LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2017 >> Mustang EcoBoost, Automatic Trans >> Repair and Diagnosis >> Accessories & Equipment >> Gauges & Instrument Panels >> Information Center - Instrumentation, Message Center And Warning Chimes >> Description And Operation >> Message Center - System Operation and Component Description >> System Operation >> Reconfigurable Telltales (RTT's)

Reconfigurable Telltales (RTT's)

Blind Spot Monitoring System (BLIS) Off 

The IPC provides a RTT to inform the driver that the Blind Spot Monitoring System (BLIS) is turned off. The IPC receives the side obstacle detect status-left and side obstacle detect status-right messages from the GWM over the HS-CAN3. The GWM receives the side obstacle detect status-left and side obstacle detect status-right messages from the SODL and SODR over the MS-CAN.

Charging System 

The IPC provides a charging system message center indicator along with message displays indicating the status of the charging system. When a charging system fault is present, the BCM sends the battery low state of charge message to the GWM over the HS-CAN1. The GWM sends the battery low state of charge message to the IPC to turn on the charging system RTT and to display the message center warning messages.

Cruise Control 

The IPC uses the following messaged inputs to control the cruise control RTT:

The IPC receives the cruise control messages from the GWM over the HS-CAN3. The GWM receives the cruise control messages from the PCM over the HS-CAN1.

Door Ajar 

The IPC provides a door ajar RTT along with message displays to indicate the status of the doors or luggage compartment lid. The BCM monitors each of the ajar inputs and sends the corresponding ajar message (driver door ajar status, passenger door ajar status or luggage compartment lid ajar) to the GWM over the HS-CAN1 when a door or the luggage compartment lid is ajar. The IPC receives the door ajar status message from the GWM over the HS-CAN3.

Drive Mode 

The IPC provides multiple RTT indicators to inform the driver of the selected drive mode (sport, sport plus, rain/snow, track mode and drag strip mode). The IPC receives the powertrain drive mode message from the GWM over the HS-CAN3. The GWM receives the powertrain drive mode message from the PCM over the HS-CAN1.

Engine Over-Temperature 

The IPC provides a RTT to alert the driver the engine is over temperature. The IPC receives the engine overheat indication request and the engine coolant temperature data messages from the GWM over the HS-CAN3. The GWM receives the engine overheat indication request and the engine coolant temperature data messages from the PCM over the HS-CAN1.

Launch Control 

The IPC provides the launch control RTT indicator to inform the driver of the launch control system status. The IPC receives the launch control mode message from the GWM over the HS-CAN3. The GWM receives the launch control mode message from the PCM over the HS-CAN1.

Low Fuel 

The IPC provides the low fuel RTT indicator in 2 colors, amber and red. The IPC uses the calculated DTE to control the low fuel RTT. The low fuel RTT illuminates whenever the DTE reads 80 km (50 miles) with an administrator key or 120 km (75 miles) with a MyKey ® key.

Low Oil Pressure 

The engine oil pressure switch is hardwired to the PCM. The IPC requires 2 messaged inputs to control the low oil pressure RTT. The first is the oil pressure warning indicator request message and the second is the engine rpm data message above 400 rpm. Both the oil pressure warning indicator request and engine RPM data messages are sent from the PCM to the GWM over the HS-CAN1. The IPC receives the oil pressure warning indicator request and engine rpm data messages from the GWM over the HS-CAN3.

Overspeed Warning (Gulf Cooperative Countries [GCC]) 

The IPC provides an overspeed warning RTT to inform the driver that the vehicle speed has reached or exceeded the 120 km/h (75 mph) threshold. The IPC receives the vehicle speed signal from the GWM over the HS-CAN3. The GWM receives the vehicle speed signal from the PCM over the HS-CAN1.

Powertrain Malfunction (Wrench) 

The IPC provides a powertrain malfunction (wrench) RTT to indicate transmission, Electronic Throttle Control (ETC) and BCM concerns.

The IPC receives all the required messages from the GWM over the HS-CAN3.

The GWM receives the body service required message from the BCM over the HS-CAN1.

The GWM receives the transmission service required, engine service required and AWD service required messages from the PCM over the HS-CAN1.

Steering Mode 

The IPC provides the steering mode RTT to indicate the driver steering mode selected (sport, comfort or normal). The IPC receives the steering effort status message from the GWM over the HS-CAN3. The GWM receives the steering effort status message from the PSCM over the HS-CAN2.

Vehicle Dynamics (Damper Control) (SVT Only) 

The IPC provides 4 RTT indicators to inform the driver of the selected suspension mode. The IPC receives the suspension driver mode status message from the GWM over the HS-CAN3. The GWM receives the suspension driver mode status message from the VDM over the HS-CAN2.

scientia non olet · About LEMON Manuals