LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2017 >> Fusion S >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 101 (Parking Brake System - Parking Brake And Actuation (Hybrid/ENERGI)) >> Diagnosis And Testing >> Parking Brake >> Pinpoint Tests >> Pinpoint Test E : The Parking Brake Does Not Hold The Vehicle, Does Not Apply, Does Not Release Using The Parking Brake Switch >> Pinpoint Test E : The Parking Brake Does Not Hold The Vehicle, Does Not Apply, Does Not Release Using The Parking Brake Switch

Pinpoint Test E : The Parking Brake Does Not Hold The Vehicle, Does Not Apply, Does Not Release Using The Parking Brake Switch

WARNING: This page is about a different variant/trim than selected.

  1. E1 CHECK FOR ABS (ANTI-LOCK BRAKE SYSTEM) MODULE DIAGNOSTIC TROUBLE CODES (DTCS)

    NOTE: A HS-CAN issue or concern results in a failure to release the parking brake.

    • Ignition ON.

    • Using a diagnostic scan tool, carry out the ABS module self-test.

    Are any "lost communication" or "invalid data" Diagnostic Trouble Codes (DTCs) present in the ABS module? 

    Yes  DIAGNOSE the communication concern. REFER to: Module Communications Network (Hybrid/Energi) .
    No  If any of the Diagnostic Trouble Codes (DTCs) from the DTC Fault Trigger Conditions table are present, GO to  E2
    For all other Diagnostic Trouble Codes (DTCs), GO to the DTC Chart: Anti-Lock Brake System (ABS) Module. Refer to: DTC Chart: Anti-Lock Brake System (ABS) Module

  2. E2 CHECK THE ACTUATOR MOTOR CIRCUITS FOR AN OPEN

    • Ignition OFF.

    • Disconnect ABS module C135 .

    • Disconnect the suspect parking brake actuator motor electrical connector.

    • For the LH actuator motor, measure:
      Positive Lead Measurement / Action Negative Lead
      C3529-1
      GFD197351Courtesy of FORD MOTOR COMPANY
      		 C135-12
      C3529-2
      GFD197351Courtesy of FORD MOTOR COMPANY
      		 C135-13

    • For the RH actuator motor, measure:
      Positive Lead Measurement / Action Negative Lead
      C3551-1
      GFD197351Courtesy of FORD MOTOR COMPANY
      		 C135-3
      C3551-2
      GFD197351Courtesy of FORD MOTOR COMPANY
      		 C135-2

    Are the resistances less than 3 ohms? 

    Yes  If DTC C2007:13 or C2008:13 are the only Diagnostic Trouble Codes (DTCs) are present, GO to  E6If other Diagnostic Trouble Codes (DTCs) are present, GO to  E3
    No  INSPECT the actuator motor jumper harness and connectors for correct routing, damaged connectors, spread terminals, bent or pushed-out pins or any signs of corrosion. INSTALL a new jumper harness as necessary.If the jumper harness is OK, REPAIR the circuit.

  3. E3 CHECK THE ACTUATOR MOTOR CIRCUITS FOR A SHORT TO GROUND

    • For the LH actuator motor, measure:
      Positive Lead Measurement / Action Negative Lead
      C3529-1
      GFD197351Courtesy of FORD MOTOR COMPANY
      		 Ground
      C3529-2
      GFD197351Courtesy of FORD MOTOR COMPANY
      		 Ground

    • For the RH actuator motor, measure:
      Positive Lead Measurement / Action Negative Lead
      C3551-1
      GFD197351Courtesy of FORD MOTOR COMPANY
      		 Ground
      C3551-2
      GFD197351Courtesy of FORD MOTOR COMPANY
      		 Ground

    Are the resistances greater than 10, 000 ohms? 

    Yes  GO to  E4
    No  INSPECT the actuator motor jumper harness and connectors for correct routing, damaged connectors, spread terminals, bent or pushed-out pins or any signs of corrosion. INSTALL a new jumper harness as necessary.If the jumper harness is OK, REPAIR the circuit.

