Symptom Chart(s)
Diagnostics in this information assume a certain skill level and knowledge of Ford-specific diagnostic practices. Refer to: Diagnostic Methods .
Symptom Chart: Parking Aid - Audible
| Condition | Possible Sources | Action |
|---|---|---|
| A module does not communicate with the scan tool | Fuse Wiring, terminals or connectors Parking Aid Module (PAM) |
REFER to: Communications Network . |
| The audible parking aid is inoperative | Refer to the Pinpoint Test | GO to Pinpoint Test A |
| Continuous or intermittent tone when no obstacles or fault codes are present | Dirty or iced over parking aid sensor(s) | CLEAN the rear bumper and sensors with high-pressure water. |
| Ice between parking aid sensor(s) and bezel(s) | ALLOW time for the ice between the parking aid sensor(s) and bezel(s) to melt. | |
| Parking aid sensor(s) locked into the rear bumper incorrectly | INSTALL the parking aid sensor(s) into the parking aid sensor bezel(s) correctly. | |
| Parking aid sensors are not aligned correctly | CARRY OUT the azimuth and elevation system checks.REFER to: Azimuth System Check .REFER to: Elevation System Check . | |
| The parking aid speaker is inoperative | Wiring, Terminals or connectors ACM Audio DSP |
For vehicles equipped with a 4.2-inch (107-mm) display, REFER to: Information and Entertainment System
. For vehicles equipped with a 8-inch (203-mm) display, REFER to: Information and Entertainment System . |
| The parking aid disable switch does not operate correctly | Refer to the Pinpoint Test | GO to Pinpoint Test K |
| The parking aid disable switch status LED is inoperative or always on. | Refer to the Pinpoint Test | GO to Pinpoint Test J |
| The parking aid menu is not available in the message center and cannot be deactivated | A MyKey ® restricted key is in use | The parking aid disable feature is not available when a MyKey ® restricted key is in use. This is normal operation. |
Diagnostics in this information assume a certain skill level and knowledge of Ford-specific diagnostic practices. Refer to: Diagnostic Methods .
Symptom Chart: Parking Aid - Visual
| Condition | Possible Sources | Action |
|---|---|---|
| The rear video is inoperative | Refer to the Pinpoint Test | GO to Pinpoint Test S |
| The video camera display is showing "Rear Video Camera is Unavailable Please Contact Your Dealership" and a black screen/no image | Refer to the Pinpoint Test | GO to Pinpoint Test S |
| Static/flashing/blinking/flickering/scrolling or rolling image/screen/scrolling horizontal lines | Refer to the Pinpoint Test | GO to Pinpoint Test T |
| Poor image quality (foggy/cloudy/fuzzy/blurry/hazy image or moisture/water in lens or black spots) | Refer to the Pinpoint Test | GO to Pinpoint Test T |
| Manual zoom function is inoperative | Refer to the Pinpoint Test | GO to Pinpoint Test AA |
| Visual park aid alert is inoperative | Refer to the Pinpoint Test | GO to Pinpoint Test U |
| Fixed guidelines are not displayed on the video image | Refer to the Pinpoint Test | GO to Pinpoint Test V |
| Active guidelines are not displayed on the video image | Steering wheel is in straight-ahead position | Normal condition. Active guidelines are not shown unless steering wheel is rotated. |
| Refer to the Pinpoint Test | GO to Pinpoint Test V | |
| Video camera delay feature is inoperative | Video camera delay feature is disabled | ENABLE the video camera delay feature within rear camera settings. |
| Refer to the Pinpoint Test | GO to Pinpoint Test V | |
| Video image is upside down | Video camera is not configured | If the vehicle was built on or after November 04, 2013, CONFIGURE the camera using a diagnostic scan tool under Electrical>Service Functions>LIN New Module Initialization If the vehicle was built on or before November 17, 2013, turn the ignition ON and leave on for 5 minutes to allow the Image Processing Module - B (IPM-B)/camera flash operation to complete. |
| All other image concerns | Refer to the Pinpoint Test | GO to Pinpoint Test S |