LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2017 >> Transit Connect XL, Van Cargo >> Repair and Diagnosis >> Engine Performance >> Testing & Diagnosis >> Engine Controls - Pinpoint Test JF: Integrated Ignition Coil On Plug Coils A-J Failure Through Pinpoint Test Z: Intermittent - (Except Diesel & Hybrid) >> Pinpoint Test KD: Electric Exhaust Gas RECIRCULATION (EEGR) System >> Test Procedure

Test Procedure

  1. KD1 CHECK FOR DTCS 

    Are DTCs P0400, P0403, or P1408 present? 

    Yes No
    For DTC P1408, GO to  KD9.
    For all others, GO to  KD2.    		 For symptoms without DTCs, GO to  KD2.
    For all others, RETURN to SYMPTOM CHARTS for further direction.
  2. KD2 CHECK THE EEGR CONNECTOR 
    NOTE: If the DTC is intermittent, wiggle the harness and connectors when taking measurements.
    • Check the connection of the EEGR connector.

    Are the connector contacts clean and correctly seated? 

    Yes No
    GO to  KD3. REPAIR as necessary.
    Clear the PCM DTCs. REPEAT the self-test.
  3. KD3 CHECK THE VPWR CIRCUITS FOR AN OPEN 
    • Ignition ON, engine OFF.
    • EEGR Assembly connector disconnected.
    • Measure the voltage between:
    (+) EEGR Assembly Connector, Harness Side (-) Vehicle Battery
    VPWR - Pin 2 Negative terminal
    VPWR - Pin 5 Negative terminal

    Are the voltages greater than 10.5 V? 

    Yes No
    GO to  KD4. REPAIR the open circuit. Clear the PCM DTCs.
    REPEAT the self-test.
  4. KD4 CHECK THE EEGR CIRCUITS FOR AN OPEN 
    • Ignition OFF.
    • PCM connector disconnected.
    • Measure the resistance between:
    (+) EEGR Assembly Connector, Harness Side (-) PCM Connector, Harness Side
    EGRMC1 - Pin 1 EGRMC1 - Pin E48
    EGRMC2 - Pin 3 EGRMC2 - Pin E47
    EGRMC3 - Pin 4 EGRMC3 - Pin E46
    EGRMC4 - Pin 6 EGRMC4 - Pin E31

    Are the resistances less than 5 ohms? 

    Yes No
    GO to  KD5. REPAIR the open circuit. Clear the PCM DTCs.
    REPEAT the self-test.
  5. KD5 CHECK THE EEGR CIRCUITS FOR A SHORT TO GROUND 
    • Measure the resistance between:
    (+) EEGR Assembly Connector, Harness Side (-) Vehicle Battery
    EGRMC1 - Pin 1 Negative terminal
    EGRMC2 - Pin 3 Negative terminal
    EGRMC3 - Pin 4 Negative terminal
    EGRMC4 - Pin 6 Negative terminal

    Are the resistances greater than 10K ohms? 

    Yes No
    GO to  KD6. REPAIR the short circuit. Clear the PCM DTCs.
    REPEAT the self-test.
  6. KD6 CHECK FOR A SHORT BETWEEN EEGR CIRCUITS 
    NOTE: Refer to the PCM connector pin numbers in the beginning of this pinpoint test.
    • Measure the resistance between:
    (+) EEGR Assembly Connector, Harness Side (-) EEGR Assembly Connector, Harness Side
    EGRMC3 - Pin 4 EGRMC1 - Pin 1
    EGRMC3 - Pin 4 EGRMC2 - Pin 3
    EGRMC3 - Pin 4 EGRMC4 - Pin 6
    EGRMC1 - Pin 1 EGRMC2 - Pin 3
    EGRMC1 - Pin 1 EGRMC4 - Pin 6
    EGRMC2 - Pin 3 EGRMC4 - Pin 6

    Are the resistances greater than 10K ohms? 

    Yes No
    GO to  KD7. REPAIR the short circuit. Clear the PCM DTCs.
    REPEAT the self-test.
  7. KD7 CHECK THE EEGR CIRCUITS FOR A SHORT TO VOLTAGE 
    • Ignition ON, engine OFF.
    • Measure the voltage between:
    (+) EEGR Assembly Connector, Harness Side (-) Vehicle Battery
    EGRMC1 - Pin 1 Negative terminal
    EGRMC2 - Pin 3 Negative terminal
    EGRMC3 - Pin 4 Negative terminal
    EGRMC4 - Pin 6 Negative terminal

    Is any voltage present? 

    Yes No
    REPAIR the short circuit. Clear the PCM DTCs.
    REPEAT the self-test.    		 GO to  KD8.
  8. KD8 CHECK THE EEGR COILS FOR AN OPEN 
    • Ignition OFF.
    • Measure the resistance between:
    (+) EEGR Assembly Connector, Component Side (-) EEGR Assembly Connector, Component Side
    EGRMC1 - Pin 1 VPWR - Pin 2
    EGRMC2 - Pin 3 VPWR - Pin 2
    EGRMC3 - Pin 4 VPWR - Pin 5
    EGRMC4 - Pin 6 VPWR - Pin 5

    Are the resistances between 12 - 24 ohms? 

    Yes No
    GO to  KD11. INSTALL a new EEGR assembly.
    REFER to the Service Information, Engine Emission Control.
    Clear the PCM DTCs. REPEAT the self-test.
  9. KD9 COMPARE THE ACTUAL MAP VOLTAGE TO THE MAP PID VOLTAGE 
    • Ignition OFF.
    • PCM connector connected.
    • Ignition ON, engine OFF.
    • Access the PCM and monitor the MAP (VOLT) PID.
    • Record the MAP PID voltage.
    • Ignition ON, engine running.
    • Record the MAP PID voltage.
    • Increase engine speed to 1, 000 RPM.
    • Record the MAP PID voltage.
    • Increase engine speed to 2, 000 RPM.
    • Record the MAP PID voltage.

    Does the MAP PID voltage stay within 0.5 V of the actual MAP voltage? 

    Yes No
    The concern is not present at this time.
    Make sure the MAP sensor is correctly seated and the vacuum source is not blocked.
    Clear the PCM DTCs. REPEAT the self-test.    		 GO to  KD10.
  10. KD10 CARRY OUT THE KOER SELF-TEST 
    • Carry out the PCM KOER self-test.

    Is DTC P1408 retrieved again? 

    Yes No
    GO to PINPOINT TESTS Z . REFER to Symptom Charts, NO DIAGNOSTIC TROUBLE CODES (DTCS) PRESENT SYMPTOM CHART INDEX , to continue diagnosis.
  11. KD11 CHECK FOR CORRECT OPERATION 
    • Disconnect all the PCM connectors.
    • EEGR Assembly connector disconnected.
    • Visually inspect for:
      • pushed out pins
      • corrosion
    • Connect all the PCM connectors, and the EEGR valve connector, and make sure they seat correctly.
    • Carry out the PCM self-test.
    • Verify the concern is still present.

    Is the concern still present? 

    Yes No
    INSTALL a new EEGR assembly.
    REFER to the Service Information, Engine Emission Control.
    Clear the PCM DTCs. REPEAT the self-test.    		 The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector.
scientia non olet · About LEMON Manuals