DTC Chart: Instrument Panel Cluster (IPC)
Diagnostics in this service information assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .
DTC Chart - IPC
| DTC | Description | Action |
|---|---|---|
| P0460:11 | Fuel Level Sensor "A" Circuit: Circuit Short To Ground | For single sender L-shaped fuel tank, GO to Pinpoint Test C . For dual sender saddle-type fuel tank, GO to Pinpoint Test D . |
| P0460:13 | Fuel Level Sensor "A" Circuit: Circuit Open | For single sender L-shaped fuel tank, GO to Pinpoint Test C . For dual sender saddle-type fuel tank, GO to Pinpoint Test D . |
| P1243:06 | Second Fuel Pump Fault or Ground Fault: Algorithm Based Failure | GO to Pinpoint Test D |
| P1346:11 | Fuel Level Sensor "B" Circuit: Circuit Short To Ground | GO to Pinpoint Test D |
| P1346:13 | Fuel Level Sensor "B" Circuit: Circuit Open | GO to Pinpoint Test D |
| P1534:01 | Restraint Deployment Indicator Circuit: General Electrical Failure | Refer to IPC Hardware Testing . Diagnose all RCM Diagnostic Trouble Codes (DTCs). REFER to: AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) . |
| P1706:00 | High Vehicle Speed Observed in Park: No Sub Type Information | GO to Pinpoint Test Z |
| U0100:00 | Lost Communication With ECM/PCM "A": No Sub Type Information | GO to Pinpoint Test BI |
| U0101:00 | Lost Communication with TCM: No Sub Type Information | GO to Pinpoint Test BJ |
| U0104:00 | Lost Communication With Cruise Control Module: No Sub Type Information | GO to Pinpoint Test BK |
| U0121:00 | Lost Communication With Anti-Lock Brake System (ABS) Control Module: No Sub Type Information | GO to Pinpoint Test BL |
| U0121:87 | Lost Communication With Anti-Lock Brake System (ABS) Control Module: Missing Message | GO to Pinpoint Test BL |
| U0131:00 | Lost Communication With Power Steering Control Module: No Sub Type Information | GO to Pinpoint Test BM |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test BN |
| U0140:87 | Lost Communication With Body Control Module: Missing Message | GO to Pinpoint Test BN |
| U0146:00 | Lost Communication With Gateway "A": No Sub Type Information | GO to Pinpoint Test BO |
| U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | GO to Pinpoint Test BP |
| U0151:87 | Lost Communication With Restraints Control Module: Missing Message | GO to Pinpoint Test BP |
| U0154:87 | Lost Communication With Restraints Occupant Classification System Module: Missing Message | GO to Pinpoint Test BQ |
| U0159:00 | Lost Communication With Parking Assist Control Module "A": No Sub Type Information | GO to Pinpoint Test BR |
| U016A:00 | Lost Communication With Global Positioning System Module: No Sub Type Information | GO to Pinpoint Test BS |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to Pinpoint Test BT |
| U0199:00 | Lost Communication With "Door Control Module A": No Sub Type Information | GO to Pinpoint Test BU |
| U0212:00 | Lost Communication With Steering Column Control Module: No Sub Type Information | GO to Pinpoint Test BV |
| U0232:00 | Lost Communication With Side Obstacle Detection Control Module - Left: No Sub Type Information | GO to Pinpoint Test BW |
| U0233:00 | Lost Communication With Side Obstacle Detection Control Module - Right: No Sub Type Information | GO to Pinpoint Test BW |
| U023A:00 | Lost Communication With Image Processing Module A: No Sub Type Information | GO to Pinpoint Test BX |
| U0241:00 | Lost Communication With Headlamp Control Module "A": No Sub Type Information | GO to Pinpoint Test BX |
| U0401:00 | Invalid Data Received from ECM/PCM A: No Sub Type Information | This DTC sets when the IPC receives invalid network data for the speedometer, temperature or odometer data from the PCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the PCM and other modules on the network. Refer to ENGINE CONTROLS - INTRODUCTION (EXCEPT DIESEL & HYBRID) . Refer to the appropriate Engine article for the procedure. If no Diagnostic Trouble Codes (DTCs) are present in the PCM, DIAGNOSE the observable symptom. |
| U0401:81 | Invalid Data Received from ECM/PCM A: Invalid Serial Data Received | This DTC sets when the IPC receives invalid network data for the speedometer, temperature or odometer data from the PCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the PCM and other modules on the network. Refer to ENGINE CONTROLS - INTRODUCTION (EXCEPT DIESEL & HYBRID) . Refer to the appropriate Engine article for the procedure. If no Diagnostic Trouble Codes (DTCs) are present in the PCM, DIAGNOSE the observable symptom. |
| U0401:82 | Invalid Data Received from ECM/PCM A: Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test BI |
| U0405:56 | Invalid Data Received From Cruise Control Module: Invalid/Incompatible Configuration | This DTC sets when the IPC receives invalid network data for adaptive cruise control from the Cruise Control Module (C-CM). CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the scan tool. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| U0415:56 | Invalid Data Received From Anti-Lock Brake System (ABS) Control Module: Invalid/Incompatible Configuration | This DTC sets when the IPC receives invalid network data for adaptive cruise control from the Cruise Control Module (C-CM). CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the scan tool. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| U0420:82 | Invalid Data Received From Power Steering Control Module: Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test BM |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | This DTC sets when the IPC receives invalid network TPMS data from the BCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the BCM and other modules on the network. REFER to: Body Control Module (BCM) . If no Diagnostic Trouble Codes (DTCs) are present in the BCM, DIAGNOSE the observable symptom. |
