Pinpoint Test H : B135C:11, B135C:15

H1 CHECK FOR HSWM (HEATED STEERING WHEEL MODULE) DTC (DIAGNOSTIC TROUBLE CODE) B135C:11
- Review the retrieved Diagnostic Trouble Codes (DTCs).
Is DTC B135C:11 present?

Yes GO to H2

No GO to H5

H2 CHECK THE HEATER ELEMENT VOLTAGE CIRCUIT FOR A SHORT TO GROUND

Ignition OFF.

Disconnect HSWM C2406 .

Measure:

Positive Lead	Measurement / Action	Negative Lead
C2406-8	Courtesy of FORD MOTOR COMPANY	Ground

Is the resistance greater than 10, 000 ohms?

Yes

GO to H6

GO to H3

H3 CHECK THE HEATER ELEMENT VOLTAGE CIRCUIT FOR A SHORT TO GROUND

Remove the steering column shrouds to access the clockspring connectors. REFER to: Steering Column Shrouds .

Disconnect SCCM .

Measure:

Positive Lead	Measurement / Action	Negative Lead
C2406-8	Courtesy of FORD MOTOR COMPANY	Ground

Is the resistance greater than 10, 000 ohms?

Yes

GO to H4

No	REPAIR the circuit.

H4 CHECK THE HEATER ELEMENT FOR A SHORT TO GROUND

Remove the driver airbag. REFER to: Driver Airbag .

Disconnect Clockspring C218E .

On the steering wheel side, measure:

Positive Lead	Measurement / Action	Negative Lead
C218E-1	Courtesy of FORD MOTOR COMPANY	Ground

Is the resistance greater than 10, 000 ohms?

Yes	INSTALL a new clockspring. REFER to: Clockspring . Using a diagnostic scan tool, CLEAR the HSWM Diagnostic Trouble Codes (DTCs) and CARRY OUT the HSWM self-test. If DTC B135C:11 returns, INSTALL a new SCCM. REFER to: Steering Column Control Module (SCCM) .

No	INSTALL a new steering wheel. REFER to: Steering Wheel .

H5 CHECK THE HEATER ELEMENT VOLTAGE AND GROUND CIRCUIT FOR A SHORT TO VOLTAGE

Ignition OFF.

Remove the steering column shrouds to access the clockspring connectors. REFER to: Steering Column Shrouds .

Disconnect SCCM .

Disconnect HSWM C2406 .

Ignition ON.

Measure:

Positive Lead	Measurement / Action	Negative Lead
C2406-8	Courtesy of FORD MOTOR COMPANY	Ground
C2406-7	Courtesy of FORD MOTOR COMPANY	Ground

Is any voltage present?

Yes	REPAIR the circuit in question.

GO to H6

H6 CHECK THE HEATER ELEMENT AND CIRCUIT RESISTANCE

Ignition OFF.

Disconnect SCCM (if not previously disconnected).

Measure:

Positive Lead	Measurement / Action	Negative Lead
C2406-7	Courtesy of FORD MOTOR COMPANY	C2406-8

Is the resistance between 1.6 and 3.1 ohms?

Yes

GO to H10

No	If the resistance is less than 1.6 ohms, GO to H7If the resistance is greater than 3.1 ohms, GO to H8

H7 CHECK THE HEATER ELEMENT CIRCUITS FOR A SHORT

Measure:

Positive Lead	Measurement / Action	Negative Lead
C2406-7	Courtesy of FORD MOTOR COMPANY	C2406-8

Is the resistance greater than 10, 000 ohms?

Yes

GO to H9

No	REPAIR the circuits.

H8 CHECK THE HEATER ELEMENT CIRCUITS FOR AN OPEN

Measure:

Positive Lead	Measurement / Action	Negative Lead
C2406-7	Courtesy of FORD MOTOR COMPANY	C2414C
C2406-8	Courtesy of FORD MOTOR COMPANY	C2414C

Are the resistances less than 3 ohms?

Yes

GO to H9

No	REPAIR the circuit in question.

H9 CHECK THE HEATER ELEMENT RESISTANCE

Remove the driver airbag. REFER to: Driver Airbag .

Disconnect Clockspring C218E .

On the steering wheel side, measure:

Positive Lead	Measurement / Action	Negative Lead
C218E-1	Courtesy of FORD MOTOR COMPANY	C218E-2

Is the resistance between 1.6 and 3.1 ohms?

Yes	INSTALL a new clockspring. REFER to: Clockspring . Using a diagnostic scan tool, CLEAR the HSWM Diagnostic Trouble Codes (DTCs) and CARRY OUT the HSWM self-test. If DTC B135C:11 returns, INSTALL a new SCCM. REFER to: Steering Column Control Module (SCCM) .

No	INSTALL a new steering wheel. REFER to: Steering Wheel .

H10 CHECK FOR CORRECT HSWM (HEATED STEERING WHEEL MODULE) OPERATION

Disconnect HSWM C2406 .

Inspect for the following and repair as necessary:
- corrosion (install new connector or terminals - clean module pins)
- damaged or bent pins - install new terminals/pins
- pushed-out pins - install new pins as necessary

Connect HSWM C2406 .

Reconnect all other previously disconnected connectors. Make sure all connectors are seated and latched correctly.

Ignition ON.

Using a diagnostic scan tool, clear all HSWM Diagnostic Trouble Codes (DTCs).

Using a diagnostic scan tool, carry out the HSWM self-test.

Operate the system and determine if the concern is still present.

Is the concern still present?

Yes	CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no Technical Service Bulletins (TSBs) address this concern, INSTALL a new HSWM. REFER to: Heated Steering Wheel Module (HSWM) .

No	The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.