Network Message Chart
Module Network Input Messages - IPC
| Broadcast Message | Originating Module | Message Purpose |
|---|---|---|
| Adaptive cruise control warning request | CCM | Input used to control the adaptive cruise control warning and fault messages. |
| Air ambient temperature filtered actual | PCM | Input used to provide the outside air temperature display. |
| AWD service required | PCM | Input used for the AWD gauge display. |
| AWD status | PCM | Input used for the AWD gauge display. |
| Blind Spot Information System (BLIS®) status - left | SODL | Input used to control the Blind Spot Information System (BLIS®) message displays. |
| Blind Spot Information System (BLIS®) status - right | SODR | Input used to control the Blind Spot Information System (BLIS®) message displays. |
| Brake fluid level low | BCM | Input used to display the low brake fluid level warning message. |
| Brake (red) warning indicator request | ABS module | ABS input used to display the brake system malfunction warning messages. |
| Bulb failure indication | BCM | Input used to display a bulb failure messages. |
| Compass direction (touchscreen audio) | APIM | Input used to provide the compass display. |
| Cruise control status | PCM | Input used to control the cruise control RTT indicator. |
| Door status | BCM | Input used to display the individual door ajar warning messages. |
| Econometer data | PCM | Input used for the calculation of the instantaneous fuel economy and the Average Fuel Economy (AFE) displays. |
| EPAS display | PSCM | Input used to display the service power steering message. |
| Engine coolant temperature | PCM | Input used to display the engine over-temperature message. |
| Engine MIL request | PCM | Input used to display the engine malfunction message. |
| Engine service indication | PCM | Input used to provide the change oil service message display. |
| Forward collision warning request | CCM | Input used to control the forward collision warning and fault messages. |
| GPS data (except touchscreen audio) | GPSM | Input used to provide the compass display. |
| Hill start assist status | ABS module | Input used to provide the hill start assist message display. |
| Key warning indication | BCM | Used to display the key not inside vehicle message (push button start only). |
| Lane keeping system hands off display | IPMA | Input used to display the hands off steering wheel warning message. |
| Parking aid active | PAM | Input used to display the parking aid malfunction and service required messages. |
| Parking aid disable status | PAM | Input used to display the parking aid cannot be disabled message for MyKey®. |
| Parking brake status | ABS module | Input used to display the parking brake applied message. |
| PATS indication | BCM | Input used to display the immobilizer active message for the PATS. |
| Passive key status | RFA module | Used to display the passive key left inside vehicle message and the key not in vehicle message (passive entry only). |
| Power system status | BCM | Input used to display the charging system warning messages. |
| Push button start indication | BCM | Input used to display the press brake to start message (push button start only). |
| Safety belt status | RCM | Input used to control the buckle up safety belt warning for MyKey®. |
| Selected display language | APIM | Input used to display the selected language. |
| Stop-start message request (1.5L or 2.0L only) | PCM | Input used to display the auto stop-start messages. |
| Temperature display units | APIM | Input used to set the temperature display units to Fahrenheit or Celsius. |
| Tire pressure indication | BCM | Input used to display the TPMS malfunction warning messages and the TPMS tire sensor training messages. |
| Trailer lamp connection status | TRM | Input used to disable Blind Spot Information System (BLIS®) and display the Blind Spot Information System (BLIS®) trailer connected message. |
| Transport mode | BCM | Input used to provide the vehicle in transport mode display. |
| Transmission gear display | TCM | Input used to display the turn ignition off message (push button start only). |
| Transmission message request | RFA | Input used to display transmission related messages and the transmission not in park message (push button start only). |
| Transmission service required | TCM | Input used to display the transmission malfunction messages. |
| Vehicle trip display units | APIM | Input used to set the trip display units to kilometers or miles. |
| Washer fluid level low | BCM | Input used for the low washer fluid level message display. |
| Wheel rotation count | ABS module | Input used for the calculation of the instantaneous fuel economy and the Average Fuel Economy (AFE) displays. |