| U0424:00 | Invalid Data Received From HVAC Control Module: No Sub Type Information | This DTC sets when the IPC receives invalid network data for the outside air temperature display from the HVAC module. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the HVAC, PCM and other modules on the network. REFER to: Climate Control System - Vehicles With: Dual Automatic Temperature Control (DATC) . REFER to: Climate Control System - Vehicles With: Electronic Manual Temperature Control (EMTC) . Refer to the appropriate Engine article for the procedure. If no Diagnostic Trouble Codes (DTCs) are present in the HVAC or PCM, DIAGNOSE the observable symptom. |
| U0424:81 | Invalid Data Received From HVAC Control Module: Invalid Serial Data Received | This DTC sets when the IPC receives invalid network data for the outside air temperature display from the HVAC module. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the HVAC, PCM and other modules on the network. REFER to: Climate Control System - Vehicles With: Dual Automatic Temperature Control (DATC) . REFER to: Climate Control System - Vehicles With: Electronic Manual Temperature Control (EMTC) . Refer to the appropriate Engine article for the procedure. If no Diagnostic Trouble Codes (DTCs) are present in the HVAC or PCM, DIAGNOSE the observable symptom. |
| U0424:82 | Invalid Data Received From HVAC Control Module: Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test BY |
| U0452:81 | Invalid Data Received From Restraints Control Module: Invalid Serial Data Received | This DTC sets when the IPC receives invalid network data from the RCM due to incorrect Belt-Minder® configuration in the IPC. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the RCM and other modules on the network. REFER to: AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) . If no Diagnostic Trouble Codes (DTCs) are present in the RCM, DIAGNOSE the observable symptom. |
| U046B:86 | Invalid Data Received From Global Positioning System Module: Signal Invalid | This DTC sets when the IPC receives invalid network data from the GPSM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the GPSM and other modules on the network. Refer to the appropriate Information and Entertainment System article for the procedure. If no Diagnostic Trouble Codes (DTCs) are present in the GPSM, DIAGNOSE the observable symptom. |
| U0533:56 | Invalid Data Received From Side Obstacle Detection Control Module-Left: Invalid/Incompatible Configuration | This DTC sets when the IPC receives invalid network data from the SODL. CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the scan tool. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| U0533:82 | Invalid Data Received From Side Obstacle Detection Control Module-Left: Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test BW |
| U0534:56 | Invalid Data Received From Side Obstacle Detection Control Module-Right: Invalid/Incompatible Configuration | This DTC sets when the IPC receives invalid network data from the SODR. CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the scan tool. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| U0534:82 | Invalid Data Received From Side Obstacle Detection Control Module-Right: Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test BW |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the scan tool. REFER to: Module Configuration - System Operation and Component Description . If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| U3000:04 | Control Module: System Internal Failure | CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U3000:04 is retrieved again, Refer to IPC Hardware Testing . |
| U3000:41 | Control Module: General Checksum Failure | CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U3000:41 is retrieved again, Refer to IPC Hardware Testing . |
| U3000:42 | Control Module: General Memory Failure | CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U3000:42 is retrieved again, Refer to IPC Hardware Testing . |
| U3000:43 | Control Module: Special Memory Failure | CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U3000:43 is retrieved again, Refer to IPC Hardware Testing . |
| U3000:44 | Control Module: Data Memory Failure | CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U3000:44 is retrieved again, Refer to IPC Hardware Testing . |
| U3000:46 | Control Module: Calibration/Parameter Memory Failure | CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U3000:46 is retrieved again, Refer to IPC Hardware Testing . |
| U3000:54 | Control Module: Missing Calibration | CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect calibration files. If there have been recent service actions with this module, REFLASH the IPC. If there have been no recent service actions, Refer to IPC Hardware Testing . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test BZ |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test CA |
| U300A:64 | Ignition Switch: Signal Plausibility Failure | DTC U300A:64 sets in continuous memory when the IPC detects a messaged START input for 15 seconds or longer. Once the fault condition is detected, the IPC operates with limited functionality for 15 seconds then returns to full functionality. DTC U300A:64 sets in continuous memory when the IPC detects a messaged START input for 15 seconds or longer. Once the fault condition is detected, the IPC operates with limited functionality for 15 seconds then returns to full functionality. DIAGNOSE any ignition or starting system concerns. REFER to: Steering Wheel and Column Electrical Components . |