TO GROUND

    • Ignition OFF.

    • Disconnect Transmission Vehicle Harness C168 .

    • Inspect the connectors for damaged or pushed-out terminals, corrosion, loose wires and missing or damaged seals.

    • Measure:
      Positive Lead Measurement / Action Negative Lead
      C168-12
      GFD194722Courtesy of FORD MOTOR COMPANY
      		 Ground

    Is the resistance greater than 10, 000 ohms? 

    Yes  GO to  D5
    No  REPAIR the circuit.

  5. D5 CHECK SHIFT SOLENOID D (SSD) FOR A SHORT TO GROUND

    • Measure:
      Positive Lead Measurement / Action Negative Lead
      Component side resistance pin 12.
      GFD194722Courtesy of FORD MOTOR COMPANY
      		 Ground

    Is the resistance less than 3 ohms? 

    Yes  REMOVE the main control cover. Refer to: Main Control Cover . INSPECT the solenoid body for metal shavings on the exposed metal contacts or other components. CLEAN the solenoid body and RECHECK the resistance value. If the resistance value is out of specification and a short to ground is not found, INSTALL a new solenoid body. REFER to: Solenoid Body . PERFORM the Transmission Strategy Download procedure. REFER to: Transmission Strategy Download .
    No 

  6. D6 CHECK THE SHIFT SOLENOID D (SSD) CONTROL CIRCUIT FOR A SHORT TO POWER

    • Ignition OFF.

    • Disconnect Transmission Vehicle Harness C168 .

    • Inspect the connectors for damaged or pushed-out terminals, corrosion, loose wires and missing or damaged seals.

    • Ignition ON.

    • Measure:
      Positive Lead Measurement / Action Negative Lead
      C168-12
      GFD194723Courtesy of FORD MOTOR COMPANY
      		 Ground

    Is any voltage present? 

    Yes  REPAIR the circuit.
    No 
scientia non olet · About LEMON Manuals