DTC Chart: HCM
Diagnostics in this article assume a certain skill level and knowledge of Ford-specific diagnostic practices. Refer to: Diagnostic Methods .
| DTC | Description | Action |
|---|---|---|
| C1A03:29 | Left Front Height Sensor: Signal Invalid | GO to Pinpoint Test W |
| C1A05:29 | Left Rear Height Sensor: Signal Invalid | GO to Pinpoint Test W |
| B103C:01 | Left Headlamp Control: General Electrical Failure | If a low beam headlamp is inoperative, Go to PINPOINT TEST B If a low beam headlamp is always on, Go to PINPOINT TEST F If a high beam headlamp is inoperative, Go to PINPOINT TEST D If a high beam headlamp is always on, Go to PINPOINT TEST H Except North America, if the automatic headlamp leveling is inoperative/does not operate correctly, Go to PINPOINT TEST R |
| B103D:01 | Right Headlamp Control: General Electrical Failure | If a low beam headlamp is inoperative, Go to PINPOINT TEST B If a low beam headlamp is always on, Go to PINPOINT TEST F If a high beam headlamp is inoperative, Go to PINPOINT TEST D If a high beam headlamp is always on, Go to PINPOINT TEST H Except North America, if the automatic headlamp leveling is inoperative/does not operate correctly, Go to PINPOINT TEST R If a front turn lamp is inoperative or always on, Refer to: Turn Signal and Hazard Lamps . If a parking lamp is inoperative or always on, Refer to: Parking, Rear and License Plate Lamps . |
| B1087:00 | LIN Bus "A": No Sub Type Information | For halogen headlamps, Go to PINPOINT TEST Q For LED headlamps, Go to PINPOINT TEST F |
| B1088:00 | LIN Bus "B": No Sub Type Information | For halogen headlamps, Go to PINPOINT TEST Q For LED headlamps, Go to PINPOINT TEST F |
| B1D64:01 | Left Headlamp Swiveling Motor: General Electrical Failure | Go to PINPOINT TEST R |
| B1D65:01 | Right Headlamp Swiveling Motor: General Electrical Failure | Go to PINPOINT TEST R |
| U0100:00 | Lost Communication With ECM/PCM "A": No Sub Type Information | Go to PINPOINT TEST K |
| U0121:00 | Lost Communication With Anti-Lock Brake System (ABS) Control Module: No Sub Type Information | Go to PINPOINT TEST L |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | Go to PINPOINT TEST M |
| U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | Go to PINPOINT TEST N |
| U0212:00 | Lost Communication With Steering Column Control Module: No Sub Type Information | Go to PINPOINT TEST O |
| U0253:00 | Lost Communication With Accessory Protocol Interface Module: No Sub Type Information | Go to PINPOINT TEST P |
| U0401:00 | Invalid Data Received from ECM/PCM A: No Sub Type Information | This DTC sets when the HCM receives invalid network data from the PCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the PCM and other modules on the network. Refer to ENGINE CONTROLS - INTRODUCTION (EXCEPT DIESEL & HYBRID) . |
| U0415:00 | Invalid Data Received From Anti-Lock Brake System (ABS) Control Module: No Sub Type Information | This DTC sets when the HCM receives invalid network data from the ABS module. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the ABS module and other modules on the network. Refer to: Anti-Lock Brake System Component Testing . |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | This DTC sets when the HCM receives invalid network data from the BCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the BCM and other modules on the network. Refer to: Body Control Module (BCM) . |
| U0452:00 | Invalid Data Received From Restraints Control Module: No Sub Type Information | This DTC sets when the HCM receives invalid network data from the RCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the RCM and other modules on the network. Refer to: Supplemental Restraint System . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the scan tool. Refer to: Module Programming . If there have been no recent service actions, INSTALL a new HCM to correct the failure to retain configuration data. |
| U3000:49 | Control Module: Internal Electronic Failure | CLEAR the DTC. REPEAT the self-test. If the DTC returns, INSTALL a new HCM. |