LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2018 >> Fusion Platinum, FWD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 136 (Starting System - 2.5L DURATEC (125KW/170PS)) >> Diagnosis And Testing >> Starting System >> Pinpoint Test(s) >> Pinpoint Test C : C113A:11 Or C113A:15 >> Pinpoint Test C : C113A:11 Or C113A:15

Pinpoint Test C : C113A:11 Or C113A:15

WARNING: This page is about a different variant/trim than selected.

  1. C1 CHECK FOR BCM (BODY CONTROL MODULE) DIAGNOSTIC TROUBLE CODES (DTCS)

    • Ignition ON.
    • Using a diagnostic scan tool, perform the BCM self-test.

    Is DTC C113A:11 present? 

    Yes  GO to  C2
    No  If DTC C113A:15 is present, GO to  C4
    For all other BCM Diagnostic Trouble Codes (DTCs), REFER to: Body Control Module (BCM) .

  2. C2 CHECK THE PCM (POWERTRAIN CONTROL MODULE) FOR A SHORT TO GROUND

    • Ignition OFF.
    • Disconnect PCM C1551B .
    • Ignition ON.
    • Using a diagnostic scan tool, clear the BCM Diagnostic Trouble Codes (DTCs).
    • Using a diagnostic scan tool, perform the BCM self-test.

    Is BCM DTC C113A:11 present? 

    Yes  GO to  C3
    No  GO to  C7

  3. C3 CHECK THE PCM (POWERTRAIN CONTROL MODULE) WAKE-UP SIGNAL CIRCUIT FOR A SHORT TO GROUND

    • Ignition OFF.
    • Measure:
      Positive Lead Measurement / Action Negative Lead
      C1551B-21
      GFD190359Courtesy of FORD MOTOR COMPANY
      		 Ground

    Is the resistance greater than 10, 000 ohms? 

    Yes  GO to  C7
    No  REPAIR the circuit.

  4. C4 CHECK THE PCM (POWERTRAIN CONTROL MODULE) WAKE-UP SIGNAL CIRCUIT FOR A SHORT TO VOLTAGE

    • Ignition OFF.
    • Disconnect PCM C1551B if necessary.
    • Disconnect BCM C2280C .
    • Ignition ON.
    • Measure:
      Positive Lead Measurement / Action Negative Lead
      C1551B-21
      GFD190360Courtesy of FORD MOTOR COMPANY
      		 Ground

    Is any voltage present? 

    Yes  REPAIR the circuit.
    No  GO to  C5

  5. C5 CHECK THE PCM (POWERTRAIN CONTROL MODULE) WAKE-UP SIGNAL CIRCUIT FOR AN OPEN

    • Ignition OFF.
    • Measure:
      Positive Lead Measurement / Action Negative Lead
      C1551B-21
      GFD190359Courtesy of FORD MOTOR COMPANY
      		 C2280C-18

    Is the resistance less than 3 ohms? 

    Yes  GO to  C6
    No  REPAIR the circuit.

  6. C6 CHECK FOR CORRECT BCM (BODY CONTROL MODULE) OPERATION

    • Ignition OFF.
    • Disconnect and inspect all BCM connectors.
    • Repair:

      • corrosion (install new connectors or terminals - clean module pins)
      • damaged or bent pins - install new terminals/pins
      • pushed-out pins - install new pins as necessary

    • Reconnect the BCM connectors. Make sure they seat and latch correctly.
    • Operate the system and determine if the concern is still present.

    Is the concern still present? 

    Yes  CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW the TSB instructions. If no Technical Service Bulletins (TSBs) address this concern, BCM Hardware Testing -- Fusion (Except Hybrid)
    No  The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.

  7. C7 CHECK FOR CORRECT PCM (POWERTRAIN CONTROL MODULE) OPERATION

    • Ignition OFF.
    • Disconnect and inspect all PCM connectors.
    • Repair:

      • corrosion (install new connectors or terminals - clean module pins)
      • damaged or bent pins - install new terminals/pins
      • pushed-out pins - install new pins as necessary

    • Reconnect the PCM connectors. Make sure they seat and latch correctly.
    • Operate the system and determine if the concern is still present.

    Is the concern still present? 

    Yes  CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW the TSB instructions. If no Technical Service Bulletins (TSBs) address this concern,
    No  The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.
scientia non olet · About LEMON Manuals