  4. E4 CHECK THE ACTUATOR MOTOR CIRCUITS FOR A SHORT TOGETHER

    • For the LH actuator motor, measure:
      Positive Lead Measurement / Action Negative Lead
      C3529-1
      GFD197351Courtesy of FORD MOTOR COMPANY
      		 C3529-2

    • For the RH actuator motor, measure:
      Positive Lead Measurement / Action Negative Lead
      C3551-1
      GFD197351Courtesy of FORD MOTOR COMPANY
      		 C3551-2

    Is the resistance greater than 10, 000 ohms? 

    Yes  GO to  E5
    No  INSPECT the actuator motor jumper harness and connectors for correct routing, damaged connectors, spread terminals, bent or pushed-out pins or any signs of corrosion. INSTALL a new jumper harness as necessary.If the jumper harness is OK, REPAIR the circuit.

  5. E5 CHECK THE ACTUATOR MOTOR CIRCUITS FOR A SHORT TO VOLTAGE

    NOTE: Performing this step sets Diagnostic Trouble Codes (DTCs) in the ABS module.

    • Ignition ON.

    • For the LH actuator motor, measure:
      Positive Lead Measurement / Action Negative Lead
      C3529-1
      GFD197352Courtesy of FORD MOTOR COMPANY
      		 Ground
      C3529-2
      GFD197352Courtesy of FORD MOTOR COMPANY
      		 Ground

    • For the RH actuator motor, measure:
      Positive Lead Measurement / Action Negative Lead
      C3551-1
      GFD197352Courtesy of FORD MOTOR COMPANY
      		 Ground
      C3551-2
      GFD197352Courtesy of FORD MOTOR COMPANY
      		 Ground

    Is any voltage present? 

    Yes  INSPECT the actuator motor jumper harness and connectors for correct routing, damaged connectors, spread terminals, bent or pushed-out pins or any signs of corrosion. INSTALL a new jumper harness as necessary.If the jumper harness is OK, REPAIR the circuit.
    No  GO to  E6

  6. E6 CHECK THE BRAKE CALIPER BALL SCREW DRIVE

    • Ignition OFF.

    • Using a torque wrench, turn the ball screw drive on the brake caliper counterclockwise. It should not take more than 5 Nm (44 lb-in) to turn the ball screw drive.

    Does the ball screw drive turn with less than 5 Nm (44 lb-in) or turning force? 

    Yes  GO to  E7
    No  INSTALL a new brake caliper. REFER to: Rear Disc Brake System (Hybrid/Energi) .

  7. E7 CHECK THE ACTUATOR MOTOR RESISTANCE

    • Ignition OFF.

    • Measure:
      Positive Lead Measurement / Action Negative Lead
      Suspect Actuator Motor Electrical Connector Pin-1, Component Side
      GFD197351Courtesy of FORD MOTOR COMPANY
      		 Suspect Actuator Motor Electrical Connector Pin-2, Component Side

    Is the resistance less than 500 ohms? 

    Yes  GO to  E8
    No  INSTALL a new parking brake actuator motor. REFER to: Parking Brake Actuator Motor .

  8. E8 CHECK FOR CORRECT ABS (ANTI-LOCK BRAKE SYSTEM) MODULE OPERATION

    • Inspect ABS module C135 .

    • Repair:

      • corrosion (install new connector or terminal - clean module pins)
      • damaged or bent pins - install new terminals or pins
      • pushed-out pins - install new pins as necessary

    • Connect ABS module C135 . Make sure it seats and latches correctly.

    • Connect the suspect parking brake actuator motor electrical connector. Make sure it seats and latches correctly.

    • Operate the system and determine if the concern is still present.

    Is the concern still present? 

    Yes  CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW the TSB instructions. For hybrid vehicles, if no Technical Service Bulletins (TSBs) exist for this concern, INSTALL a new ABS module. REFER to: Anti-Lock Brake System (ABS) And Stability Control (Hybrid/Energi) . For all other vehicles, if no Technical Service Bulletins (TSBs) exist for this concern, Refer to: Anti-Lock Brake System Component Testing (Hybrid/Energi) .
    No  The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector. ADDRESS the root cause of any connector or pin issues.
scientia non olet · About LEMON Manuals